Bennett Marine AutoTrimPro Operation manual

Installation & User's Guide For Hydraulic Trim Tab Systems
All-in-one trim tab control system
IMPORTANT SAFETY INSTRUCTIONS: Read and follow all instructions. Keep this manual on your boat.

Congrats!
Behind You For The Distance
Bennett’s legendary customer service and support is a priceless perk to your
new purchase! Our expert staff with over 50 years of trim tab experience is
ready to assist with your installation, help with troubleshooting, or answer any
of your questions along the way.
How to Contact Us
Call us at 1-954-427-1400, email [e-mail], or go to
BennettTrimTabs.com/Contact and ll out the online form. Please allow 24
hours for online requests. Our ofce hours are Monday through Friday from
8:00 a.m. to 5:00 p.m. (Eastern Standard Time).
The Benefits of Trim Tabs
Increase Visibility For A Safer Ride: Keeping your bow down at reduced
speeds is important, especially in congested waters or foul weather. Bennett trim
tabs enable you to plane at a much lower speed, operating your boat
more safely.
Run More Efciently: Getting up on plane quicker means your boat spends
less time running inefciently. Bennett trim tabs decrease engine laboring,
which can improve fuel economy and prolong the life of the engine.
Maximize Performance While Smoothing Out The Ride: Bennett trim tabs
enhance the operating economy of your boat by lifting the stern in proportion to
speed, weight distribution, and fuel load changes–and AutoTrim Pro does this
automatically for you!
2Bennett Marine AutoTrim Pro | Need help? Call [phone]
Congratulations on your purchase! We're proud to say, boaters trust
our brand. After all, we invented the world’s rst adjustable trim
tab—and never stopped pushing forward, always striving to make a
better, more affordable system with maximum performance.

Contents
Contacting Us .................................................................................. 2
System Overview
System Overview............................................................................................... 4
System Components .......................................................................................... 5
Planning and Installation
Planning the Installation .................................................................................... 6
Installation of System Components ................................................................. 7
System Diagrams .............................................................................................. 10
ATP Helm Display Drilling Template ............................................................... 17
System Set-up & Calibration
Actuator Position Calibration ............................................................................ 20
Orientation Set-up.............................................................................................. 23
Angle Set-up ...................................................................................................... 24
Trim Tab Basics
How Trim Tabs Work......................................................................................... 28
Special Conditions & Safety ............................................................................ 30
AutoTrim Pro Operation
ATP Helm Display Quick-start Guide ............................................................... 32
Indication & Manual Mode Buttons ................................................................ 33
Semi-Automatic Controls ................................................................................ 35
Using Automatic Modes ................................................................................... 37
Understanding Automatic Operation ............................................................... 39
Troubleshooting
.................................................................................. 44
Warranty
.................................................................................................... 55

System Overview
AutoTrim Pro (ATP) is an all-in-one trim tab control system that packs a
boatload of essential features into an easy-to-use, space-saving keypad. This
system is a performance upgrade you can actually feel, engineered to make your
boating experience even more enjoyable.
AutoTrim Pro automatically levels the pitch and roll of your boat, adjusting your
trim tabs to hold the running angle you set throughout a variety of conditions
including vessel speed and shifting weight. Enjoy the convenience of riding in auto
mode, or shift to full manual mode anytime.
AutoTrim Pro (ATP) is an all-in-one trim tab control system consisting of two
components, the Helm Display and the Control Unit. The Helm Display inte-
grates four key functions: manual control, automatic control, trim tab position
indication, and automatic trim tab retraction. The ATP Control Unit is the “brain”
of the system which will constantly measure and monitor the boat's pitch and roll
attitude, operating the trim tab actuators accordingly.
Proper installation of the system components is critical for safe and optimal
operation of the system. The hydraulic ATP works with all standard Bennett
Marine trim tab systems including Classic, BXT, SST, and XPT.
AutoTrim Pro will work with classic Bennett pumps, dual classic pumps, or
dual high performance pumps. Because AutoTrim Pro is truly a control system,
the ATP can be combined with the appropriate power switching device and can
control many commercially available hydraulic trim tab systems, thus adding a
high degree of usability to any system.
All-in-one trim tab control system
AutoTrim Pro
4Bennett Marine AutoTrim Pro | Need help? Call [phone]

System Components
AutoTrim Pro
Helm Display
AutoTrim Pro
Control Unit
AutoTrim
Pro Kit Part#:
AP000A1HA
Optional port &
starboard sensor
adapter cables
Optional pump adapter cable
(Deutsch to Mate-n-lock)
25' Helm Display extension
Also included in the box
What's in the Box:
5
Bennett Marine AutoTrim Pro | Need help? Call [phone]

Getting Started
AutoTrim Pro requires the
presence of actuator sensor
wires in order to display trim
tab position indication LEDs
(although all other features will
function without sensors). Before
performing the installation, you
will need to determine if you
currently have sensors available,
and whether you will choose to
add or forgo sensor installation.
See the next "Checking for
Sensors" section to verify your
current system.
Installation of the ATP control
system will assume that the
installation of the trim tabs,
actuators, and wiring has been
previously completed according to
thier respective trim tab
installation and users guides which
can be downloaded at
BennettTrimTabs.com/Installation.
The ATP system contains the
following items:
1. ATP Helm Display
2. ATP Control Unit
3. Hardware and Cables
Additional components may be required
for more complex systems. Please call
Bennett Marine at [phone] with
any questions.
Checking for Sensors
Looking at which current Bennett
helm control you have will help
determine if you have sensors or not.
Adding Actuator Sensors
There are two options, you can
replace you current actuators with
new Bennett sensor-equipped
actuators, or you can simply swap
out the upper hinges of your existing
actuators with sensor-equipped upper
hinges–available as a conversion kit.
Call Bennett Marine at (954) 427-
1400 to order.
Planning The Installation
AutoTrim Pro is
equipped with tab
position indication
LED indicators.
For this feature
to work, actuator
sensors must be
present.
6Bennett Marine AutoTrim Pro | Need help? Call [phone]
VC1000 LS3000 ES2000
Sensors will be required
You have sensors already
IP1010A TPI2000 EIC5000

Installation of System Components
Installation of the ATP
Helm Display
Before starting any work, disconnect
the battery(s), and verify that all
power is turned off.
Preparation
Before installing the ATP Helm
Display, check for obstructions on
the underside of the helm. Locate an
appropriate location on the helm for
the ATP Helm Display. The ATP
Helm Display should be installed
such that the vessel operator has a
clear, unobstructed view of the
display, and is easily reachable from
the operating position. Ideally, the
ATP Helm Display should be
installed in a horizontal position.
This makes the use of the control
more intuitive. It is important for the
vessel operator to be able to clearly
see the LED indicators on the ATP
Helm Display to know what the ATP
is doing.
1. Use the template included on
Page 17 to help decide the
location for the ATP Helm
Display. The Helm Display
should be located on the helm in
view of the operator, and within
easy reach. It is important for
the vessel operator to be able to
clearly see the LED indicators on
the ATP Helm Display to know
what the ATP is doing. Before
installing the ATP Helm Display,
check for obstructions on the
underside of the helm.
2. Drill the center hole 1" using the
template from page 17.
3. Drill the four 3/16" screw holes.
4. Thread the wires for the ATP
Helm Display through the 1"
hole.
5. Secure the ATP Helm Display
using the four 8-32 nylon thumb
nuts included.
6. Locate the power source for all
of the helm instrumentation.
Connect the orange wire from the
ATP Helm Display to the power
source for the instrumentation.
When power is removed from this
orange wire, the system will shut
down.
7. Locate the ignition
power. Consult the engine
manufacturer’s documentation
to identify a source for ignition
power. Connect the purple wire
from the ATP display to the
7
Bennett Marine AutoTrim Pro | Need help? Call [phone]

ignition power. The ATP Helm
Control does not use any power
from the ignition system, but
senses when the power to the
ignition has been turned off to
automatically raise the trim tabs.
Note: The orange and purple
wire cannot be connected to the
same source. If the orange wire
is connected to the ignition, the
auto tab retract feature will not
function.
8. Locate a suitable ground. Connect
the black wire from the ATP Helm
Display to the ground source for
the instrumentation.
If a second helm station is utilized in
this system, repeat steps 1-5 only for
the upper station ATP Helm Display.
Installation of the ATP
Control Unit
The ATP Control Unit is the sensor
and processor for the ATP system
which activates the hydraulic
pumps that run the trim tabs. The
unit contains an accelerometer,
gyroscope, and an electronic
compass that sense the position
and movements of the boat and
therefore should not be mounted
within 24" of any magnetic items
such as electric motors or speakers.
However, the ATP Control Unit can
be conveniently mounted anywhere
in the boat, and in any orientation.
1. Locate a suitable dry, rigid
location for the ATP
Control Unit.
2. Mount the Control Unit
using the two #8 x ½" screws
provided.
3. Connect the orange and black
power wires to a power source
capable of supplying 20 Amps
@ 12V or 10 Amps at 24V.
(Refer to systems diagrams
beginning on page 10).
Connecting the System
1. Connect the communications
cable from the ATP Helm Display
to the communications cable on
the ATP Control Unit.
2. Connect the ATP Control Unit
to the 4-color wire harness
connector that is attached to the
hydraulic power unit. (Use the
provided adapter if needed).
If there are no sensors refer to
page 6 or call Bennett Marine at
954-427-1400.
3. If the boat has actuator sensors,
connect the port sensor cable to
the red sensor wire on the ATP
Control Unit. (Use the provided
adapter if needed). Connect the
starboard sensor cable to the
Installation of System Components continued
8Bennett Marine AutoTrim Pro | Need help? Call [phone]

continued Installation of System Components
green sensor wire on the ATP
Control Unit. (Use the provided
adapter if needed).
Testing the system
1. Reconnect the battery(s) or turn
the battery switch to ON.
2. Turn the ignition to the ON
position.
3. The ATP Helm Display should
illuminate, and all red tab position
LEDs should be ashing. This
indicates that the system needs
to be calibrated. If sensors are
properly installed (See page 6),
detection of the sensors will be
indicated by the upper yellow
LEDs on the Helm Control
continuously illuminated. Also the
2 green LEDs on the Control Unit
will be continuously illuminated.
4. The two blue LEDs over FAV1
and FAV2 should be ashing. This
is an indication that the system
has not yet been oriented to the
boat (You will complete this step
on page 23).
5. Press the PORT Bow DN button
on the ATP Helm Display. The
starboard actuator should extend.
If the starboard actuator does not
extend, or the port actuator
extends instead of the starboard
actuator, refer to the
troubleshooting section on
page 44.
6. Press the STBD Bow DN button
on the ATP Helm Display. The
port actuator should extend. If
the port actuator does not extend,
or the starboard actuator extends
instead of the port actuator, refer
to the troubleshooting section on
page 44.
9
Bennett Marine AutoTrim Pro | Need help? Call [phone]

System Diagrams
GROUND
GROUND
ORANGE WIRE
CONNECT TO HELM POWER
GROUND
PURPLE WIRE
CONNECT TO IGNITION
ORANGE WIRE
CONNECT TO 20A (12V)
10A (24V)
2
3
4
6
5
11
NO SENSOR CABLES
No. Part Name Description
1 ACT-XX Actuator
2 HPU-X Hydraulic Pump
3 RGYB-DPLG-DRPT-X Pump Extension Cable
4 ATPCTRLG4H ATP Module
5
ATPDISPLAYG4
Display
6 BQEDISEXTCABLE-X Display Extension Cable
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
Bennett Marine Inc. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE
WRITTEN PERMISSION OF
Bennett Marine Inc IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
NEXT ASSY
USED ON
APPLICATION
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/16
ANGULAR: MACH
BEND
TWO PLACE DECIMAL .01
THREE PLACE DECIMAL
.005
INTERPRET GEOMETRIC
TOLERANCING PER: ANSI Y-14
MATERIAL
FINISH
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
DATE
NAME
TITLE:
SIZE
B
DWG. NO.
REV
WEIGHT:
SCALE: 1:12
UNLESS OTHERWISE SPECIFIED:
Single Display
Single ACT
NO SENSORS
SHEET 9 OF 10
DO NOT SCALE DRAWING
Bennett Marine
550 Jim Moran Blvd
Deerfield Beach, FL 33442
Single Actuators
(No Sensor Wires)
Please call us at [phone] for
additional help with wiring instructions.
1. Actuator
2. Hydraulic Pump
3. Pump Extension Cable
4. Control Unit
5. ATP Helm Display
6. Helm Display Extension Cable
10 Bennett Marine AutoTrim Pro | Need help? Call [phone]

continued System Diagrams
ORANGE WIRE
CONNECT TO HELM POWER
PURPLE WIRE
CONNECT TO IGNITION
GROUND
GROUND
11 10
6
5
8
7
1 2
3
4
12 12
9
GROUND
ORANGE WIRE
CONNECT TO 20A (12V)
10A (24V)
No. PART NAME DESCRIPTION
1 ACT-XX PORT Actuator
2 ACT-XX STBD Actuator
3
SCBL22-S-DPLG-DRPT-X
STBD Sensor Extension Cable
4
SCBL22-P-DPLG-DRPT-X
PORT Sensor Extension Cable
5 ATPCTRLG4H ATP Module
6 BQEDISEXTCABLE-X Relay Module Extension Cable
7 HPU-XX Hydraulic Pump
8 RGYB-DPLG-DRPT-X Pump Extension Cable
9 ATP50-X Y-CABLE
10
ATPDISPLAYG4
Display
11 BQEDISEXTCABLE-X Display Extension Cable
12 BQEDISEXTCABLE-X Bridge Display Extension Cable
13
ATPDISPLAYG4-1
Bridge Display
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
Bennett Marine Inc. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE
WRITTEN PERMISSION OF
Bennett Marine Inc IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/16
ANGULAR: MACH
BEND
TWO PLACE DECIMAL .01
THREE PLACE DECIMAL
.005
INTERPRET GEOMETRIC
TOLERANCING PER: ANSI Y-14
DRAWN
DATE NAME
TITLE:
SIZE
B
DWG. NO.
REV
WEIGHT:
SCALE: 1:12
UNLESS OTHERWISE SPECIFIED:
SHEET 2 OF 10
ATP Single / Dual
DO NOT SCALE DRAWING
Bennett Marine
550 Jim Moran Blvd
Deerfield Beach, FL 33442
1. Port Actuator
2. Stbd. Actuator
3. *Stbd. Sensor Extension Cable
4. *Port Sensor Extension Cable
5. Control Unit
6. Control Unit Extension Cable
7. Hydraulic Pump
8. Pump Extension Cable
9. Y-Cable
10. ATP Helm Display
11. Bridge Helm Display
12. Bridge Display Extension Cable
* Optional
Dual Display
Hydraulic System
(With Sensor Wires)
Please call us at [phone] for
additional help with wiring instructions.
11
Bennett Marine AutoTrim Pro | Need help? Call [phone]

System Diagrams continued
Please call us at
[phone] for
additional help with
wiring instructions.
GROUND
GROUND
GROUND
GROUND
PURPLE WIRE
CONNECT TO IGNITION
ORANGE WIRE
CONNECT TO HELM POWER
ORANGE WIRE
CONNECT TO 20A (12V)
10A (24V)
1
1
4
5
11
6
3
2
9
9
7
10
88
ORANGE WIRE
CONNECT TO 20A (12V)
10A (24V)
GROUND
ORANGE WIRE
CONNECT TO
20A (12V)
10A (24V)
GROUND
NO. PART NAME DESCRIPTION
1 ACT-XX Actuator
2 ATPCTRLG4H ATP Module
3 HPU-XX PORT Hydraulic Pump
4 HPU-XX STBD Hydraulic Pump
5 RM-XX-YY STBD Relay Module
6 RM-XX-YY PORT Relay Module
7 ATP50-X Y Cable
8 BQEDISEXTCABLE-X Display Extension Cable
9
ATPDISPLAYG4
Display
10
ATPDISPLAYG4-1
Bridge Display
11 EICDPCABLE-XX-YY-ZZ Y-Harness
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/16
ANGULAR: MACH
BEND
TWO PLACE DECIMAL .01
THREE PLACE DECIMAL
.005
INTERPRET GEOMETRIC
TOLERANCING PER: ANSI Y-14
MATERIAL
FINISH
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
DATE
NAME
TITLE:
SIZE
B
DWG. NO.
REV
WEIGHT:
SCALE: 1:12
UNLESS OTHERWISE SPECIFIED:
Dual Display
Dual ACT
NO SENSORS
SHEET 10 OF 10
DO NOT SCALE DRAWING
Bennett Marine
550 Jim Moran Blvd
Deerfield Beach, FL 33442
Dual
Actuators
(No Sensor
Wires)
1. Actuators
2. Control Unit
3. Port Hydraulic Pump
4. Stbd. Hydraulic Pump
5. Stbd. Relay Module
6. Port Relay Module
7. Y-Cable
8. Helm Display Extension Cable
9. ATP Helm Display
10. Bridge ATP Helm Display
11. Y-Harness Cable
12 Bennett Marine AutoTrim Pro | Need help? Call [phone]

continued System Diagrams
Please call us at
[phone] for
additional help with
wiring instructions.
ORANGE WIRE
CONNECT TO 20A (12V)
10A (24V)
ORANGE WIRE
CONNECT TO HELM POWER
PURPLE WIRE
CONNECT TO IGNITION
GROUND
GROUND
GROUND
12
8 7
9
5
6
11 12
10
1314
4
3
66
GROUND
ORANGE WIRE
CONNECT TO
20A (12V)
10A (24V)
GROUND
ORANGE WIRE
CONNECT TO 20A (12V)
10A (24V)
GROUND
NO. PART NAME DESCRIPTION
1 ACT-XX PORT Actuators
2 ACT-XX STBD Actuators
3 SCBL22-S-DPLG-DRPT-X
STBD Sensor
Extension Cables
4 SCBL22-P-DPLG-DRPT-X
PORT Sensor
Extension Cables
5 ATPCTRLG4H ATP Module
6 BQEDISEXTCABLE-X
Display Extension
Cable
7 HPU-XX
STBD Hydraulic
Pump
8 HPU-XX
PORT Hydraulic
Pump
9 EICDPCABLE-XX-YY-ZZ Y-Harness Cable
10 RM-XX-YY STBD Relay Module
11 RM-XX-YY PORT Relay Module
12 ATP50-X Y-Cable
13 ATPDISPLAYG4 Display
14 ATPDisplayG4-1 Bridge Display
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/16
ANGULAR: MACH
BEND
TWO PLACE DECIMAL .01
THREE PLACE DECIMAL
.005
INTERPRET GEOMETRIC
TOLERANCING PER: ANSI Y-14
MATERIAL
FINISH
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
DATE
NAME
TITLE:
SIZE
B
DWG. NO.
REV
WEIGHT:
SCALE: 1:12
UNLESS OTHERWISE SPECIFIED:
SHEET 3 OF 10
ATP Dual / Dual
DO NOT SCALE DRAWING
Bennett Marine
550 Jim Moran Blvd
Deerfield Beach, FL 33442
Classic
Dual Pump
Hydraulic
System (With
Sensor Wires)
1. Port Actuators
2. Stbd. Actuators
3. *Stbd. Sensor Extension Cable
4. *Port Sensor Extension Cable
5. ATP Control Unit
6. Helm Display Extension Cable
7. Stbd. Hydraulic Pump
8. Port Hydraulic Pump
9. Y-Harness Cable
10. Stbd. Relay Module
11. Port Relay Module
12. Y-Cable
13. ATP Helm Display
14. ATP Bridge Helm Display
* Optional
13
Bennett Marine AutoTrim Pro | Need help? Call [phone]

System Diagrams continued
9
3
4
ORANGE WIRE
CONNECT TO 20A (12V)
10A (24V)
ORANGE WIRE
CONNECT TO HELM POWER
PURPLE WIRE
CONNECT TO IGNITION
GROUND
GROUND
GROUND
11
8
12
6
710
12
5
GROUND
ORANGE WIRE
CONNECT TO
20A (12V)
10A (24V)
ORANGE WIRE
CONNECT TO
20A (12V)
10A (24V)
No. PART NAME DESCRIPTION
1 BXA-XX / SSA-XX PORT Actuator
2 BXA-XX / SSA-XX STBD Actuator
3 SCBL22-S-DPLG-DRPT-X
STBD Sensor
Extension Cable
4 SCBL22-P-DPLG-DRPT-X
PORT Sensor
Extension Cable
5 ATPCTRLG4H ATP Module
6 HPU-OIL-XX STBD Hydraulic Pump
7 HPU-OIL-XX
PORT Hydraulic
Pump
8 EICDPCABLE-XX-YY-ZZ Y-Harness Cable
9 GYB-DRPT-DPIN-P-X STBD Pump Extension
Cable
10 RYB-DRPT-DPIN-P-X
PORT Pump
Extension Cable
11 BQEDISPCABLE-X
Display Extension
Cable
12 ATPDISPLAYG4 Display
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
Bennett Marine Inc. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE
WRITTEN PERMISSION OF
Bennett Marine Inc IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
DATE
NAME
TITLE:
SIZE
B
DWG. NO.
REV
WEIGHT:
SCALE: 1:12
ATP BXA
Single Display
SHEET 6 OF 10
Bennett Marine
550 Jim Moran Blvd
Deerfield Beach, FL 33442
Oildyne
Dual Pump
Single Helm
Display
System (With
Sensor Wires)
1. Port Actuator
2. Stbd. Actuator
3. *Stbd. Sensor Extension Cable
4. *Port Sensor Extension Cable
5. Control Unit
6. Stbd. Oildyne Hydraulic Pump
7. Port Oildyne Hydraulic Pump
8. Y-Harness Cable
9. Stbd. Pump Extension Cable
10. Port Pump Extension Cable
11. Display Extension Cable
12. Helm Display
* Optional
Please call us at
[phone] for
additional help with
wiring instructions.
14 Bennett Marine AutoTrim Pro | Need help? Call [phone]

continued System Diagrams
9
6
GROUND
GROUND
GROUND
PURPLE WIRE
CONNECT TO IGNITION
ORANGE WIRE
CONNECT TO HELM POWER
ORANGE WIRE
CONNECT TO 20A (12V)
10A (24V)
12
8
12
7
5
13
14
43
66
10
11
GROUND
ORANGE WIRE
CONNECT TO
20A (12V)
10A (24V)
ORANGE WIRE
CONNECT TO
20A (12V)
10A (24V)
No. Part Name DESCRIPTION
1 BXA-XX / SSA-XX PORT Actuator
2 BXA-XX / SSA-XX STBD Actuator
3
SCBL22-S-DPLG-DRPT-X
STBD Sensor Extension
Cable
4
SCBL22-P-DPLG-DRPT-X
PORT Sensor Extension
Cable
5 ATPCTRLG4H ATP Module
6 BQEDISPCABLE-X
Relay Module
Extension Cable
7 HPU-OIL-XX
STBD Dual Acting
Hydraulic Pump
8 HPU-OIL-XX
PORT Dual Acting
Hydraulic Pump
9 EICDPCABLE-XX-YY-ZZ Y-Harness Cable
10
GYB-DRPT-DPIN-P-XB3
STBD Pump Extension
Cable
11 RYB-DRPT-DPIN-P-X
PORT Pump Extension
Cable
12 ATP50-X Y-Cable
13
ATPDISPLAYG4
Display
14
ATPDISPLAYG4-1
Bridge Display
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
Bennett Marine Inc. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE
WRITTEN PERMISSION OF
Bennett Marine Inc IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
DATE
NAME
TITLE:
SIZE
B
DWG. NO.
REV
WEIGHT:
SCALE: 1:12
SHEET 5 OF 10
ATP OIL / BXA
Bennett Marine
550 Jim Moran Blvd
Deerfield Beach, FL 33442
Oildyne
Dual Pump
Dual Helm
Display
System (With
Sensor Wires)
1. Port Actuator
2. Stbd. Actuator
3. *Stbd. Sensor Extension Cable
4. *Port Sensor Extension Cable
5. Control Unit
6. Extension Cable
7. Stbd. Oildyne Hydraulic Pump
8. Port Oildyne Hydraulic Pump
9. Y-Harness Cable
10. Stbd. Pump Extension Cable
11. Port Pump Extension Cable
12. Y-Cable
13. Helm Display
14. Bridge Helm Display
* Optional
Please call us at
[phone] for
additional help with
wiring instructions.
15
Bennett Marine AutoTrim Pro | Need help? Call [phone]

System Diagrams continued
ORANGE WIRE
CONNECT TO 20A (12V)
10A (24V)
ORANGE WIRE
CONNECT TO HELM POWER
PURPLE WIRE
CONNECT TO IGNITION
GROUND
GROUND
GROUND
12
5
8
6
9
7
10
11
12
4 3
GROUND
ORANGE WIRE
CONNECT TO 20A (12V)
10A (24V)
GROUND
ORANGE WIRE
CONNECT TO
20A (12V)
10A (24V)
GROUND
No. PART NAME DESCRIPTION
1 BXA-XX/SSA-XX PORT Actuator
2 BXA-XX/SSA-XX STBD Actuator
3
SCBL22-S-DPLG-DRPT-X
STBD Sensor Extension
Cable
4
SCBL22-P-DPLG-DRPT-X
PORT Sensor Extension
Cable
5 ATPCTRLG4H ATP Module
6 BQEDISEXTCABLE-X Display Extension Cable
7 HPU-XX STBD Hydrualic Pump
8 HPU-XX PORT Hydraulic Pump
9 EICDPCABLE-XX-YY-ZZ Y-Harness Cable
10 RM-XX-YY STBD Relay Module
11 RM-XX-YY PORT Relay Module
12
ATPDISPLAYG4
Display
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/16
ANGULAR: MACH
BEND
TWO PLACE DECIMAL .01
THREE PLACE DECIMAL
.005
INTERPRET GEOMETRIC
TOLERANCING PER: ANSI Y-14
MATERIAL
FINISH
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
DATE
NAME
TITLE:
SIZE
B
DWG. NO.
REV
WEIGHT:
SCALE: 1:12
UNLESS OTHERWISE SPECIFIED:
SHEET 8 OF 10
ATP HPUDA BXA
Single Display
DO NOT SCALE DRAWING
Bennett Marine
550 Jim Moran Blvd
Deerfield Beach, FL 33442
Dual Acting Pump
with BXA Actuator
(With Sensor Wires)
1. Port Actuator
2. Stbd. Actuator
3. *Stbd. Sensor Extension Cable
4. *Port Sensor Extension Cable
5. Control Unit
6. Control Unit Extension Cable
7. Stbd. Dual Acting Pump
8. Port Dual Acting Pump
9. Y-harness Cable
10. Stbd. Relay Module
11. Port Relay Module
12. ATP Helm Display
* Optional
Please call us at [phone] for
additional help with wiring instructions.
16 Bennett Marine AutoTrim Pro | Need help? Call [phone]

2.13
2.13
1"
1.00
3/16"
ATP Helm Display Drilling Template
Verify template dimensions if
printed from the web or copied
Must be printed or
copied at 100% scale
1"
17
Bennett Marine AutoTrim Pro | Need help? Call [phone]

18 Bennett Marine AutoTrim Pro | Need help? Call [phone]

AutoTrim Pro System Set-up
Actuator Position Calibration
Calibrating Systems with Sensors...................................................................... 20
Disabling the LED Alert for Systems Without Sensors .................................... 22
Orientation & Angle Set-up
Orientation Set-up.............................................................................................. 23
Angle Set-up ...................................................................................................... 24
19
Bennett Marine AutoTrim Pro | Need help? Call [phone]

System Set Up: Actuator Position Calibration
This step should be completed before the boat is launched
Actuator Position Calibration With Sensors
See page 22 for set-up if sensors are NOT present. See page 6 to learn about
the purpose of sensors and to determine if you currently have sensors or not.
The red tab position LEDs on the Helm Display should be ashing alternately
PORT and STBD. This is the system’s indication that there is no actuator
calibration stored yet.
1. If the upper yellow LEDs are
ashing, the system does not
detect the presence of sensors in
the actuators. Check to make sure
the red and green sensor cables are
connected to the ATP Control
Unit. If the system does not have
actuator sensors, skip to page 22.
2. Press and hold the bright (Sun)
and dim (Moon) buttons
simultaneously for about three
seconds. This will enter the
system into calibration mode.
The lower two yellow LEDs
should begin to ash.
3. Press and hold both Bow DN
buttons until both actuators are
fully extended.
4. After a few seconds, the upper two
yellow LEDs should begin to ash.
20 Bennett Marine AutoTrim Pro | Need help? Call [phone]