Bensons for Beds San Diego HUB120300 User manual

Regrettably self-assembly items cannot be returned once assembly is part or fully completed
unless the items are found to be faulty. Should you need to return the unassembled product,
please repack in its original packaging.
Important information
— We suggest you spend a short time reading through this leaflet and then follow the simple
step-by-step instructions.
— Carefully check that you have all the parts before beginning assembly.
— Keep fittings out of children's reach and keep children well away from construction area.
— We suggest you retain these instructions for future reference.
— In the unusual event of an issue with your product would you please quote the batch I.D.
number situated on the main parts of the frame (Head End- Foot End- side Rails).
Product information
— Upholstered Bed Using Fabric Material. Conforms to BS EN1725 & BS 5852
Care instructions
— Avoid exposing the furniture to excessive heat or direct sunlight as this can cause cracking and
deterioration of the color.
— Periodically check & re-tighten any fastener.
— Periodically dust lightly with a clean soft cloth.
— Do not use silicone based furniture polish.
— Any spills should be removed immediately with a damp cloth.
— TAKE CARE WHEN MOVING THE FURNITURE AND NEVER DRAG THE PIECES ACROSS
THE FLOOR, AS THIS WILL CAUSE DAMAGE TO THE JOINTS
Page<1/5>
Assembly instructions
Please keep these instructions for future reference.
San Diego Bedstead / 120cm&135cm&150cm&180cm
HUB120300/HUB120200/HUB135300/HUB135200/HUB150300/HUB150200/HUB180300/HUB180200
Minimum Two
Persons Assembly
Approximate
Assembly Time
60 MIN

Component of Carton A Component of Carton C
(1) Head Board1
Hardware List
(A) M8 40 Bolt
4
(J) 4MM Allen key
2(K) 5MM Allen key
1
(2) Foot Board1
(4) Side Rail (R&L)2
(5) Shelf rail / long1
(7) Support Leg / long2
(8) Support Leg / short2
(10) Bed Base1
(9) Lifting arms (R&L)2
(E)
14" Jcn Nut
2(F) M10 Connecting bolt
2
(6) Shelf rail / short2
Component of Carton D
(11) Shelf4
Samll Double: 120cm190cm /Double: 135cm190cm /King: 150cm200cm / Super- king : 180cm200cm
Component of Carton B
(B) M825 Bolt
6(C) M820 Bolt
18
LOOSEN
LOOSEN
K
K
12
Step1
(I) Nut
2
Page<2/5>
(L) Spanner
1
(3) Foot2
(D)
14"34" Bolt
10
(G) Ø8 Washer
6(H) Ø8 Spring Washer 6
G
H
B
A
3
A
Pre-installed in Foot end

Step3
Page<3/5>
4(L)
4(R)
6
Step2
5DD
D
D
D
D
D
E6
65
J
D
D
5
J
Do not tighten the bolt fully
until the bolts of part 5 are
fixed to head board and
foot board.
J

Step4
Step5
Page<4/5>
F
F
7
7
8
8
9(L) C
C
C
C
NOTES: Attach cylinders to lifting arms
by using nut "I" as shown below.
9(R)
9(L) L
I
I
CC
F
7
8
IL
C
9(R)
C
C
C
C
9(R)

Step7
Page<5/5>
Step 6
C
C
C
C
C
C
C
C
C
10
11
11
11
11
C
"IMPORTANT NOTICE"
---WARNING: PLEASE DO NOT ALLOW CHILDREN OR PETS INSIDE THE
STORAGE AREA.
---WARNING: PLEASE BE CAREFUL WHEN LIFTING.
ONLY LIFT WITH MATTRESS ON TOP.
TO BE OPERATED BY ADULTS ONLY.
---WARNING: PLEASE DO NOT PRESS DOWN ON THE MATTRESS WHEN
THE BED FRAME IS IN THE LIFT UP POSITION.
---WARNING: THE BED FRAME TOP MUST ONLY BE CLOSED BY USING TWO
HANDS EQUALLY SPACED FROM THE CENTER OF THE
MATTRESS BASE.
Use the strap handle to lift up the mattress base using two hands
Pull the mattress base down using two hands equally spaced from
the center of the mattress base. DO NOT pull down on one side of
base only as this is likely to damage the base system with potential
failure of the mattress base system and lift mechanism.
PULL DOWN
C
C
C
C