Bezalel Prelude User manual

Portable Wireless Charger
Prelude

Magnetic Cover
Nano-suction
Area
Wireless
Recharging Area
Wireless
Charging Area
USB-C Port
Battery Status
LED Indicator
Wireless
Recharging
LED Indicator
Power
LED Indicator

Welcome to Prelude
Shake the Prelude 1-2 times and LED indicators
will light up. Prelude will be in standby mode for 30
seconds. Prelude is ready to go.
Prelude will automatically turn off if there is no
action for 30 seconds. All LED indicators will turn
off.
If the battery power lower than 5%, LED indicators
will blink. Please charge it fully.

Plug USB-C end of cable into Prelude USB-C port.
Plug USB-A end of cable into power adapter (not
included).
Use QC2.0 or higher USB adapter for improved fast
recharging experience.
Charging Prelude
Before using Prelude for the first time, charge it fully.
TWO WAYS to charge Prelude:
Charging Prelude by Cable

Charging Prelude by Wireless Device
Place wireless recharging area face down (the side
with logo) onto a Qi-charging device (not
included). Wireless recharging LED Indicator will
light up to show Prelude is being recharged
wirelessly.
Use fast wireless charging pad (15W) for improved
fast recharging experience.

Charging Your Device with Prelude
After the Prelude is fully charged, you can use it to
charge your wireless or wired devices.
Remove magnetic cover. Remove film from
nano-suction area.
Wireless Charging
Shake the Prelude 1-2
times and LED
indicators will light
up. Prelude is ready
to go.
1.

Gently press Prelude’s
nano-suction charging area
onto the glossy-surface of your
phone.
* For nano-suction
attachment, the back of your
phone or phone case must
have a glossy surface.
* Use BEZALEL Magnetic Case
to automatically align and for
better holding a proper charge.
2.
Wireless charging, on the go.
3.

Wired Charging
Shake the Prelude 1-2
times and LED
indicators will light
up. Prelude is ready
to go.
1.
Connect the Prelude to your phone with a USB-C
cable (not included).
2.

Plug USB-A end of
cable into power
adapter.
* Make sure to use a
2.0A output power
adapter (not included).
1.
Shake the Prelude 1-2
times and LED indicators
will light up.
2.
Using Prelude as a Conventional
Wireless Charging Base
When using a cable, you can use Prelude like a
conventional wireless charging base: set your
phone down and it starts charging.

Conventional wireless charging.
Note: once your phone gets to 100%, the
Prelude will start recharging.
4.
Gently press Prelude’s
nano-suction charging area
onto the glossy-surface back
of your phone.
* For nano-suction
attachment, the back of your
phone or phone case must
have a glossy surface.
* Use BEZALEL Magnetic Case
to automatically align and for
better holding a proper charge.
3.

Store Prelude
Once you finish using the Prelude, you can place the
Magnetic Cover above the Nano-suction Area for
anti-stick dust.
Cleaning Guide
If your NanoGrip sticky mat becomes dirty or dusty,
it will lose some of its stickiness.
Gently rub the nano-suction area with your finger
with lukewarm water and air dry. This will make it
regain stickiness and can be used over and over
again. Do not put Prelude under running water.
Safety & Handling
1. Keep wireless charging unit dry and away from
liquids. Do not use on wet surfaces.
2. Do not attempt to disassemble or modify charger.
3. Always disconnect power supply before cleaning
charger.
4. Keep away from high heat. Use in the temperature
range between 0 and 45 degrees Celsius (32 and 113
degrees Fahrenheit).
5. Phone case cannot have any ring attachment,
credit card, metal or magnetic sticker. This may
cause overheating and affect the wireless charging
process.

Battery Capacity
Wireless Input
USB-C Input
Wireless Output
USB-C Output
5000 mAh
12V / 1A
DC 5V, 9V, 12V ; 18W
DC 5V / 1A, 9V / 1.2A, 12V / 0.9A
5V / 2A, 9V / 1.67A, 12V / 1.5A
Specifications
Prelude Portable Wireless Charger X1
USB-C Cable X1
User Manual X1
Package Contents