Bestway 65115E User manual

303021211253
1
303021211253_21.0x28.5cm(#65115E) _20季溪流独木舟说明书
Operating, servicing and maintaining a recreational
marine vessel can expose you to chemicals including
engine exhaust, carbon monoxide, phthalates, and
lead, which are known to the State of California to
cause cancer and birth defects or other reproductive
harm. To minimize exposure, avoid breathing
exhaust, service your vessel in a well-ventilated area
and wear gloves or wash your hands frequently when
servicing this vessel. For more information go to
www.P65warnings.ca.gov/marine.
WARNING
OWNER’S MANUAL
MODEL #65115E
The boats are designed and manufactured in conformity with ABYC H-29.
Boat Design Category -“SHELTERED WATERS”: Designed for voyages on sheltered
coastal waters, small bays, small lakes, rivers and canals when conditions up to, and
including, wind force 4 and significant wave heights up to, and including, 0.3 m may
be experienced, with occasional waves of 0.5 m maximum height, for example from
passing vessels.
Warning
IMPORTANT SAFETY INSTRUCTIONS
Follow all the Safety and Operating Instructions. If you don’t follow these instructions,
it may cause the boat to overturn or explode and result in drowning.
1. Do not exceed the maximum recommended number of persons. Regardless of the
number of persons on board, the total weight of persons and equipment must
never exceed the maximum recommended load. Always use the seats/seating
spaces provided.
2. When loading the craft, never exceed the maximum recommended load: Always
load the craft carefully and distribute loads appropriately to maintain design trim
(approximately level). Avoid placing heavy weights high up.
NOTE: The maximum recommended load includes the weight of all persons
onboard, all provisions and personal effects, any equipment not included in the
light craft mass, cargo (if any) and all consumable liquids (water, fuel, etc.).
3. When using the boat, life saving devices such as life jackets and buoys should be
pre-inspected and used at all times.
4. Before every use, carefully inspect all boat components including air-chambers,
grab ropes, oars, and air valves, to ensure everything is in good condition and
WARNING: To avoid damage to the boat and injury to passengers, please don’t
exceed the data given on the builder’s plate.
Technical Specifications
Fig. 1
tightly secured. If you find any damage, please stop to repair it.
5. Buckets, water scoops and air pumps should always be available in case of air
leakage or if the boat takes on water.
6. When the boat is in motion, all passengers must remain seated at all times to
avoid falling overboard. Keep the boat balanced. Uneven distribution of persons or
load in the boat may cause the boat to overturn and result in drowning.
7. Use the craft in sheltered water, up to 300 m (984 feet). Be careful with natural
factors such as wind, tide waters and tidal waves. BE AWARE OF OFFSHORE
WINDS AND CURRENTS. Always wear a lifejacket!
8. If one chamber is punctured when the boat is in the water, it may be necessary to
fully inflate the other air chamber to prevent the boat from sinking.
9. Be careful when landing on the shore. Sharp and rough objects such as rocks,
cement, shells, glass, etc. may puncture the boat. To avoid damage, do not drag
the boat on rough surfaces.
10. The boat is intended for beach use, short-time and short-distance cruising.
11. Be aware of the potential harmful effects of liquids such as battery acid, oil or
petrol. The liquids may damage your boat.
12. Inflate according to the numbered air chamber and rated pressure of the boat, or it
will cause over-inflation and potential and boat explosion. Exceeding the data
given on the capacity plate may cause the craft to be damaged, overturn and lead
to drowning.
13. If you use the tow rings to tow the boat, go slowly to avoid over-towing as damage
may occur.
14. Know how to operate a boat. Check in your local area for information and/or
training as needed. Inform yourself about local regulations and dangers related to
boating and/or other water activities.
15. The operator of a vessel is responsible for the maintenance and safe conduct of
the vessel and the safety of passengers.
16. Prohibit the product misuse, such as, but not limited to: (a) riding seat back,
gunwale, or other unsafe position, (b) failure to use handhold, (c) overloading or
improper loading, (d) excessive speed for the operating conditions, (e) using a
boat in weather or sea conditions beyond the skill or experience of the operator, (f)
continued operation with operator’s visibility blocked or impaired (g) operating
under the influence of drugs or alcohol, and/or (h) modifications.
17. Boat operation where the boat operator or occupants are not under the influence
of drugs and/or alcohol.
18. Knowledge of federal, state, and/or local regulations concerning operation
requirement, including: (a) discharge of oil, (b) solid waste disposal (Marpol
Treaty), (c) marine sanitation, (d) speed, (e) noise, and (f) wake
19. Knowledge of accident reporting requirements.
20. The owner of operator of a vessel is required by law to render assistance to any
individual or vessel in distress, as long as his vessel is not endangered in the
process.
21. U.S.Coast Guard Infoline: [phone]. Web site: www.uscgboating.org
SAVE THESE INSTRUCTIONS
Assembling of the boat
NEVER USE HIGH PRESSURE AIR TO INFLATE INFLATABLES. THIS CAN
DAMAGE YOUR PRODUCT AND VOID YOUR WARRANTY
1. Spread out the boat on level ground.
2. Assemble the removable fin to the bottom of the boat (Fig.1). Make sure the
curvature of the fin is pointed towards the back end of the boat.
NOTE: Assemble the fin before inflation and also disassemble it after deflation.
NOTE: To avoid damage to the removable fin, do not enter shallow water.
Oar
Boat
Components:
• Repair Patch
• Deflation Pipe
Oar blade x 2
Shaft x 1
Coupling x 2
Rope x 2
Storage Cord x 2
Inflation Scale
Removable Fin x 1
Oar ring x 2
Hand Pump
0.03 bar
0.5 psi
9 ft. x 32 in.
(2.75 m x 81 cm)
Item
65115E 1 adult
220 Ibs. (100 kg)
Dry Weight
20.2 lbs. (9.15 kg)
Inflated Size Recommended
Working Pressure
Maximum Load
Capacity
Maximum Number
of Persons

5. Fold the boat from front to back to remove additional air. You can also use a pump
to drain any remaining air.
Repair
1. If there is a small puncture, repair it according to the instruction on repair patch.
2. If the hole is too big to be repaired with the provided patch, purchase a Bestway
repair kit or send the boat to a speciality shop to make the repair.
Registration
If you need to register your boat, please have the boat Hull Identification Number and
model name ready and then visit bestwaycorp.com/support to obtain your Certificate
of Origin, or you can send e-mail to [email protected] for the Certificate of
Origin.
The HIN is located on the starboard outboard side of the hull and near the stern.
PLEASE KEEP THIS MANUAL IN A SECURE PLACE, AND HAND IT OVER TO
THE NEW OWNER WHEN YOU SELL THE CRAFT.
NOTE: All drawings for illustration purpose only. May not reflect actual product.
Storage
1. Keep all accessories for future use.
2. Carefully clean the boat using a mild soap with clean water.
Note: Do not use acetone, acid, and/or alkaline solutions.
3. Use a cloth to gently dry all surfaces.
Note: Do not dry the product in direct sunlight. Also, never dry with equipment such
as electric blowers. Doing so will cause damage and shorten the boat’s life span.
4. Deflate the hull chambers. Deflate all the hull chambers at the same time so the
air-pressure drops together. This will prevent damage from occurring to the boat
inner structures. Next deflate the floor and seat.
2
• Inflate the air chambers with a HAND air pump.
An inflation scale is provided with the product.
Inflate the product until the printed scale is charged up to the same level as that of
the supplied scale. (refer the belowing Table and Illustration)
Caution: Under and over-inflation of the boat will result in safety hazards. It is better
to check the pressure of the boat each time before using. If you use other pressure
gauge, the boat pressure should not be more than the data given on the builder’s
plate.
• Never stand on or rest objects on the boat during inflation.
• Inflate bottom chamber and other accessories such as seat until it is stiff to the
touch but NOT hard.
Item
65115E 10 cm 11.5 cm
Product Inflated Size Deflated Size Inflated Size
Chamber 1
11.8 cm
Inflated Size
Chamber 2
9 ft. x 32 in.
(2.75 m x 81 cm)
For support please visit us at:
bestwaycorp.com/support
©2019 Bestway Inflatables & Material Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle Rechte vorbehalten/Tutti i diritti riservati
®™ Trademarks used in some countries under license to/Marques ®™ utilisées dans certains pays sous la licence de/
Marcas comerciales ®™ utilizadas en algunos países bajo la licencia de/ ®™ Die Warenzeichen werden in einigen Ländern verwendet unter Lizenz der/
®™ Marchi utilizzati in alcuni paesi concessi in licenza a
Bestway Inflatables & Material Corp., No.3065 Cao An Road, Shanghai, 201812, China.
Manufactured,distributed and represented in the European Union by/Fabriqués, distribués et représentés dans l’Union Européenne par/
Fabricado, distribuido y representado en la Unión Europea por/Hergestellt, vertrieben und in der Europäischen Union vertreten von/
Prodotto, distribuito e rappresentato nell'Unione Europea da
Bestway (Europe) S.r.l., Via Resistenza, 5, 20098 San Giuliano Milanese (Milano), Italy
Distributed in North America by/Distribués en Amérique du Nord par/Distribuido en Norteamérica por
Bestway (USA) Inc., 3411 E. Harbour Drive, Phoenix, Arizona 85034, United States of America
Tel: [phone] (For U.S. and Canada)
Distributed in Latin America by/Distribué en Amérique latine par/Distribuido en Latinoamérica por/Distribuído na América Latina por
Bestway Central & South America Ltda, Salar Ascotan 1282, Parque Enea, Pudahuel, Santiago, Chile
Distributed in Australia & New Zealand by Bestway Australia Pty Ltd, 98-104 Carnarvon Street, Silverwater, NSW 2128, Australia
Tel: Australia: ([phone]; New Zealand: 0800 142 101
Exported by/Exporté par/Exportado por/Exportiert von/Esportato da
Bestway (Hong Kong) International Ltd./Bestway Enterprise Company Limited
Suite 713, 7/Floor, East Wing, Tsim Sha Tsui Centre, 66 Mody Road, Kowloon, Hong Kong
www.bestwaycorp.com
Made in China/Fabriqué en Chine/Fabricado en China/Hergestellt in China/Prodotto in Cina
Oars Installation
303021211253_21.0x28.5cm(#65115E) _20季溪流独木舟说明书
1
112
mc