Bensons for Beds MADDISON STK800001 Datasheet

Page 1 of 9
MADDISON BED 120 / 135 / 150 cm
Assembly lnstructlons
Please keep these lnstructlons for future reference.
P.O.Number :
Please Keep This Number For
Future Reference
THIS FORMS PARTS OF
YOUR GUARANTEE!
Regrettably self-assembly items cannot be returned once assembly is part or fully completed unless the
items are found to be faulty.Should you need to return the un assembled product, please repack in its original
packaging.
lmportant Information
● We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
● Carefully check that you have all the parts before beginning assembly.
● Keep fittings out of children's reach and keep children well away from construction area.
● We suggest you retain these instructions for future reference.
Care Instructions
● Avoid exposing the furniture to excessive heat or direct sunlight as this can cause cracking or
deterioration of the color.
● Periodically check & re-tighten any screws and fixings.
● Periodically dust lightly with a clean soft cloth.
● TAKE CARE WHEN MOVING THE FURNITURE AND NEVER DRAG THE PIECES ACROSS
THE FLOOR,AS THIS WILL CAUSE DAMAGE TO THE JOINTS.
Frame Tested To BSEN1725
Fabrics and filings to BS5852
1 Hr
Product Details
STK800001 4' Bed Dark Grey
STK800002 4'6 Bed Dark Grey
STK800003 5' Bed Dark Grey
Approximate
Assembly Time
(REV 03 12/12/2023)
Minimum two
person assembly

Tips before you start!
1. Please check that all parts are present before you start the assembly of your furniture.
2. For ease and speed of assembly, we recommend that before you commence each step of the
assembly, that you identify all the parts required for that step.
3. For larger items, please ensure that you have sufficient space and people (as indicated on page
1) to assemble your product safely. (Minimum Two Persons)
4. We recommend where possible, all items are assembled near to the area where they will be
used, to avoid moving the product unnecessarily once assembled.
5. Please ensure that your bed is placed on a level floor area. (Avoid setting up and installing your
bed on uneven floor surface)
6. For the protection of your furniture, we recommend that the product is placed on a protected
surface during assembly to prevent any damage.
7. During assembly please take care not to over-tighten any fittings, as this may damage the
product.
Care and Maintenance of your Furniture
● Please periodically check all fittings and re-tighten as necessary.
● To clean your item, please use a soft damp cloth and wipe clean.
● Please do not jump on your furniture.
● Never allow any kind of liquid to remain on your furniture. This can cause finishes to de-laminate.
Take care when spraying Perfume and deodorants etc as the vapour can settle on the surface
and cause damage.
● Periodically check the condition of your bed slats to ensure they are in good condition and have
not become loose.
● It is important to never drag your bed as this can cause damage to the joints and the fixings. This
may invalidate your guarantee.
● The bed should always be lifted into position or if moved for cleaning. Do not attempt to drag the
bed across the floor.
● Periodically check the central support legs are perfectly upright and supporting the centre rail.
Page 2 of 9(REV 03 12/12/2023)

Components
A Headboard x 1
(4'-1230 x 600mm)
(4'6-1380 x 600mm)
(5'-1530 x 600mm)
B Foot End x 1
(4'-1225 x 335mm)
(4'6-1375 x 335mm)
(5'-1525 x 335mm)
C Side Rail x 2
(4'/4'6-40 x 1900mm)
(5'-40 x 2000mm)
D Central Support System
x 1
(4'/4'6-25 x 1770mm)
(5'-25 x 1910mm)
E Cross Stretcher x 1
(4'-40 x 1180mm)
(4'6-40 x 1330mm)
(5'-40 x 1480mm)
F Slatted System x 2
(4'-14 x 45 x 1180mm x 8 slats)
(4'6-14 x 45 x 1330mm x 8 slats)
(5'-14 x 45 x 1480mm x 9 slats)
G Headboard Leg
(Left) x 1
(25 x 40 x 445mm)
H Headboard Leg
(Right) x 1
(25 x 40 x 445mm)
Page 3 of 9
Hardware List
K M6 x 15mm
x 8
P M6 x 16mm
x 23
Q M6 x 10mm
x 6
L M6 x 30mm
x 4
M M6 x 35mm
x 6
J Allen Key (M4)
x 1
N M6 x 40mm
x 6
O M6 x 60mm
x 3
(REV 03 12/12/2023)

Step 1
● Pull straps to remove transit blocks.
K x 4
J x 1 P x 4 Q x 4
A
A
G
G
H
J
K
P
Q
Page 4 of 9
Pull to
remove
A
Step 2
● Attach headboard legs using the fixings as shown.
A
Rear
Rear
Required Fixings for this step.
(REV 03 12/12/2023)

Step 3
● With help, carefully turn the headboard over.
● Insert fixings and as shown, but leave loose.
● Repeat this step on the foot end.
Step 4
● Unfold and extend the side rails.
K x 4 P x 4
A
A
B
B
C
C
C
C
K
P
P
K
Page 5 of 9
Leave screws loose
K P
X2
Required Fixings for this step.
(REV 03 12/12/2023)

Ensure frame is square
before tightening fixings
Step 5
● Slide the side rail bracket over the inserted screw in the headboard and foot end as shown.
Step 6
● Ensure the frame is square.
● Secure at the back of the headboard using fixings , and .
● Secure at the front of the foot end using fixings and .
● Tighten ALL fixings including the ones from previous steps .
J x 1
O x 2
J x 1 P x 4 Q x 2
N x 2
A
A
B
B
B
B
C
C
C
C
C
C
C
C
J
J
N
O
P
P
Q
Page 6 of 9
PK
PK
Leave fixings loose
OP Q
N P
Required Fixings for this step.
Required Fixings for this step.
(REV 03 12/12/2023)

Step 7
● Unfold and extend the central support system .
● Secure legs using fixings and as shown.
Step 8
● Attach the cross stretcher as shown taking extra care to ensure the arrows are pointing
upwards as shown.
J x 1 P x 4M x 4
D
D
D
D
J
M
P
Page 7 of 9
C
C
C
E
E
J
N
J x 1 N x 4
up
Arrow label
to face up
D
MP
D
Required Fixings for this step.
Required Fixings for this step.
(REV 03 12/12/2023)

Step 9
● Position central support system and secure as shown.
J x 1 O x 1
D
D
E
E
J
O
Page 8 of 9
P x 1
P
Required Fixings for this step.
(REV 03 12/12/2023)

Step 10
● As shown fix the first slat of the slatted system (with cut outs) to the side rails using the fixings
as shown.
● Fixings and are used at each end of the wooden slat. Fixings and are used in the
centre of the wooden slat.
● Gently pull each slat to extend the velcro strip and firmly push the slat down to create the
connection between the two fabrics.
J x 1 L x 4 M x 2 P x 6
Page 9 of 9
a：
D
F
J
M
P
b：
C
F
J
L
P
a：
D
F
J
M
P
b：
C
F
J
L
P
c：
C
F
J
L
P
C：
C
F
J
L
P
Repeat for the Second slatted system working from the foot end inward.
F
Pull
Pull F
L P M P
Required Fixings for this step.
(REV 03 12/12/2023)