BEZGAR BZR 6 User manual

1
1) Please read and understand the manual before using, assembling, and/or disassembling.
2) This product is not a toy, it is a high powered RC model, which is not intended for operators
under14 years of age.
3) Children less than 14 years old must not operate this product unless they are closely
supervised by an adult.
4) Fully charge the battery pack before use. Be sure to disconnect and remove the batteries
from both the transmitter and the car when not in use.
5) Do not attempt to run the product while low on battery power. Fully charge the battery pack
before use. Stop driving immediately when slow running speed is observed. Failure to do such
can over drain the pack and cause damage.
!
Caution
General Safety Information:
1.This manual is subject to change without prior notification.
2.This product is NOT a toy, and not intended for users under 14 years of age, unless closely
supervised by an adult.
3.The specifications and images in the manual may vary from the actual product.
4.Operate this vehicle with due care and be always a good driver which is attentive to others.
5.Under no circumstances SHOULD the user operate the vehicle in crowds of people.
Serious injury could result.
6.Never operate the vehicle on public streets or in public areas. This could cause traffic
accidents, personal injury, and/or property damage. This vehicle is ONLY be driven on the
open track which is for RC cars.
7.Do NOT use this vehicle to chase pets or other animals.
8.The receiver, steering servo and other electronics installed in this vehicle are merely splash
water-resistant. Do not immerse this vehicle into water.
9.Regularly checking on the transmitter (radio controller) power is very important. Remove the
batteries from the transmitter (radio controller) when not in use. Replace with fresh batteries
if necessary. NEVER run this vehicle with low power from the transmitter.
10. When this vehicle becomes stuck, do NOT force on throttle. Failure to do so could cause
abrupt damage to the motor and/or the ESC (Electronic Speed Controller). Check and clean
the obstacles before running again.
11. Before running this vehicle check if the battery, wiring, and plugs are loose.
12. Be careful not to touch any moving parts when servicing or operating this vehicle.
13. To prevent excessive RPM from damaging the motor, and/or the drive-train components,
we suggest reducing the throttle while performing in the air during jumps.
14. Never attempt to re-assemble motor, ESC, and receiver as these have been precisely
calibrated at factory.
15. Always apply the factory optional/tooling parts to this vehicle.
16. To upgrade this vehicle requires the user to upgrade the entire radio/driving system
(such as motor, ESC, receiver and so forth.) They should be strictly matched with factory
components.
17. To run this vehicle, turn on the transmitter (radio controller) first and then the receiver.
18. To stop running this vehicle, turn off the receiver first, and then the transmitter.
19. Straighten the receiver antenna (if it comes with this vehicle) for best receiving
performance. Never cut the receiver antenna, otherwise it could lose control of the vehicle.

Practice Required:
2
2.4GHz Transmitter Introduction:
Beginners should start slowly. Keep practicing until you feel comfortable with steering, throttle,
and brakes. Once you feel comfortable driving the vehicle try a different terrain and speed until
you have mastered the basics.
Once you have learned the basics,
try different patterns and tracks to
improve your skills.
Add a friend for a race or try to beat
your best times!
Slide and remove the battery cover from the
transmitter, install two AA size batteries
(1.5V,each), and replace the battery cover.
Do not reverse the polarities when installing.
Always use batteries of same brand and
remove batteries when not in use. Make sure
battery power is sufficient before use.
Please replace the batteries for the transmitter if the transmitter LED blinks slowly.
Always erect the antenna for best performance.
Always straighten the antenna for the best performance.
1) Steering Wheel
2) Trigger
3) Steering Trim
4) Speed Selection
5) Steering Direction Reverse
Switch
6) Power Indicator
7) Power ON/OFF
8) AUX. Button
(This button is disabled
for this car)
1
2
4
7
6
8
3
5
Power Switch
1
2 3 4
Power Switch:
Press and hold for 2-3
seconds to switch on or off.
1) Power Indicator
2) Servo Slot (5-pin)
(for 5-wire Servo)
3) Aux. Slot (for LED light
if it contains LED)
4) Motor Plug Slot

3
Starting Driving:
4) Throttle Control:
A) With the steering wheel centered, the vehicle runs in a straight line.
Slight adjustment by flipping the steering wheel is occasionally needed. It largely depends
on the terrains that you drive.
B) Turn the steering wheel to the left, and the car turns left.
C) Turn the steering wheel to the right, and the car turns right.
Pull the trigger to accelerate , release it to slow the speed,
and push to brake. Pull it to the Center Position and push it
again to go reverse.
PULL IT
BACK
PUSH IT
FORWARD
FORWARD
STOP
REVERSE
3) Checking the steering performance by turning the steering wheel:
CENTER
CENTER
Press and hold to switch on
1) Switch on the Transmitter:
Slide the Power Switch to “ON” position. Make sure the transmitter
has enough battery power. Please replace with the new batteries for
transmitter if the LED on transmitter blinks slowly. Do NOT move the
trigger and the steering wheel while the transmitter is waiting for
binding.
2) Switch on the ESC/Receiver:
Press and hold the Power Switch on ESC/Receiver for 2-3 seconds to
turn on the car. It will take a few seconds before LEDs (on Transmitter
and the ESC/Receiver) stop blinking and become solid
on, which indicates that the car is bound with the
transmitter. Binding operation may fail with low battery
power. Please stop and charge the battery pack once
the car jerks, cogs, or moves slowly. Under the
circumstance of flat battery power, the car may have
steering but not throttle. In case the car runs harshly or
noisily, stop to check if there is something clogged in
the drive train.

5) Steering Trim Knob:
It is used to set the steering neutral point on front wheels. If the front wheels on the vehicle
veer in one direction while the steering wheel is centered, turn this knob in the opposite
direction until the vehicle drives straight.
Stopping Driving:
4
1) Switch off the ESC/Receiver:
Press and hold the Power Switch for
2-3 seconds until LED on ESC/Receiver
goes off.
2) Switch off the Transmitter:
Slide Power Switch to “OFF” position
3) Disconnect and remove the battery
pack from the car when not in use.
Fully charge the battery pack before
storing it.
4) Make sure there are no damage parts before
storing it.
6) Speed Switch Knob:
7) Steering Direction Reverse Switch:
If the vehicle turns right when you steer
left, flip “Steering Reverse” switch.
If the vehicle turns left when you steer
right, flip “Steering Reverse” switch.
STEERING TRIM
SPEED SWITCH
STEERING
REVERSE
The Speed Switch is actually the throttle limiter. Turning down the knob all the way will reduce
the maximum speed down to 40% of maximum speed. Turning up the knob will increase max
speed up to 100%. It is advisable to operate the vehicle on the slower setting until you have
had enough practice before operating at higher speeds.
Press and hold to switch off

5
Charging The Battery Pack:
Use ONLY the specified charger (provided in the box) to charge the battery pack.
Note: The balance USB charger is provided in the box.
During charging, the red LED is on solid, which monitors the charging process.
The red LED will go off after the battery pack has been fully charged.
Charging Duration: Li-ion Battery Pack 7.4V, 800 mAh (Approx. 2-2.5 hours),
Soft Pack Li-Po Battery Pack 7.4V,1000mAh (Approx. 2.5 hours)
Tip: Smart phone AC POWER adaptors (5V,2A ) can be applied to cut down charging period.
The red LED flashes, which indicates:
1) USB charging cable is connected with the battery pack but not being plugged on the charging slot.
2) Non-rechargeable battery pack is connected
3) Not able to charge as the battery pack is over-discharged.
4) USB cable is in an unstable connection.
!
WARNING!
-Do not charge the battery pack unattended.
-Do not use damaged and/or leaky batteries or a damaged charger.
-Children are not allowed to charge the battery without being closely supervised
by adults.
Precautions:
-Be sure to always disconnect the battery pack and
remove it from the vehicle when not in use.
-Please fully charge the battery before each use.
-Do not leave the battery pack uncharged or fully
charged for long periods of time.
-Do not completely drain the battery while running the
vehicle. Do not charge the battery under any
wet or damp conditions. Only charge in dry conditions.

6
Maintenance:
Troubleshooting:
We strongly recommend that you check and maintain the vehicle after use.
Please read and understand the list below which will facilitate you.
A. The vehicle does not work at all:
1) Check to ensure that radio controller and car are switched on.
2) Check if there are damaged parts/wires/connectors, repair or replace if necessary.
3) Car battery is flat. Charge the battery pack.
B. The vehicle runs slowly:
1) Car battery is flat. Charge the battery pack.
2) Check if the vehicle is properly geared and no dirty or stripped gears are found. Make sure
there is a reliable gear mesh for motor pinion and the spur gear.
3) Check if there is something stopping the moving parts and clean them immediately.
C. The throttle works but not the steering:
1) Check if the servo feels jammed, and try centering it gently if it is the case.
2) Check if the servo link is loose or the servo breaks. Repair or replace if needed.
D. It steers, but throttle is uncontrollable:
1) Check if there are damaged parts in the overall drive train.
2) Check the battery power both for radio controller and the car.
E. The vehicle runs noisily:
1) Check gear mesh between spur gear and motor pinion.
2) Check if there are stripped and/or dirty gears.
3) Check if there are some parts getting damaged in the overall drive train.
F. The vehicle is found one direction's steering travel is not same to the other.
Please tune the Steering Trim until Steering Center Point is fixed.
G. Not able to charge the batteries:
Check if either the charger or the batteries is damaged, or batteries are over-discharged.
-Disconnect and remove the batteries from the car and the radio controller when not in use.
-Do not leave the rechargeable battery pack uncharged or fully charged for a long time.
-Check if there is any obvious damage after each use.
-If the vehicle runs noisily check to see if there is any broken or slipped gears and check
if there is a clogged drive train.
-Check if the wheels are well tightened after use.
-Check if there are any loose screws in the chassis.
-Check if there are not frayed, damaged, loosened wires, or connectors.
-Check if the steering servo is in good order. It may wear out over time and require replacement.
-Check if there are any objects getting twisted in the drive train. Replace them if necessary.
-Check the motor and motor wires after use. Never attempt to re-assemble the motor.
-Clean the car body and chassis with a soft lint-free cloth.
-Store the vehicle in a clean, cool, and dry place out of children's reach.

7
Headlight Installation
123
4 5 6
1) The headlight, which is provided as a gift in the box, is not installed on the car.
2) Please take out the headlight, the zip ties, and the adhesive tape from the box.
(See Photo 1)
3) Please plug the headlight plug into the slot on the ESC/Receiver. (See Photo 2).
Note: Do not force while plugging or unplugging.
4) Please apply the adhesive tape to the headlight board and stick it on the upper deck
as shown in Photo 3.
5) Gently insert the headlights into the slots on the back of the front bumper. Make sure they
are in place.(See Photo 4 and Photo 5)
6) Please keep the wires in order and bind them up with the aid of the zip ties. (See Photo 6)

7

8
PART LIST-1
Chassis
Front Gear Box Top
Housing
Rear Bumper Assembly Front Lower Suspension
Arms(Left/Right)
Front Upper Suspension
Arms(Left/Right)
Body Posts Shock Absorbers(2P)
For continuous improvements , the images may vary from your received model.
Rear Gear Box Top
Housing
M16001 M16002 M16003 M16004
Front Bumper Assembly
M16005 M16006 M16007 M16008
Rear Lower Suspension
Arms(Left/Right)
M16009 M16010 M16011 M16012
Rear Upper Links+
Steering links+Servo
Link
M16013 M16014 M16015 M16016
Front/Rear Drive Shafts Diff. Outdrive Cups Steering Hubs
M16017 M16018 M16019 M16020
Servo Top Plate+
Motor Guard
Spur Gear+Drive
Pinions
Steering Bushes+
Ackerman Plate
Shock Towers(Front
and Rear)
Rear Hubs
Diff. Complete
(Front/rear)

9
PART LIST-2
Servo Saver Assembly Centre Drive Shaft
Rear Hub Pins (4P)
Drive Shaft Pivot
Pins (8P) Diff. Assembly
Plastic Pivot Balls
Complete
Electronic Speed
Control/Receiver
For continuous improvements , the images may vary from your received model.
Front Upper Suspension
Hinge Bolts
M16021 M16022 M16023 M16024
Front/Rear Lower
Suspension Hinge Pins
M16025 M16026 M16027 M16028
Steering Posts (4P)
M16029 M16030 M16031 M16032V3
Diff. Posts+Pins
M16033 M16034V2 M16035 M16036
Motor Heatsink
Servo (5-wire)
M16055 M16-B005CH1
Truck Body (Yellow)
Steering Pivot Balls (8P)
Motor 390
Wheels Complete
Motor Pinions(14T)
+Set Screw
M16150
Li-PO Soft Pack 7.4V,
1000mAH,25C
(Dean-Plug) Headlight LED
M16061

10
PART LIST-3
Battery Binding Strap Wheel Hex.
USB charger
Pan head Self Tapping
Screws PBHO2*8mm
Countersunk Self Tapping
Screws KBHO2.3*6mm
Pan head Self Tapping
Screws PBHO2.6*12mm
For continuous improvements , the images may vary from your received model.
Zip Ties (8P)
M16050 M16038 12010 P010
18859E-E001
S007 S029 S058
Countersunk Screws
KM2.5*8
S088
S103 S128 S161
Countersunk Self Tapping
KBHO2.6*12mm
S204
S225 S226 S227
Countersunk Self Tapping
Screws KBHO2.3*12mm
Pan head Self Tapping
Screws PBHO2*12mm
Wheels Complete
12P 12P 12P
12P 12P 12P
12P
12P 12P 12P
12P
Pan head Self Tapping
Screws PBHO2.6*10mm
Pan head Self Tapping
Screws PBHO2.3*4mm
Flange Head Self Tapping
Screws PWTHO2.6*12mm
793127 635953
Ball Bearings
(φ7.93*12.7*3.95mm)
Ball Bearings
(φ6.35*9.53*3.17mm)
8P 8P
M16060
Wheel Lock Blots
8P
16014
Steering Hub Step Screws
8P
Set Screw 2.5x2.5mm

11
PART LIST-4
For continuous improvements , the images may vary from your received model.
M16100A M16101 M16102 M16103
M16104 M16105 M16106 M16107
M16108 M16109 M16110V2 M16111
Brushless Motor
Aluminum Capped Oil
Filled Shocks
Machined Metal Spur
Gear
Machined Metal Diff.
Gears+Diff. Pinions
Machined Metal Diff.
Outdrive Cups+Pins
Metal Front CVD Shafts
+Pins+Lock Nut M4
Wheelie Bar Assembly Brushless ESC/Receiver
OPTIONAL OPTIONAL OPTIONAL OPTIONAL
OPTIONAL OPTIONAL OPTIONAL OPTIONAL
OPTIONAL OPTIONAL OPTIONAL OPTIONAL
Metal Rear Dogbones
Metal Rear Wheel Shafts
+Pins+Lock Nut M4
Heavy Duty Center Drive
Shaft +Outdrive Cups+
Pins+Screws (suited for
metal spur gear version)
H165
Body Clips (6 pairs)
Servo (3-wire plug, for
brushless Version)
M16035T
Motor Pinions(13T)
+Set Screw
OPTIONAL

12
ASSEMBLY VIEW-1
SHOCK ASSEMBLY
DIFF. ASSEMBLY
STEERING ASSEMBLY
M16012
M16031
M16029
M16029 M16027
M16029
793127
M16029
M16027
M16028
M16017 M16017
M16009
M16017
M16021
M16033
M16021
M16021
M16021
M16009
M16027
M16027
M16027
M16027
M16027
M16018
S103
S226
16014
S226
16014
Adjusted Ring: Rotate this ring to adjust spring tension for
desired suspension travel.

CENTER DRIVE ASSEMBLY
FRONT SUSPENSION ASSEMBLY
REAR SUSPENSION ASSEMBLY
ASSEMBLY VIEW-2
M16020
793127
M16020
793127
M16015
M16006
M16007
M16031
M16008
S088
M16025
13
M16022
635953
635953
M16020
M16013
635953
635953
635953
635953
M16014 M16014

14
ASSEMBLY VIEW-3
FRONT/REAR SHOCK TOWER
BODY POST ASSEMBLY
BUMPER ASSEMBLY
M16011
M16010
M16011
M16010
M16011
M16005
M16004
S007
S007 S029
S029
S007
S007
S029
S029
M16004
M16005
S029
S029
M16023
M16023

15
ASSEMBLY VIEW-4
M16018
M16018
M16001
M16019
S029
S029
S029
S226

16
ASSEMBLY VIEW-5
M16034 M16035 M16019
M16003
M16002
S029
S029
S029
S029
S226
M16015
M16024

17
S161
S128
S161
S128 S128
M16024
M16024
S226
S226
S226
S226
S029
M16009
M16009
M16031
M16031
M16009
S226
ASSEMBLY VIEW-6

18
M16060
M16055
12010
H165
H165
H165
H165
ASSEMBLY VIEW-7