Bestway Helsinki SaluSpa 7 User manual

User Manual of Product 1:
Bestway Helsinki SaluSpa 7 Person Inflatable Outdoor Hot Tub
Spa with 180 Soothing AirJets, Filter Cartridges, Pump, and
Insulated Cover, Brown Wood

Owner’s Manual
Para la instrucción en español,
visite bestwaycorp.com/support
bestwaycorp.com/support
Visit Bestway YouTube channel
FOR INSTRUCTION VIDEOS
PLEASE VISIT
WE SUGGEST NOT TO RETURN
THE PRODUCT TO THE STORE
QUESTIONS? PROBLEMS?
MISSING PARTS?
For FAQ, Manuals, Videos Or
Spare Parts, Please Visit
bestwaycorp.com/support
V
i
s
i
t
w
w
w
.
b
e
s
t
w
a
y
c
o
r
p
.
c
o
m
/
s
u
p
p
o
r
t
f
o
r
h
e
l
p

WARNING
IMPORTANT SAFETY INSTRUCTIONS
When using this electrical equipment, basic safety precautions should always be
followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS.
WARNING – To reduce the risk of injury, do not permit children to use this product
unless they are closely supervised at all times.
A wire connector is provided on this unit to connect a minimum 8 AWG (8.37 mm2)
solid copper conductor between this unit and any metal equipment, metal enclosures
of electrical equipment, metal water pipe, or conduit within 5 feet (1.5 m) of the unit.
DANGER – Risk of injury.
a) Replace damaged cord immediately.
b) Do not bury cord.
c) Connect to a grounded, grounding type receptacle only.
WARNING – This product is provided with a ground-fault circuit-interrupter integrated
with the power plug at the end of the cord. The GFCI must be tested before each
use. With the product operating, push the test button on the GFCI and the product
should not operate. Push the reset button on the GFCI and the product should now
operate normally. When the product fails to operate in this manner, there is a ground
current flowing indicating the possibility of an electrical shock. Disconnect the power
until the fault has been identified and corrected.
DANGER – Risk of Accidental Drowning. Extreme caution must be exercised to
prevent unauthorized access by children. To avoid accidents, ensure that children
cannot use this spa unless they are supervised at all times.
DANGER – Risk of Injury. The suction fittings in this spa are sized to match the
specific water flow created by the pump. Should the need arise to replace the suction
fittings or the pump, be sure that the flow rates are compatible. Never operate spa if
the suction fittings are broken or missing. Never replace a suction fitting with one
rated less than the flow rate marked on the original suction fitting.
DANGER –
Risk of Electric Shock. Install at least 5 feet (1.5 m) from all metal surfaces.
As an alternative, a spa may be installed within 5 feet of metal surfaces if each metal
surface is permanently connected by a minimum 8 AWG (8.37 mm2) solid copper
conductor to the wire connector on the terminal box that is provided for this purpose.
DANGER – Risk of Electric Shock. Do not permit any electric appliance, such as a
light, telephone, radio, or television, within 5 feet (1.5 m) of a spa.
WARNING – To reduce the risk of injury:
a) The water in a spa should never exceed 104°F (40°C). Water temperatures
between 100°F (38°C) and 104°F (40°C) are considered safe for a healthy adult.
Lower water temperatures are recommended for young children and when spa
use exceeds 10 minutes.
b) Since excessive water temperatures have a high potential for causing fetal
damage during the early months of pregnancy, pregnant or possibly pregnant
women should limit spa water temperatures to100°F (38°C).
c) Before entering a spa, the user should measure the water temperature with an
accurate thermometer since the tolerance of water temperature-regulating devices
varies.
d) The use of alcohol, drugs, or medication before or during spa use may lead to
unconsciousness with the possibility of drowning.
e) Obese persons and persons with a history of heart disease, low or high blood
pressure, circulatory system problems, or diabetes should consult a physician
before using a spa.
f ) Persons using medication should consult a physician before using a spa since
some medication may induce drowsiness while other medication may affect heart
rate, blood pressure, and circulation.
WARNING: TO AVOID ELECTRIC SHOCK, DO NOT USE THE SPA WHEN IT IS
RAINING.
WARNING: Water attracts children; Always attach a spa cover after each use.
WARNING: TO REDUCE THE RISK OF INJURY: Never add water that is higher than
104°F (40°C) into the Spa.
CONSULT YOUR PHYSICIAN FOR RECOMMENDATIONS.
CAUTION: The spa should not be setup or left out in temperatures lower than
40°F (4°C).
CAUTION: Do not use the spa alone.
CAUTION: Always enter and exit the spa slowly and cautiously. Wet surfaces are
slippery.
CAUTION: To avoid damage to the pump, the spa must never be operated unless
the spa is filled with water.
CAUTION:
Immediately leave spa if the user feels uncomfortable or sleepy.
NOTE: Please examine equipment before use. Notify Bestway®at the customer
service address listed on this manual for any damaged or missing parts at the time of
purchase. Verify that the equipment components represent the model that you had
intended to purchase.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
CONTENTS
1. Warning .................................. P8
P5
P7
P2
2. Installation .............................
Selected Location
GFCI Test
Assembly
3. Pump Operation .....................
Control Panel
Alarms
4. Maintenance ........................
Filter Cartridge Maintenance
Water Maintenance
Air-Valve Adjustment
Draining the Spa
Cleaning the Spa
Deflation
Spa Repair
P10
5. Troubleshooting ................
2
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
SAVE THESE INSTRUCTIONS

WARNING
IMPORTANT SAFETY INSTRUCTIONS
When using this electrical equipment, basic safety precautions should always be
followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS.
WARNING – To reduce the risk of injury, do not permit children to use this product
unless they are closely supervised at all times.
A wire connector is provided on this unit to connect a minimum 8 AWG (8.37 mm2)
solid copper conductor between this unit and any metal equipment, metal enclosures
of electrical equipment, metal water pipe, or conduit within 5 feet (1.5 m) of the unit.
DANGER – Risk of injury.
a) Replace damaged cord immediately.
b) Do not bury cord.
c) Connect to a grounded, grounding type receptacle only.
WARNING – This product is provided with a ground-fault circuit-interrupter integrated
with the power plug at the end of the cord. The GFCI must be tested before each
use. With the product operating, push the test button on the GFCI and the product
should not operate. Push the reset button on the GFCI and the product should now
operate normally. When the product fails to operate in this manner, there is a ground
current flowing indicating the possibility of an electrical shock. Disconnect the power
until the fault has been identified and corrected.
DANGER – Risk of Accidental Drowning. Extreme caution must be exercised to
prevent unauthorized access by children. To avoid accidents, ensure that children
cannot use this spa unless they are supervised at all times.
DANGER – Risk of Injury. The suction fittings in this spa are sized to match the
specific water flow created by the pump. Should the need arise to replace the suction
fittings or the pump, be sure that the flow rates are compatible. Never operate spa if
the suction fittings are broken or missing. Never replace a suction fitting with one
rated less than the flow rate marked on the original suction fitting.
DANGER –
Risk of Electric Shock. Install at least 5 feet (1.5 m) from all metal surfaces.
As an alternative, a spa may be installed within 5 feet of metal surfaces if each metal
surface is permanently connected by a minimum 8 AWG (8.37 mm2) solid copper
conductor to the wire connector on the terminal box that is provided for this purpose.
DANGER – Risk of Electric Shock. Do not permit any electric appliance, such as a
light, telephone, radio, or television, within 5 feet (1.5 m) of a spa.
WARNING – To reduce the risk of injury:
a) The water in a spa should never exceed 104°F (40°C). Water temperatures
3
between 100°F (38°C) and 104°F (40°C) are considered safe for a healthy adult.
Lower water temperatures are recommended for young children and when spa
use exceeds 10 minutes.
b) Since excessive water temperatures have a high potential for causing fetal
damage during the early months of pregnancy, pregnant or possibly pregnant
women should limit spa water temperatures to100°F (38°C).
c) Before entering a spa, the user should measure the water temperature with an
accurate thermometer since the tolerance of water temperature-regulating devices
varies.
d) The use of alcohol, drugs, or medication before or during spa use may lead to
unconsciousness with the possibility of drowning.
e) Obese persons and persons with a history of heart disease, low or high blood
pressure, circulatory system problems, or diabetes should consult a physician
before using a spa.
f ) Persons using medication should consult a physician before using a spa since
some medication may induce drowsiness while other medication may affect heart
rate, blood pressure, and circulation.
WARNING: TO AVOID ELECTRIC SHOCK, DO NOT USE THE SPA WHEN IT IS
RAINING.
WARNING: Water attracts children; Always attach a spa cover after each use.
WARNING: TO REDUCE THE RISK OF INJURY: Never add water that is higher than
104°F (40°C) into the Spa.
CONSULT YOUR PHYSICIAN FOR RECOMMENDATIONS.
CAUTION: The spa should not be setup or left out in temperatures lower than
40°F (4°C).
CAUTION: Do not use the spa alone.
CAUTION: Always enter and exit the spa slowly and cautiously. Wet surfaces are
slippery.
CAUTION: To avoid damage to the pump, the spa must never be operated unless
the spa is filled with water.
CAUTION:
Immediately leave spa if the user feels uncomfortable or sleepy.
NOTE: Please examine equipment before use. Notify Bestway®at the customer
service address listed on this manual for any damaged or missing parts at the time of
purchase. Verify that the equipment components represent the model that you had
intended to purchase.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
SAVE THESE INSTRUCTIONS

WARNING
IMPORTANT SAFETY INSTRUCTIONS
When using this electrical equipment, basic safety precautions should always be
followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS.
WARNING – To reduce the risk of injury, do not permit children to use this product
unless they are closely supervised at all times.
A wire connector is provided on this unit to connect a minimum 8 AWG (8.37 mm2)
solid copper conductor between this unit and any metal equipment, metal enclosures
of electrical equipment, metal water pipe, or conduit within 5 feet (1.5 m) of the unit.
DANGER – Risk of injury.
a) Replace damaged cord immediately.
b) Do not bury cord.
c) Connect to a grounded, grounding type receptacle only.
WARNING – This product is provided with a ground-fault circuit-interrupter integrated
with the power plug at the end of the cord. The GFCI must be tested before each
use. With the product operating, push the test button on the GFCI and the product
should not operate. Push the reset button on the GFCI and the product should now
operate normally. When the product fails to operate in this manner, there is a ground
current flowing indicating the possibility of an electrical shock. Disconnect the power
until the fault has been identified and corrected.
DANGER – Risk of Accidental Drowning. Extreme caution must be exercised to
prevent unauthorized access by children. To avoid accidents, ensure that children
cannot use this spa unless they are supervised at all times.
DANGER – Risk of Injury. The suction fittings in this spa are sized to match the
specific water flow created by the pump. Should the need arise to replace the suction
fittings or the pump, be sure that the flow rates are compatible. Never operate spa if
the suction fittings are broken or missing. Never replace a suction fitting with one
rated less than the flow rate marked on the original suction fitting.
DANGER –
Risk of Electric Shock. Install at least 5 feet (1.5 m) from all metal surfaces.
As an alternative, a spa may be installed within 5 feet of metal surfaces if each metal
surface is permanently connected by a minimum 8 AWG (8.37 mm2) solid copper
conductor to the wire connector on the terminal box that is provided for this purpose.
DANGER – Risk of Electric Shock. Do not permit any electric appliance, such as a
light, telephone, radio, or television, within 5 feet (1.5 m) of a spa.
WARNING – To reduce the risk of injury:
a) The water in a spa should never exceed 104°F (40°C). Water temperatures
between 100°F (38°C) and 104°F (40°C) are considered safe for a healthy adult.
Lower water temperatures are recommended for young children and when spa
use exceeds 10 minutes.
b) Since excessive water temperatures have a high potential for causing fetal
damage during the early months of pregnancy, pregnant or possibly pregnant
women should limit spa water temperatures to100°F (38°C).
c) Before entering a spa, the user should measure the water temperature with an
accurate thermometer since the tolerance of water temperature-regulating devices
varies.
d) The use of alcohol, drugs, or medication before or during spa use may lead to
unconsciousness with the possibility of drowning.
e) Obese persons and persons with a history of heart disease, low or high blood
pressure, circulatory system problems, or diabetes should consult a physician
before using a spa.
f ) Persons using medication should consult a physician before using a spa since
some medication may induce drowsiness while other medication may affect heart
rate, blood pressure, and circulation.
WARNING: TO AVOID ELECTRIC SHOCK, DO NOT USE THE SPA WHEN IT IS
RAINING.
WARNING: Water attracts children; Always attach a spa cover after each use.
WARNING: TO REDUCE THE RISK OF INJURY: Never add water that is higher than
104°F (40°C) into the Spa.
CONSULT YOUR PHYSICIAN FOR RECOMMENDATIONS.
CAUTION: The spa should not be setup or left out in temperatures lower than
40°F (4°C).
CAUTION: Do not use the spa alone.
CAUTION: Always enter and exit the spa slowly and cautiously. Wet surfaces are
slippery.
CAUTION: To avoid damage to the pump, the spa must never be operated unless
the spa is filled with water.
CAUTION:
Immediately leave spa if the user feels uncomfortable or sleepy.
NOTE: Please examine equipment before use. Notify Bestway®at the customer
service address listed on this manual for any damaged or missing parts at the time of
purchase. Verify that the equipment components represent the model that you had
intended to purchase.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
ASSEMBLY: THE PROVIDED WARNING LABEL
WARNING
REDUCE THE RISK OF ELECTROCUTION
1. NEVER PLACE AN ELECTRIC APPLIANCE WITHIN 5 FEET OF SPA.
REDUCE THE RISK OF CHILD DROWNING
1. SUPERVISE CHILDREN AT ALL TIMES.
2. ATTACH SPA COVER AFTER EACH USE.
REDUCE THE RISK OF OVERHEATING
1. CHECK WITH A DOCTOR BEFORE USE IF PREGNANT, DIABETIC, IN POOR
HEALTH, OR UNDER MEDICAL CARE.
2. EXIT IMMEDIATELY IF UNCOMFORTABLE, DIZZY, OR SLEEPY. SPA HEAT
CAN CAUSE HYPERTHERMIA AND UNCONSCIOUSNESS.
3. SPA HEAT IN CONJUNCTION WITH ALCOHOL, DRUGS, OR MEDICATION
CAN CAUSE UNCONSCIOUSNESS.
WHEN PREGNANT, SOAKING IN HOT WATER FOR LONG PERIODS CAN
HARM YOUR FETUS. MEASURE WATER TEMPERATURE BEFORE ENTERING.
1. DO NOT ENTER SPA IF WATER IS HOTTER THAN 100
O
F (38
O
C)
2. DO NOT STAY IN SPA FOR LONGER THAN 10 MINUTES.
4
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
SAVE THESE INSTRUCTIONS

5
Be sure to cover the spa with the spa cover whenever the heating function is
activated. Leaving the spa uncovered will inrease the heating duration required.
Please do not use the spa when ambient temperature is lower than 39°F.
IMPORTANT !
To reach 104°F (40°C), the heating duration required is base on the starting water temperature and
ambient temperature, the data below is purely for reference. To display the current water
temperature, run the filter system for at least a minute.
NOTE: The warning label must be posted near your spa in a readable position
during using your spa.
1. Take out the warning label from the accessory kit.
2. Carefully peel the warning label.
3. Affix the warning label.
To order the warning label, please contact your local Bestway After Sales Service.
1. Indoor Installation:
Be aware of special requirements if you install the spa indoors.
• Humidity is a natural side effect with SaluSpa installation. Determine the effects of moisture on exposed wood, paper, etc. in the
proposed location. To minimize these effects, it is best to provide plenty of ventilation to the selected area. An architect can help
determine if more ventilation is needed.
2. Outdoor Installation:
• During filling, draining or when in use, water may spill out of the spa. Therefore the SaluSpa should be installed near a floor drain.
• Do not leave the spa's surface exposed to direct sunlight for long periods of time.
INSTALLATION
Selected Location
IMPORTANT: Because of the combined weight of the SaluSpa, water, and users, it is
extremely important that the base where the SaluSpa is installed is smooth, flat, level and
capable of uniformly supporting the weight for the entire time the SaluSpa is installed (not
on the carpet or other similar material). If the SaluSpa is placed on a surface, which does
not meet these requirements, any damage caused by improper support is not covered
under the manufacturer’s warranty. It is the responsibility of the SaluSpa owner to assure
the integrity of the site at all times.
Ambient Temperature
50°F
59°F
68°F
77°F
86°F
Water Temperature
50°F
59°F
68°F
77°F
86°F
Set Temperature
104°F
104°F
104°F
104°F
104°F
Heating Duration
32 h
26 h
20 h
14 h
9 h
Power Rate Massage Tube Power Heat Element Power Water Pump Power
11.3A at 20ºC 0.7A
110-120V AC,
12A at 20ºC 6.5A

GFCI Test
IMPORTANT: RISK OF ELECTRIC SHOCK. THE GFCI MUST
BE TESTED BEFORE TURNING ON THE PUMP EACH TIME.
1. Plug the GFCI into a power outlet, the indicator turns red.
2. Press the test button, the indicator turns off.
3. Press the reset button, the indicator turns red and the spa is ready for use.
WARNING: The GFCI plug must be tested before each use to avoid risk of electric shock.
WARNING: Before inserting plug into a power outlet, make sure the current rate of
the power outlet is suitable for the pump.
WARNING: Do not use the pump if this test fails and contact our Customer Service.
-
l
o
i
n
5
NOTE: When inflating, you will notice that air will be expelled from the area
where the air hose connects to the pump, this is normal for technique
requirements.
NOTE: Do not use an air compressor to inflate the pool.
NOTE: Do not drag the pool on rough ground
as this may cause damage to the pool liner.
NOTE: Inflation time for reference only.
Air Valve Check (for spa with quick inflation/deflation valve)
Always check the air valve carefully before inflation to ensure there is not an
air leak. If the air valve is loose, use the provided wrench to fasten the air
valve following these steps:
With one hand, hold the backside of the air valve from the inner side of the
spa wall and turn the wrench clockwise.
NOTE:
1. Do not over tighten.
2. Do not adjust the air valve connector when the spa is in use.
6

Hyperthermia occurs when the internal temperature of the
body reaches a level several degrees above the normal body
temperature of 37°C (98.6°F). The symptoms of hyperthermia
include an increase in the internal temperature of the body,
dizziness, lethargy, drowsiness, and fainting. The effects of
hyperthermia include failure to perceive heat; failure to
recognize the need to exit spa or hot tub; unawareness of
impending hazard; fetal damage in pregnant women; physical inability to exit the spa
or hot tub; and unconsciousness resulting in the danger of drowning.
WARNING – The use of alcohol, drugs, or medication can greatly increase the risk of fatal
hyperthermia.
7
The pump has a 5-minute auto-lock. The LED light will dim out when the pump is
locked (no function is activated). To lock or unlock the pump, place a finger over
the lock/unlock button for 3 seconds.
Pressing the Temperature Increase or Decrease buttons will cause the LED to flash.
When it is flashing you can adjust to the desired temperature setting. If you hold these
buttons down the values will rapidly increase or decrease. The new and desired
temperature setting will remain on the LED display for 3 seconds to confirm the new value.
Once powered-up the LED displays the current water temperature automatically.
After 72 hours of filtration (without using the power saving timer function),
the pump will hibernate and flash “End” with the current water temperature.
When the pump is hibernating both the heating and water filter functions are
disabled. To re-activate the pump press lock/unlock button for 3 seconds.
Use this button to activate the heating system. When the light above the heat
button is red, the heating system is activated. When the light is green, the water
is at the set temperature and the heating system is at rest.
The temperature can be displayed in either Fahrenheit or Celsius.
NOTE: If the heating system is activated the filtration system will automatically start.
NOTE: After turning off the heating system the filtration system will continue to operate.
NOTE: The default temperature is 35°C (95°F).
NOTE: Temperature adjustment ranges from 20°C (68°F) to 40°C (104°F).
Temperature Adjustment Buttons
Lock/Unlock Button
Celsius/Fahrenheit Toggle
Power-Saving Timer Button
Heat Button
This button turns the filter pump on and off. The light above the Water Filter
Button displays red when activated.
Water Filter Button
Use this button to activate the massage system, which has a 30-minute
auto-shutoff feature. The light above the Massage System Button displays red
when activated.
IMPORTANT: Do not run the Massage system when the cover is
attached. Air can accumulate inside the spa and cause irreparable
damage and bodily harm.
NOTE: Heat and massage system work together to create a warm
massage experience.
Massage System Button
Power-Saving Timer LED
LED Display
NOTE: The water heat rate may change in the conditions below:
• When the outdoor temperature is below 15°C (59°F).
• If the cover is not in position when the heating function is activated.
NOTE: To display the current water temperature, run the filter system for at least a
minute. The water temperature as tested by an external thermometer may vary from the
temperature as displayed on the spa panel by as much as approximately 2°C.
This is a newly added function, designed to help avoid wasting power by setting
the time and duration of the heating cycle for the spa.
This way, you can enjoy your spa at the time you desire, without needing to
leave the heater on at all times.
STEP 1: Set the heating duration
1. Press the button unit the LED starts to flash.
2. Press the or button to adjust the heating duration (From 1-48 hours).
3. Press the button again to confirm the heating duration.
STEP 2: Set the number of hours FROM NOW when the heater will activate
1. After setting the heating duration, the LED starts to flash.
2. Press the or button to adjust the hours until time of activation
(From 0-99 hours).
3. Press button again or simply touch nothing for 10 seconds to confirm
the setting. The LED will light steadily, and the countdown to heater activation will
begin.
To modify the timer settings: Press the button and use the or button to adjust.
Cancel the setting: Press the button for 2 seconds.
NOTE: After setting, the screen flashes the current temperature and time alternately.
NOTE: Timer adjustment (amount of time with the heater ON) may be set from 1 to 48
hours; Reservation time adjustment (the number of hours FROM NOW when the
heater will begin to function) may be set from 0 to 99 hours. If the timer is set at 0 hour, the
heating system will activate immediately.
Note that the timer is one time per use - the user sets the duration of the heating cycle, and
how many hours from now the heating cycle begins. The timer does NOT repeat until reset.
Press this button for 2 seconds to active the control panel bottons and the light turns to
green. Press this button for 2 seconds to turn off all currently activated functions.
On/Off Button
This LED flashing means you are setting the heating duration. The light will be on
when the heating function starts to work.
This LED flashing means you are setting the number of hours FROM NOW when the
heater will activate. When the light is on, the Power-Saving Timer function is set.
Assembly part refer to the provided
installation leaflet.

1. The water flow sensor flags didn’t fall
back into the correct position.
2. The water flow sensors are broken.
1. You forgot to remove the 3 stopper caps from
inside the pool.
2. Filter cartridges are dirty.
3. Activate the filter or heat system and put your
hand in front of the outlet pipe inside the pool
to check if you can feel water flowing out.
a. If no water flows out the water pump is broken.
b. Water flows out but the alarm appears,
than the water flow sensors are broken.
1. The water temperature is lower than 4°C (40°F).
2. If the water temperature is higher than
7°C (44.6°F), the pump’s thermometer is
broken.
1. The water temperature is over 48°C (119°F).
2. If the water temperature is lower than 45°C
(113°F), the pump’s thermometer is broken.
1. The pump’s thermometer connectors don’t
work properly.
2. The pump’s thermometer is broken.
1. The ambient temperature is over 50°C (122°F)
or the pump is directly under the sunshine.
2. The thermal cut-out is broken.
1. Unplug the pump, strike the side of the pump firmly (but not violently), and
plug it back in.
2. To get assistance visit our website www.bestwaycorp.com support section.
1. Remove the two stopper caps before starting the heating system. Refer to
the Assembly section in the User’s Manual.
2. Remove the filter set from inside the pool and push the filter or heat button.
If no alarm appears, clean or change the filter cartridges and re-install the
filter set inside the pool.
3. To get assistance visit our website www.bestwaycorp.com support section.
1. The spa is not designed to operate with water temperatures lower than 4ºC
(40°F). Unplug the pump and only re-start the pump when the water
temperature reaches 6°C (43°F).
2. To get assistance visit our website www.bestwaycorp.com support section.
1. The spa is not designed to operate with water temperatures greater than
40°C (104°F). Unplug the pump and only re-start the pump when the water
temperature reaches 38°C (100°F) or lower.
2. To get assistance visit our website www.bestwaycorp.com support section.
To get assistance visit our website www.bestwaycorp.com support section.
1. Unplug the pump, and put the pump in a dry, cool place. Only re-start the
pump when the water temperature reaches 34°C (93.2°F) or lower.
2. To get assistance visit our website www.bestwaycorp.com support section.
Solutions
Causes Reasons
The water flow sensors work
without pressing the filter or
heat button.
After starting or during the
functions of filtering or/and
heating, the water flow
sensors do not detect water
flow.
The pump’s thermometer
reads the water temperature
below 4°C (40°F).
The pump’s thermometer
reads the water temperature
over 48°C (119°F).
The pump’s thermometer
connections have issues.
The thermal cut-out cut
off.
Alarms
P04674
Filter Set
58323
Filter Cartridge
CAUTION: YOU MUST ENSURE THE PUMP IS UNPLUGGED
BEFORE BEGINNING SPA MAINTENANCE TO AVOID RISK
OF INJURY OR DEATH.
Filter Cartridge Maintenance
NOTE: To ensure your spa water stays clean, check and clean your filter cartridges
every day follow the steps below.
NOTE: We recommend changing your filter cartridges every week or, if the filter
cartridges remain soiled and discolored, they should be replaced.
Water Maintenance
Keeping your spa water clean and chemically balanced is necessary. Simply cleaning
the filter cartridge is not enough for proper maintenance, we recommend you use
pool chemicals to maintain water chemistry and chlorine or bromine tablets (do not
use granules) with the chemical dispenser.
NOTE: We recommend you take a shower before using your SaluSpa, as cosmetic
products, lotions, and other residues on the skin can quickly degrade water quality.
To use the chemical dispenser, please follow the below instruction.
Maintenance
NOTE: Your spa will require additional air to be added from time to time. Changes in
temperature from day to night will change the pressure in the spa and may cause a
certain amount of deflation. Please follow the Assembly instructions and drain the
spa before inflating to the accurate pressure needed.
8
Using chemical tablets (not included):

NOTE: Damage resulting from chemical imbalance is not covered by the warranty. Pool
chemicals are potentially toxic and should be handled with care. There are serious health risks
from chemical vapors and the incorrect labeling and storage of chemical containers. Please
consult your local pool supply retailer for more information about chemical maintenance. Pay
close attention to the chemical manufacturer's instructions. Spa damage resulting from misuse
of chemicals and mismanagement of spa water is not covered by the warranty.
NOTE: Remove the chemical dispenser from spa when the spa is in use.
IMPORTANT: After performing chemical maintenance and before using the spa, use
a test kit (not included) to test the water chemistry. We recommend maintaining your
water as below table.
pH
7.4-7.6
Total Alkalinity
80-120ppm
Free Chlorine
2-4ppm
Using chemical liquid (not included):
STORAGE
Draining the Spa
Air-Valve Adjustment (For quick inflation/deflation valve Only)
In case of air leakage, check the air-valve first. Using soapy water, cover the air-valve to check if air is leaking, if so, use the
provided wrench to fasten the air-valve following these steps:
• With one hand, hold the backside of the air-valve from the inner side of the spa wall and turn the wrench clockwise.
NOTE:
1. Do not over tighten.
2.
Always check the air-valve carefully before use.
3. Do not adjust the air-valve connector when the spa is in use.
Detergent residues and dissolved solids from bathing suits and chemicals may build
up on the spa walls. Use soap and water to clean the walls and rinse thoroughly.
NOTE: DO NOT use hard brushes or abrasive cleaners.
Cleaning the spa
2. 3. 4.
6.
1.
7.
5.
8. NOTE: Dry the spa pool.
NOTE: Lift up the spa when there is
only a little water left. Damages to
the handles are not covered under
the warranty.
P00217
9

DEFLATION
REPAIR
For PVC part.
If the spa is torn or punctured, use the provided underwater adhesive
repair patch.
1. Clean area to be repaired.
2. Carefully peel patch.
3. Press patch over area to be repaired.
4. Wait 30 seconds before inflation.
For Tritech PVC material.
If the spa is torn or punctured, use the provided PVC repair patch and glue
(not included) following these steps:
1. Clean and dry area to be repaired.
2. Cut the provided PVC patch to appropriate size.
3. Use glue (not included) to coat the one side of the newly cut patch. Make
sure the glue is evenly distributed.
4. Wait for 30 seconds and then place the cut patch with glue over the
damaged area.
5. Smooth out any bubbles of air that may be trapped underneath, and press
firmly for two minutes.
6. The product is once again ready for use. Repeat this process should
further leaks occur.
7. Wait 30 minutes before inflation.
P61725ASS18
-
l
o
i
n
5
s
e
c
.
Quick inflation/deflation valve Safety valve
2
2.
P61727ASS18
-
l
o
i
n
5
s
e
c
.
Screw valve
1.
P61726ASS18
P61726ASS18
P61725ASS18
P61727ASS18
10

11
Problems
Pump does not operate
Pump does not heat properly
Massage System
does not work
Pump adapters are not level with
the spa adapters
Spa pool leakage
Water is not clean
Probable Causes
- Spa is torn or punctured
- Air valve is loose
Solutions
- Check power source
- To get assistance visit our website www.bestwaycorp.com support
section
- Elevate the pump with wood or another type of insulated material to
bring the pump's adapters level with the spa's adapters
- Power failure
- GFCI broken
- Temperature set too low
- Dirty Filter Cartridge
- The thermal cut-out cut off
- Spa is not covered
- Heating element failed or fuse
cutout
- Air Pump is overheating
- The massage system
stops automatically
- Air pump is broken
- One characteristic of PVC is that it
changes shape, which is normal
- Insufficient filtering time
- Dirty Filter Cartridge
- Improper water maintenance
- Set to a higher temperature refer to section pump operation
- Clean/replace the filter cartridge refer to section filter cartridge
cleaning and replacement
- Unplug the pump, and put the plug in a dry, cool place. Only restart
the pump when the water temperature reaches 35°C (95°F) or lower
- Attach the cover.
- To get assistance visit our website www.bestwaycorp.com support
section
- Unplug the pump and wait two hours until the pump has cooled.
Insert the plug and press the massage system button
- Press the massage system button to reactivate
- To get assistance visit our website www.bestwaycorp.com support
section
- Increase filtration time
- Clean/replace the Filter Cartridge (refer to Filter Cartridge Cleaning
and Replacement section)
- Refer to the chemical manufacturer’s instructions
There is a defect in your SPA To get assistance visit our website www.bestwaycorp.com support
section
- Use provided repair patch
- Using soapy water, cover the air-valve to check if air is leaking, if
so, use the provided wrench to fasten the air-valve following these
steps:
1. Deflate the SPA.
2. With one hand, hold the backside of the air valve from the inner
side of the spa wall and turn the wrench clockwise.
Control panel not working
What kind of chemicals should be
used for water maintenance? Please consult your local chemical supplier for information about chemical maintenance.
Pay close attention to the chemical manufacturer’s instructions.
Water leaks from the adapters
between the pump and spa
Insert the three stopper caps on to the spa’s ports to prevent water from escaping and disconnect the
pump. Check and make sure the seals are placed correctly inside the pump adapters. If the seals are
missing or not installed correctly, to get assistance visit our website www.bestwaycorp.com support
section. If the seals are correctly in place, reconnect the pump to the SPA and hand-tighten the adapters.
The control panel has an auto-lock,
which is activated after 5 minutes of
inactivity. The LED display has one
icon: If the lock icon is
highlighted, the control panel is
locked.
- Control panel is not activated.
- To unlock the control panel, press the button for 3 seconds.
If the control panel will not unlock, restart the pump – unplug and
plug in the pump.
- Press the on/off button for 2 seconds. If the problem persists, to
get assistance visit our website www.bestwaycorp.com support
section.
GFCI test failed
TROUBLESHOOTING
Bestway strives to provide the most trouble-free Spas on the market. If you
experience any problems whatsoever, do not hesitate to contact Bestway or your
authorized dealer. Here are some helpful tips to help you to diagnose and rectify
some common sources of trouble.
NOTE: Plastic becomes brittle and susceptible to breaking
when exposed to subzero temperatures. Freezing can
severely damage the spa. Improper winterization of your
spa can void your warranty.
Make sure the spa and pump are completely dry. This is essential to extend the life of the spa. It
is recommended you store the spa in its original package in a warm dry place.

303021241336
For support please visit us at:
bestwaycorp.com/support
©2020 Bestway Inflatables & Material Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle Rechte vorbehalten/Tutti i diritti riservati
®™ Trademarks used in some countries under license to/
Marques ®™ utilisées dans certains pays sous la licence de/
Marcas comerciales ®™ utilizadas en algunos países bajo la licencia de/
®™ Die Warenzeichen werden in einigen Ländern verwendet unter Lizenz der/
®™ Marchi utilizzati in alcuni paesi concessi in licenza a
Bestway Inflatables & Material Corp., No.3065 Cao An Road, Shanghai, 201812, China.
Manufactured,distributed and represented in the European Union by/
Fabriqués, distribués et représentés dans l’Union Européenne par/Fabricado, distribuido y representado en la Unión Europea por/
Hergestellt, vertrieben und in der Europäischen Union vertreten von/Prodotto, distribuito e rappresentato nell'Unione Europea da
Bestway (Europe) S.r.l., Via Resistenza, 5, 20098 San Giuliano Milanese (Milano), Italy
Distributed in North America by/Distribués en Amérique du Nord par/Distribuido en Norteamérica por
Bestway (USA) Inc., 3411 E. Harbour Drive, Phoenix, Arizona 85034, United States of America
Tel: [phone] (For U.S. and Canada)
Distributed in Latin America by/Distribué en Amérique latine par/Distribuido en Latinoamérica por/Distribuído na América Latina por
Bestway Central & South America Ltda, Salar Ascotan 1282, Parque Enea, Pudahuel, Santiago, Chile
Distributed in Australia & New Zealand by Bestway Australia Pty Ltd, Unit 2/98-104 Carnarvon St Silverwater, NSW 2128, Australia
Tel: Australia: ([phone]; New Zealand: 0800 142 101
Exported by/Exporté par/Exportado por/Exportiert von/Esportato da
Bestway (Hong Kong) International Ltd./Bestway Enterprise Company Limited
Suite 713, 7/Floor, East Wing, Tsim Sha Tsui Centre, 66 Mody Road, Kowloon, Hong Kong
www.bestwaycorp.com