Better Homes and Gardens KENDARA BH18-021-199-24 User manual

PB 1
model# BH18-021-199-24
Lot#_________Date________
Customer Service:
1.877.436.7290
[email protected]
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
rich espresso
Manufactured By:
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Assembly Instructions
KENDARA DESK

2
TOP PANEL
LEFT SIDE ASSEMBLY
RIGHT SIDE ASSEMBLY
RAIL
BACK PANEL
DRAWER FRONT
A
B
C
D
E
F
DRAWER LEFT SIDE
DRAWER RIGHT SIDE
DRAWER BACK
DRAWER BOTTOM
DRAWER SUPPORT
G
H
I
J
K
Before you begin:
1. Check for damaged or missing parts.
2. Use the carton as a working surface to prevent product damage during assembly.
TOOLS NEEDED
PARTS LIST
Hammer Flat Head Screwdriver Phillips Head Screwdriver

2 3
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
3. Cam
x9
4. Cam Cover
x2
1. Wood Dowel
x12
2. Cam Bolt
x9
5. Bolt
x4
6. Lock Washer
x4

4
12. Wall Anchor
x1
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
9. Handle Bolt
x4
10. Handle
x2
7. Washer
x6
8. Short Flat Head
Screw
x5
11. Allen Wrench
x1

54
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
14. Truss Head Screw
x1
13. Long Flat Head
Screw
x3
15. Wall Strap
x1

6
1 2
3 4 5
180º
HOW TO USE THE CAM LOCK SYSTEM

6 7
x2 x2
STEP 1
1. Screw-In cam bolts must be screwed down ush.
2. Refer to page 6 for instructions on how to use the cam lock system.
2. Cam Bolt 3. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

8
x6 x4
x4
x4
x4
x2
x1x4
(H13)
STEP 2
1. Wood
Dowel
2. Cam Bolt
5. Bolt
3. Cam 13. Long
Flat Head
Screw
6. Lock
Washer
11. Allen
Wrench
7. Washer
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 6 for instructions on how to use the cam lock system.
4. Do not over tighten screws.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

8 9
x6 x3x3 x2
x5
STEP 3
1. Wood
Dowel
2. Cam Bolt 3. Cam 4. Cam Cover
8. Short Flat
Head Screw
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 6 for instructions on how to use the cam lock system.
4. Do not over tighten screws.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

10
x4 x2
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten screws.
STEP 4
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
9. Handle
Bolt
10. Handle

10 11
x1x1x1x1
x2
12
13
14
7
7
15
STEP 5
14. Truss
Head Screw
13. Long Flat
Head Screw
15. Wall
Strap
7. Washer
12. Wall
Anchor
position against wall
mark position of strap hole on wall
drill 1/4”hole
tap in wall anchor
fasten anti-tip strap with wall
screw provided
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

12
70 lbs. / 31.8 kg.
20 lbs. / 9.1 kg.
WARNING: Do not exceed the maximum load capacity. Exceeding the maximum load capacity may result in
collapse and possible injury.
Furniture Care Instructions:
Dust with clean, lint-free cloth.
Use furniture spray polish as needed.
Customer Service:
877.436.7290
[email protected]
Your complete satisfaction is our number 1 priority. Our product is designed and manufactured to meet the
highest quality of standards. In the event that you have assembly questions, or parts are missing or damaged,
our customer service department would appreciate the opportunity to assist you.
This product carries a one (1) year warranty against defects in workmanship and materials. Defective product
will be replaced free of charge within the stated warranty period, when returned by the original purchaser with
proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. Please
contact our Customer Service at 1-877-436-7290 to obtain information on warranty performance. This warranty
gives you specic legal rights and you may also have other rights which vary from State to State.
!WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Install tip-over restraint provided.
• Place heaviest items in the lowest drawers.
• Do not set TV’s or other heavy objects on top
of this product, unless the product is
specifically designed to accommodate them.
• Never allow children to climb or hang on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
(OR)
• Do not defeat or remove the drawer interlock
system.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is a permanent label. Do not remove.

PB 1
model# BH18-021-199-24
Lot#_________Fecha_______
Servicio al Cliente:
1.877.436.7290
[email protected]
ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA.
café
Fabricado Por :
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
ESCRITORIO KENDARA
Instrucciones de Ensamble

2
PANEL SUPERIOR
ENSAMBLE DEL LADO IZQUIERDO
ENSAMBLE DEL LADO DERECHO
RIEL
PANEL POSTERIOR
CAJÓN FRONTAL
A
B
C
D
E
F
CAJÓN LATERAL IZQUIERDO
CAJÓN LATERAL DERECHO
CAJÓN POSTERIOR
CAJÓN INFERIOR
SOPORTE DE CAJÓN
G
H
I
J
K
Antes de comenzar:
1. Compruebe si hay piezas dañadas o faltantes.
2. Utilice la caja de cartón como supercie de trabajo para evitar daños al producto durante el montaje.
HERRAMIENTAS NECESARIAS
LISTA DE PARTES
Destornillador de Cabeza PlanaMartillo Destornillador Phillips

2 3
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
3. Leva
x9
4. Cubierta del
Tornillo
x2
2. Tornillo de leva
x9
1. Clavija de Madera
x12
5. Perno Largo
x4
6. Arandela Fijadora
x4

4
12. Taquete de Pared
x1
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
9. Perno de Agarradera
x4
10. Agarradera
x2
7. Arandela
x6
8. Tornillo Corto de
Cabeza Plana
x5
11. Llave Allen
x1

54
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
14. Tornillo de Cabeza
Redonda
x1
13. Tornillo Largo de
Cabeza Plana
x3
15. Cincha de Pared
x1

6
1 2
3 4 5
180º
COMO USAR EL SISTEMA FIJADOR DE LEVA

6 7
x2 x2
PASO 1
1. Los tornillos de leva deben de estar atornillados al ras.
2. Reérase a la página 6 para instrucciones para como usar el sistema de levas.
2. Tornillo
de Leva
3. Leva
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.

8
x6 x4
x4
x4
x4
x2
x1x4
(H13)
PASO 2
1. Clavija de
Madera
3. Leva2. Tornillo
de Leva
11. Llave
Allen
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Los tornillos de leva deben de estar atornillados al ras.
3. Reérase a la página 6 para instrucciones para como usar el sistema de levas.
4. No sobreapriete los tornillos.
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.
5. Perno 6. Arandela
Fijador
7. Arandela
13. Tornillo
Largo de
Cabeza Plana