Better Homes and Gardens BH17-021-099-25 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2017-02-24 Rev. 0001-B Factory: FOCIDI
Modern Farmhouse Kitchen Island
Stock # BH17-021-099-25
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions and
parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASE
D
:
/
/

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOGUE: Modern Farmhouse Kitchen Island (BH17-021-099-25)
MADE IN CHINA
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making sure Cam
Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of Cam
Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
You are now ready to assemble the KD unit.
1. Please read the Assembly Instructions prior to assembling the unit.
2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.
3. Keep all hardware part out of reach of children.
4. Please wait until all steps are completed before fully tightening bolts.
5. Make sure all bolts are tightly fastened before the unit is used.
GENERAL INFORMATION, TIPS
AND
TRICKS
MAXIMUM RECOMMENDED WEIGHT LOADS
THIS UNIT IS INTENDED FOR USE ONLY WITH THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM
WEIGHTS INDICATED MAY RESULT IN INSTABILITY
,
CAUSING POSSIBLE INJURY.
MAXIMUM LOAD 200 lb. (90.7 kg)
MAXIMUM LOAD 50 lb. (22.6 kg)

3
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Side Frame (Qty. 2 ) C- Stretcher (Qty. 2)
D- Bottom Shelf (Qty. 1) E- Adjustable Shelf (Qty. 1) F- Side Handle (Qty.2)
G- Locking Caster (Qty. 2) H- Swivel Caster (Qty. 2)
(1) Cam Lock (2) Cam Bolt (3) M8 x 30 mm Wood Dowel
(Qty. 6+1 extra) (Qty. 6+1 extra) (Qty. 12+1 extra)
(4) 1-1/4" Bolt (Qty. 6+1 extra)
(5) 1-3/4" Bolt (Qty. 18+1 extra)
(6) Lock Washer (7) Flat Washer (8) Shelf Pin
(Qty. 24+1 extra) (Qty. 24+1 extra) (Qty. 4+1 extra)
Hex Wrench (Qty. 1) Open Wrench (Qty. 1) Touch-up Pen (Qty. 1)
Tools required: Hex wrench and open wrench (provided) and Phillips screwdriver (not provided)

4
D
B
4
6
7
Assembly Instructions
NOTE: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled, go
back and fully tighten all bolts. This will make the assembly easier.
1. Unpack the unit and confirm that you have all the hardware and required parts. Assembly the unit on a
carpeted floor or empty carton to avoid any scratch.
2. Position one Side Frame (B) upside down with the threaded inserts facing up.
3. Attach the Bottom Shelf (D) to the Side Frame (B) with three 1-1/4" Bolts (4) and three Washers (6 and
7).
1-1/4” Bolt
(3 used in this step)
④
Lock Washer
(3 used in this step)
⑥
Flat Washer
(3 used in this step)
⑦

5
Assembly Instructions
4. Repeat the same procedure to attach the other Side Frame (B) at the opposite end.
1-1/4” Bolt
(3 used in this step)
④
Lock Washer
(3 used in this step)
⑥
Flat Washer
(3 used in this step)
⑦
B
B
D
4
6
7

6
B
B
D
C
C
5
6
7
3
3
Assembly Instructions
5. Flip the assembled unit upside down.
6. Insert four Wood Dowels (3) into the outer holes on one Stretcher (C) and attach it to the Side Frames
(B) with four 1-3/4" Bolts (5) and four Washers (6 and 7).
7. Repeat the same procedure to attach the other Stretcher (C) at the opposite end.
Lock Washer
(8 used in this step)
⑥
Flat Washer
(8 used in this step)
⑦
M8 x 30 mm Wood Dowel
(8 used in this step)
③
1-3/4” Bolt
(8 used in this step)
⑤

7
B
B
D
C
C
5
6
7
567
F
F
Assembly Instructions
8. Attach the Side Handles (F) to the Side Frames (B) with four 1-3/4" Bolts (5) and four Washers (6 and
7).
Lock Washer
(4 used in this step)
⑥
Flat Washer
(4 used in this step)
⑦
1-3/4” Bolt
(4 used in this step)
⑤

8
Assembly Instructions
9. Lay out the Top Panel (A) with the holes facing up. Securely screw the Cam Bolts (2) into the
designated small holes.
A
2
Cam Bolt
(6 used in this step)
②

9
3
3
3
3
A
C
C
B
B
D
1
1
Assembly Instructions
10. Insert four Wood Dowels (3) into the non-threaded holes on the Top Panel (A).
11. Position the previous assembly onto the inserted Wood Dowels (3) and attach to the Top Panel (A) by
engaging six Cam Locks (1) (Refer to page 3 on Cam Lock system operation supplement).
M8 x 30 mm Wood Dowel
(4 used in this step)
③
Cam Lock
(6 used in this step)
①

10
5
6
7
5
6
7
A
B
B
D
Assembly Instructions
12. Secure the Side Frames (B) to the Top Panel (A) with six 1-3/4" Bolts (5) and six Washers (6 and 7).
Lock Washer
(6 used in this step)
⑥
Flat Washer
(6 used in this step)
⑦
1-3/4” Bolt
(6 used in this step)
⑤

11
D
B
B
A
G
G
H
H
Assembly Instructions
13. Securely screw the Casters (G and H) to the bottom of the Side Frames (B) with the enclosed open
wrench.

12
Assembly Instructions
14. Ask for assistance to stand the assembled unit upright.
15. Insert four Shelf Pins (8) into the desired holes in the Side Frames (B). Make sure you place the four
Shelf Pins in the same level so the shelf is not tilted. Depend on the desired configuration, tilt and rest
the Adjustable Shelf (E) onto the Shelf Pins (8) making sure the end notches of the Adjustable Shelf fit
onto the Shelf Pins properly.
NOTE: The Adjustable Shelf (E) is designed to be reversed as a Wine Rack.
Shelf Pin
(4 used in this step)
⑧
8
8
BB
E
E

13
Care and Maintenance
Use a soft, clean cloth that will not scratch the surface when dusting.
Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
Using solvents of any kind on your furniture may damage your furniture’s finish.
Never use water to clean your furniture as it may cause damage to the finish.
Always use coasters under beverage glasses and flowerpots.
Liquid spills should be removed immediately. Using a soft, clean cloth, blot the spill gently. Avoid rubbing.
Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create
spotting within the furniture finish.
In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a
professional to repair your furniture.
Check bolts/screws periodically and tighten them if necessary.
Further Advice about Wood Furniture Care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from
direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful
tips will enhance your furniture as it ages.
A touch-up pen has been provided to repair any small nicks or scratches that may occur during
assembly or shipping.
We hope you enjoy your purchase for many years.
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or
replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet
your highest expectations. We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from State to State.
Customer Service: 866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenstyle.com

ESTE INSTRUCTIVO CONTIENE INFORMACION IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y MANTENGA PARA USO FUTURO.
Fecha 2017-02-24 Rev. 0001-B Fábrica: FOCIDI
Isla para Cocina Granja Moderna
Seri # BH17-021-099-25
ENSAMBLE REQUERIDO POR ADULTO
Si tienen alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne esté producto
a la tienda donde lo compró. Por favor llame a nuestro departamento de ayuda al cliente teniendo su
instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica:
866-942-5362
Hora Estándar del Pacífico: 8:30 am - 4:30 pm, de Lunes - Viernes
O visite nuestro sitio web las 24 horas del día, 7 días a la semana para recibir asistencia del producto
en www.whalenstyle.com
O por correo electrónico su petición a [e-mail]
NÚMERO de LOTE:
FECHA de COMP
RA
:
/
/

2
FABRICANTE: Whalen Furniture Manufacturing
CATALOGO: Isla para Cocina Granja Moderna (BH17-021-099-25)
HECHO EN CHINA
SISTEMA DE OPERACIÓN DE TUERCA DE FIJACIÓN
CÓMO FUNCIONA LA INSTALACIÓN DE MONTAJE (KD)
1. Fijar los tornillos de fijación en los orificios pequeños. Conectar ambos paneles, cerciorandose que los
tornillos de fijación entren bien y que estos queden en los orificios al final del panel con tuercas de fijación.
2. Inserte las tuercas de fijación en los orificios grandes del panel. Hacer que la flecha en la tuerca este
apuntando hacia la entrada del tornillo de fijación.
3. Una vez que el tornillo este conectado dentro, tome un destornillador de cruz y apriete la tuerca en
dirección de las manecillas del reloj.
Está listo para el ensamble KD de esta unidad.
1. Por favor lea el instructivo antes de comenzar el ensamble.
2. Para evitar daños, ensamblar el producto en una superficie fuerte, nivelada y libre de abrazivos.
3. Mantenga todo el material de ferretería fuera del alcance de niños.
4. Esperar hasta que todos los pasos esten completados antes de apretar los tornillos.
5. Asegurar de que los tornillos y tuercas esten apretados antes de usar la unidad.
INFORMACIÓN GENERAL, RECOMENDACIONES Y TRUCOS
MÁXIMAS CARGAS RECOMENDADAS
CARGA MÁXIMA 200 lb. (90.7 kg)
CARGA MÁXIMA 50 lb. (22.6 kg)
ESTA UNIDAD DEBE UTILIZARSE CON LOS PESOS MÁXIMOS
INDICADOS. SI SE EXCEDE EL PESO MÁXIMO, PODRÍA RESULTAR EN UNA
INESTABILIDAD DE LA UNIDAD CAUSANDO POSIBLES LESIONES.

3
Lista de partes y material de ferretería
Por favor lea completamente las instrucciones y verifique que estén todas las partes antes de
iniciar el ensamblado.
A- Panel superior (Cant. 1) B- Marco lateral (Cant. 2 ) C- Soporte (Cant. 2)
D- Repisa inferior (Cant. 1) E- Repisa ajustable (Cant. 1) F- Manija lateral (Cant.2)
G- Rueda con freno (Cant. 2) H- Rueda giratoria (Cant. 2)
(1) Tuerca de fijación (2) Tornillo de fijación (3) Perno de madera de M8 x 30 mm
(Cant. 6+1 extra) (Cant. 6+1 extra) (Cant. 12+1 extra)
(4) Tornillo de 1-1/4" (Cant. 6+1 extra)
(5) Tornillo de 1-3/4” (Cant. 18+1 extra)
(6) Arandela de presión (7) Arandela plana (8) Perno de repisa
(Cant. 24+1 extra) (Cant. 24+1 extra) (Cant. 4+1 extra)
Llave hexagonal (Cant. 1) Llave española (Cant. 1) Plumón de retoque (Cant. 1)
Herramientas requeridas: Llave hexagonal y llave española (proveidas) y desarmador estrella (no proveido)

4
D
B
4
6
7
Instructivo de ensamble
NOTA: Por favor no apriete completamente todos los tornillos, hasta que termine con el ensamble de
las partes, después asegurese de apretar todos los tornillos, ésto hará el ensamble más fácil.
1. Desempacar la unidad y confirmar que se tiene todo el material de ferretería y partes requeridas.
Ensamblar la unidad en un piso alfombrado o en el cartón vacío para evitar rasguños.
2. Posicionar un marco lateral (B) boca abajo con los insertos roscados apuntando hacia arriba.
3. Adjuntar la repisa inferior (D) al marco lateral (B) con 3 tornillos de 1-1/4" (4) y 3 arandelas (6 y 7).
Tornillo de 1-1/4”
(3 usados en este paso)
④
Arandela de presión
(3 usados en este paso)
⑥
Arandela plana
(3 usados en este paso)
⑦

5
Instructivo de ensamble
4. Repetir el mismo procedimiento para adjuntar el otro marco lateral (B) en el lado opuesto.
Tornillo de 1-1/4”
(3 usados en este paso)
④
Arandela de presión
(3 usados en este paso)
⑥
Arandela plana
(3 usados en este paso)
⑦
B
B
D
4
6
7

6
B
B
D
C
C
5
6
7
3
3
Instructivo de ensamble
5. Voltear la unidad ensamblada boca abajo.
6. Insertar 4 pernos de madera (3) en los agujeros exteriores de un soporte (C) y adjuntar a los marcos
laterales (B) con 4 tornillos de 1-3/4" (5) y 4 arandelas (6 y 7).
7. Repetir el mismo procedimiento para adjuntar el otro soporte (C) al lado opuesto.
Arandela de presión
(8 usados en este paso)
⑥
Arandela plana
(8 usados en este paso)
⑦
Perno de madera de
M8 x 30 mm
(8 usados en este paso )
③
Tornillo de 1-3/4”
(8 usados en este paso)
⑤

7
B
B
D
C
C
5
6
7
567
F
F
Instructivo de ensamble
8. Adjuntar las manijas laterales (F) a los marcos laterales (B) con 4 tornillos de 1-3/4" (5) y 4 arandelas
(6 y 7).
Arandela de presión
(4 usados en este paso)
⑥
Arandela plana
(4 usados en este paso)
⑦
Tornillo de 1-3/4”
(4 usados en este paso)
⑤