A.Features
B.Dimension
Dimension
Diameter
DN10
DN15
DN20
DN25
DN32
DN40
Screwed Type Ball Valve Wafer Butterfly Valve
L×W×H
(A×B1×H） Conneciton End
55×53×11 5
62×53×11 7
75×53×12 0
35×85×20 0
35×85×20 0
35×85×21 0
Rc3/ 4 "
Rc1/ 2 "
Wafer
Wafer
Wafer
L×W×H
(A×B2×H）
Rc3/ 8 "
Unit:mm
1. Small size, light weight, exquisite appearance, cheaper than C800 series
2. With emergency manual device
3. Motor with protection device, when locked-rotor happened,
power off automatically
4. With visual valve position indicator
5. Can be mounted at any angle
6. With valve position signal output ( passive output-contact/NPN transistor )
7. Butterfly valve body: normal--- CAST Steel WCB(code: C)
Ball valve body: Normal --- 304 stainless steel ( code: B),
Special --- 316 stainless steel (code: R),
316L stainless steel ( code: L)
8.Seal material : Butterfly--- type I : NBR( code: N), type II: EPDM(code: E)
Ball valve --- PTFE( code: P)
9.Control mode: for more details, please refer to control circuit diagram
C600 Series Stainless Steel 2/2 Way Mini Electric Ball Valve
(Open/Close Type)
C610 Series WCB 2/2 Way Mini Electric Butterfly Valve
(Open/Close & Wafer Type)
1
2
M
R
WH
Pr
Motor
Open
Close
Control Diagram AC/DC [Transistor Output]
AC Conventional Type, DC Special Type
C.C600 series Electric Valve Control Circuit Diagram
D.Technical Data
Applicable Medium
Non-freezing liquid, gas
Medium Temp
Pressure
Rotary Degree
90°Open/Close Time
Supply Voltage
Motor Configuration
Ambient Temp
Rated Current
Output Torque
Motor Power
1. 6 M Pa
0
90
Empty load：AC/7S,DC/9S（ Loaded ；AC/1 1 S, D C/ 1 3 S）
AC24V，AC85～260V[includingAC110、AC220V] DC24V±5% ,DC12V±5%
Protection Grade：I P6 5 Insulation Resistance：100 MΩ
-3 0～6 0℃
AC 2 4 V/0. 1 5 A，A C85～26 0 V / 0.2A D C 2 4 V/0. 1 5 A ,DC1 2 V / 0.25 A
AC / 7 N·m DC/9N·m
5W
Power
C61 0 Butterfly Valve---Ⅰ[ N BR ] :- 9～8 0℃
C60 0 Ball Valve- --Ⅲ ：-2 9～1 50℃
Ⅱ[EP D M] : -9～12 0℃
1
2
3
4
5
6
M
R
WH
Y
B2
Motor
Position limit1
Position limit 2
Inside the Actuator
Open
Com
Contact Output
Control Circuit Diagram DC [Contact Output]
DC Normal Type
Open
Close
Power
B1
Close
+
-+
-
△
！
Signal output, only voltage ＜50V is allowed to load!
△
！
Signal output, only voltage ＜AV/DC 125V is allowed to load!
Note:NPN transistor output，which can not connect with PLC directly, proper relay should be used.
3
4
5
6
7
G
Y
B2
Electric
Protection
Position limit1
Position limit2
Inside the Actuator
Com
NPN
transistor
emitter
current
output
Earth
open
Close
B1
Special Configuration
C600-T：Cast Brass Body
(1)Red,White,Purple are control wires, Red&White wires connect with power supply, when
purple & Red are short connected, the valve moves towards closed direction, when the
valve closes completely, motor stops working, the valve holds closed position. Vice versa,
purple&white are short connected, valve moves towards open direction, when valve opens
fully, motor stops working, valve holds fully open position.
(2)Valve position signal output is passive signal, NPN transistor emitter current, share the
same collector ( end capacitor: DC50V,20mA). Under such circumstance, the output dial
runs to open position red indicator lights, runs to closed position, green indicator lights.
When it's DC power supply, NPN transistor signal output is unconventional products,
when ordering, please clarify and add letters JT after the model No.
(1)Red & White are control wires, after Red & White wires connect positive and negative poles
of power supply, valve moves towards open direction, when valve opens fully, motor stops,
valve holds open position. Vice versa, switch positive and negative poles, valve moves
towards closed direction, when valve closes completely, motor stops, valve holds fully
closed position.
(2) Valve position signal output is passive signal contact output. The control mode is DC
power supply, normal control mode( Default DC power supply )
