2 Rev. 1.3 25/06/2015
O
PERATING
M
ODE WITH
R
EMOTE
C
ONTROLS
,
T
AG
R
EADER
,
K
EYBOARD
AND
/
OR
NFC
R
EADER
The receiver can be combined with Remote Controls, TAG Reader,
Keyboard and/or NFC Reader and stores up to 1000 different users.
We recommend you write down the corresponding "storage position -
user name".
For use with remote controls, the receiver unit is equipped with an in-
corporated receiver; for use with other devices, the desired accessory
must be connected (by carefully following the connection diagrams de-
scribed in the relative operating manuals) supplied as optionals.
D
ATE
/T
IME
S
ETTING
The receiver is equipped with a clock with buffer battery that allocates a
time reference to each operation.
Proceed as follows to enter the date and time:
Date settings : use the UP or DOWN button to go to the DATE storage
position and press SEL and SET: Digits 2, 3 and 4 will start flashing, at
the same time use the UP or DOWN button to select a day of the week
between MON and SUN then press SET to confirm
(STOR will be dis-
played); next, Digits 1 and 2 will start flashing, at the same time use the
UP or DOWN button to select a number between 01 and 31 to choose
the day and press SET to confirm
(STOR will be displayed); next, Digits
3 and 4 will start flashing, at the same time use the UP or DOWN but-
ton to select a number between 01 and 12 to choose the month and
press SET to confirm (STOR will be displayed); next, all Digits 1,2,3
and 4 will start flashing, at the same time use the UP or DOWN button
to select a number between 14 and 99 to choose the year and press
SET to confirm (STOR will be displayed), thus completing the opera-
tion.
Time settings : use the UP or DOWN button to go to the TIME storage
position and press SEL and SET: Digits 1 and 2 will start flashing, at
the same time use the UP or DOWN button to select a number be-
tween 00 and 23 to choose the hour and press SET to confirm (STOR
will be displayed); next, Digits 3 and 4 will start flashing, at the same
time use the UP or DOWN button to select a number between 00 and
59 to choose the minutes and press SET to confirm (STOR will be dis-
played), thus completing the operation.
P
ROGRAMMING OF
R
EMOTE
C
ONTROLS
,
T
AG
R
EADER
,
K
EYBOARD
AND
/
OR
NFC
R
EADER
Programming of the Remote Controls, TAG Reader, Keyboard and/or
NFC Reader is the self-learning type and is performed as follows: use
the UP or DOWN button to go to the desired storage position (shown
on the display from 0001 to 0999) paying attention to the KEYBOARD,
NFC DEVICE, REMOTE CTR and TAG DEVICE LEDs since the light-
ing up of one of these four means that the location selected is occu-
pied. Press SEL, all of the LEDs will start flashing and at the same time
send the code with the Remote Control or move the Transponder close
to the TAG Reader or digit an access code on the KEYBOARD or move
the Smartphone close to the NFC Reader. STOR will be displayed and
the LED of the corresponding Device will switch from off to on, thus
completing the operation.
To delete a Device previously stored, using the UP or DOWN button go
to the location of the occupied storage position, press SEL, one of the
four corresponding KEYBOARD, NFC DEVICE, REMOTE CTR and
TAG DEVICE LEDs will start flashing; press SET, the display will show
"DELE" deleted and the LED will switch from on to off, thus completing
the operation.
Q
UICK
P
ROGRAMMING OF
R
ADIO
C
ONTROLS
,
T
AG
R
EADER
,
K
EYBOARD
AND
/
OR
NFC
R
EADER
Quick programming of the Remote Controls, TAG Reader, Keyboard
and/or NFC Reader is allowed only when the receiver's entire memory
is free. To make sure that the entire memory is free, follow the Reset
procedure.
Quick programming permits you to not select a new storage location
every time for an additional Device, but starting from position 0001 the
control unit automatically increases the storage location and remains in
standby for 15 seconds from entering a new Device to be stored.
O
VERALL
O
PERATION
T
IME
S
LOT
(
TSTA
;
TSTO
)
With the receiver you can program a daily operation time slot for activa-
tion only at a pre-set time.
Proceed as follows to choose the operation starting time: use the UP or
DOWN button to go to the TSTA storage position and press SEL and
SET. Digits 1 and 2 will start flashing, at the same time use the UP or
DOWN button to select a number between 00 and 23 to choose the
operation starting hour and press SET to confirm (STOR will be dis-
played); next, Digits 3 and 4 will start flashing, at the same time use the
UP or DOWN button to select a number between 00 and 59 to choose
the minutes and press SET to confirm (STOR will be displayed), thus
completing the operation.
Proceed as follows to choose the operation ending time: use the UP or
DOWN button to go to the TSTO storage position and press SEL and
SET. Digits 1 and 2 will start flashing, at the same time use the UP or
DOWN button to select a number between 00 and 23 to choose the
operation ending hour and press SET to confirm (STOR will be dis-
played); next, Digits 3 and 4 will start flashing, at the same time use the
UP or DOWN button to select a number between 00 and 59 to choose
the minutes and press SET to confirm (STOR will be displayed), thus
completing the operation.
NOTE: the Devices stored in the storage positions between 0950 and
0999 are not subject to the Time Slot function.
O
VERALL
A
NTI
P
ASS
-B
ACK
F
UNCTION
(
BACK
)
With the receiver you can select the Anti Pass-Back function (default =
OFF), i.e. using a couple of TAG Readers, Keyboards and/or NFC
Readers (with different operation addresses set between them) once
you have accessed, you will need to exit the reserved area before ac-
cessing again. This operation can be limited also for the Number of ac-
cesses or for its duration.
Proceed as follows to select the Anti Pass-Back function: use the UP or
DOWN button to go to the BACK storage position and press SEL and
SET: all Digits will start flashing, at the same time use the UP or
DOWN button to select one of the following codes OFF or ON-1, ON-2,
press SET to confirm (STOR will be displayed); next, all Digits will start
flashing, at the same time use the UP or DOWN button to select a
number between N000 (N000 = all can access) and N949 for the
maximum number allowed who can access the reserved area, then
press SET to confirm
(STOR will be displayed); next, all Digits will start
flashing, at the same time use the UP or DOWN button to select a time
between T000 minutes (000 = time excluded) and T999 minutes for the
maximum time allowed for remaining within the reserved area and
press SET to confirm
(STOR will be displayed), thus completing the
operation.
When selecting the Anti Pass-Back ON-1 function, you must always
enter and exit from the same access controlled by OUT 1 output.
Consequently the OUT 2 output can be used for connecting a traffic
light (Red/Green) indicator, for information on ramp momentarily busy
or number of parking spaces still available up to the limits set.
When selecting the Anti Pass-Back ON-2 function, you must always
enter from the access controlled by the OUT1 relay and always exit
from the access controlled by the OUT2 relay.
NOTE: The Anti Pass-Back function does not allow access via Remote
Control.
NOTE: The Anti Pass-Back function is not allowed if the OUT1 Bistable
mode was previously activated.
NOTE: The Anti Pass-Back function through the use of connected Key-
boards foresees that the devices have the ability to send the same se-
rial code but with different addresses set (one for input and the other for
output), and at least a complete passage was carried out during instal-
lation.
NOTE: the Devices stored in the storage positions between 0950 and
0999 are not subject to the Anti Pass-Back function.
R
ELAY
O
UTPUT
O
PERATION
(
OUT
1
)
With the receiver you can select the Monostable or Bistable OUT1 relay
output operating mode.
The Monostable operation (default), at each transit, activates the OUT1
relay for 1 second. With the Bistable operation, a first transit activates
the OUT1 relay, the next transit deactivates it.
Proceed as follows to select the desired operating mode: use the UP or
DOWN button to go to the OUT1 storage position and press SEL and
SET: all Digits will start flashing, at the same time use the UP or
DOWN button to select one of the following codes MONO = Monosta-
ble or BIST = Bistable, press SET to confirm (STOR will show on the
display), thus completing the operation.
NOTE: at every OUT1 relay activation transit, the corresponding num-
ber stored will be displayed for a few seconds.
NOTE: The OUT1 Bistable mode is not allowed if the Anti Pass-Back
function was previously activated.
