Bensons for Beds HIP HOP STK268005 User manual

Regrettably self-assembly items cannot be returned once assembly is part or fully completed
unless the items are found to be faulty. Should you need to return the unassembled product,
please repack in its original packaging.
Important information
— We suggest you spend a short time reading through this leaflet and then follow the simple
step-by-step instructions.
— Carefully check that you have all the parts before beginning assembly.
— Keep fittings out of children's reach and keep children well away from construction area.
— We suggest you retain these instructions for future reference.
— In the unusual event of an issue with your product would you please quote the batch I.D.
number situated on the main parts of the frame.
Product information
— Product finished Painted White finish.
— 2 Door & 2 Drawer.
— Conforms to BS EN14749 & BS4875-7 Standard
Care instructions
— Avoid exposing the furniture to excessive heat or direct sunlight as this can cause cracking and
deterioration of the color.
— Periodically check & re-tighten any fastener.
— Periodically dust lightly with a clean soft cloth.
— Do not use silicone based furniture polish.
— Any spills should be removed immediately with a damp cloth.
— TAKE CARE WHEN MOVING THE FURNITURE AND NEVER DRAG THE PIECES ACROSS
THE FLOOR, AS THIS WILL CAUSE DAMAGE TO THE JOINTS
Page<1/6>
2 DOOR +2 DRAWER HIP HOP WARDROBE WHITE
STK268005
Assembly instructions
Please keep these instructions for future reference.
Minimum Two
Persons Assembly
Approximate
Assembly Time
50 MIN

Component of Carton A Component of Carton B
(1) Side panel (R&L)2
Hardware List
(A) Ø4 16 Screw
66 (B) Ø8 Dowel
22 (C) M645 Bolt
8
(M) Hanger rail support
2
(H) Locking Pin
14
(I) Locking Nut
14 (J) Concealed Hinges
6
(2) Door(R)
(4) Back Panel
(13) Back support rail
(11) Front support rail
(12) Drawer side panel
(R&L)
(5) Drawer back
(14) Drawer front panel
(K) Ø3.516 Screw
2
Page <2/6>
(Q) 4MM Wrench
1
(P) Nylon braid
2
(D) M635 Bolt
4
(E) Ø3 16 Screw(zinc)
14
(L) Ø4 30 Screw
10
(N) Ø6 Washer
12 (O) Ø6 Dowel
12
(G) Magnetic Catche
4
(F) Magnetic Catche
2
(3) Door(L)
(7) Top Panel
(8) Shelf
(9) Bottom Panel
(10) Hanger Rail
(15) Drawer bottom
support
(16) Drawer bottom
panel
(6) Batten
2Door -2Drawer Wardrobe
(R) Ø3 14 Screw (black)
6
白色2021-6-13(新LOGO)

Page <3/6>
A
H
H
H
H
H
I
C
NB
B
Step 1
Step 2
A
EF
EF
E
F
B
B
C
N
Q
MM
Front
Front
1L 1R
7
8
1L
1R
8
9
13
X4
X4
Back
Back
13
11
11
E
F
Step 1
Step 2
13

AE
E
R
R
A
A
A
AJ
J
J
J
J
Step 3
Step5
D
B
DB
B
Q
G
G
G
7
2
3
6
X2
J
A
X3X3R
E
R
E
A
AA
4
Step4
G
Page <4/6>
UP

Page <5/6>
10
10
L
L
O
H
H
H
LI
IO
Step6 Step7
Step8 Step9
Step10
Door
Carcass
A
A
5
12L
12R
16
14 15
14
2
3
X6
X2

Page <6/6>
Hole in the
Wall NOT
PROVIDED NOT
PROVIDED
Step 12
Step11
K
P
WARNING:
To prevent your furniture from tilting forward and possibly causing property damage or personal injury it is recommended
that youSecurely attach the safety strap provided to your wall using appropriate fixings
IMPORTANT:
—DO NOTplace toys or other child appealing items on top of this furniture
—AVOIDfully opening all drawers at the same time
—DO NOT ALLOWSmall children to climb onto Drawers, shelves or to swing from open doors
CAUTION:
For your safety when attaching the anti-tilt fixings;
—Check for any electrical wires or plumbing inside the wall before drilling any holes (if you are unsure please seek
professional advice from a qualified tradesman)
— Walls are constructed from different materials eg: Masonry ( solid brick) or plaster board lined cavity walls (hollow).
It is important that you use the appropriate wall fixings for your wall type.
(Your local hardware store will have the necessary drills and fixings and can offer advice if needed)
X2
X2
N
N

Assembly Instructions
Hinge Adjustment
Lateral Movement
How to fix it
- To move the door towards the centre of the unit,
loosen Screw "A". Adjust the door and then tighten
Screw "B".
- To move the door away from the centre of the unit, loosen
Screw "B". Adjust the door and then tighten Screw "A".
What it looks like
- The door will not be flush with the side panel.
What it looks like
- The door will not be flush with the vertical panel.
Vertical Movement
Horizontal Movement
What it looks like
- The door will appear too far or too close from
the front edge of the side panel.
How to fix it
- To move the door towards or away from the horizontal panels,
loosen Screws "C". Adjust the door and then tighten Screws "C".
How to fix it
- To move the door towards or away fron the unit, loosen Screw
"A". Adjust the door forwards or backwards until there is an even
gap between the door and the front edge of the side panel.
- Tighten Screw "A" once the adjustment has been made.
Door
Carcass
Screw"A"
Screw"B"
Door
Carcass
Screw"C"
Screw"C"
Door
Carcass
Screw"A"