BGR Mods INTENSAFIRE 2.0 User manual

Congratulations on purchasing the IntensaFIRE 2.0! We‘re positive you’ll love all the IntensaFIRE 2.0 has
to offer. We’re always open to your comments and suggestions for extra features so if you find anything is
missing, don’t hesitate to get it touch.
Getting to know your controller
At first you may be wondering how on earth the IF2 works when there appears to be no extra buttons,
holes, or anything out of the ordinary from the outside. The genius of the IntensaFIRE 2.0 is that it’s totally
stealth by design meaning only those who know how to use it will know it is there.
The IF2 is turned on and configured primarily with the R1, Start and Left D-Pad buttons, with more
advanced features described later using other buttons too.

! IMPORTANT !
When turning on controller do not press any buttons while the Player 3 indicator is flashing. The chip
initializes when the controller is first turned on and needs all triggers to be released.
Activating
Before the chip is ready to respond to any command, you must tell it to “activate” and become ready to
receive a command. To activate it hold R1 and tap the Start button. As you do this the Player 4 indicator
light will come on.
Selecting Modes
To select a mode, first activate the chip by holding R1 and tapping the Start button so the Player 4 LED
comes on. You must activate the chip each time you want to change modes. With the chip activated and
the Player 4 LED turned on, hold R1 down and keep tapping the Left D-Pad however many times for the
mode you want, and then release R1.
To select Mode 7 you would hold R1, tap Left 7 times, and then release R1. The Player 3 LED will flash with
each press of Left, and then when releasing R1 will flash back the mode number to confirm you are doing
things correct. Slow flashes = 10, fast flashes = 1, so mode 7 is no slow flashes, but 7 fast flashes.
Quick Enable / Disable
If at any point you want to quickly disable the chip, activate the chip (R1+Start) then press Left without any
other buttons pressed. The light will flash rapidly several times then go off. The chip is now disabled. If you
were previously in a mode and want to quickly get everything back on, repeat the steps and it will re-enter
where you left off.
Master Reset
As the IntensaFIRE 2 has many Features that can be turned on and off and rapid fire speeds and other
timings that can be adjusted by the user, sometimes you just want to factory restore the chip to the
beginning in case you forget that it is active and what is altered.
To master reset the chip, activate (R1+Start) then hold down Square+Left for 6 seconds. After 6 seconds the
light will fade in then fade out (pulse). Your chip is now reset.

IntensaFIRE 2.0 Modes
1. Rapid Fire
2. Rapid Fire Alternate Speed
3. Dual Trigger
4. Rapid Fire (3 Burst)
5. Jitter Fire
6. Fast Reload
7. Rapid Fire + Fast Reload
8. Drop Shot
9. Rapid Fire + Drop Shot
10. User Programming Mode
11. Battlefield 3 Auto Tagging Mode
Adjusting Speed
One of the best things about the IntensaFIRE 2.0 is that every single mode uses Rapid Fire and can have its
speed completely customized for future proof games.
By default the speed of the rapid fire is what we call Speed Mode 9. The slowest speed is Speed Mode 50,
and fastest is Speed Mode 1.
To adjust the speed of all modes on the chip, activate the chip (R1+Start) then go into the User
Programming Mode (by entering the “User Programming” mode from the list above as you would enter any
other mode by holding R1 and tapping Left however many times for the mode) and you will notice when
you release R1 the Player 3 LED will stay on after entering the mode instead of flashing back the mode
number to you. You are now ready to adjust the speed. You will start in whatever speed you were currently
in, so if you haven’t done this before it will be Speed Mode 9 by default.
To increase the speed, press and release L1 and the Player 3 LED will flash once to indicate an increase in
speed. You will now go to Speed Mode 8 (if you were in 9 to start with). You can test this speed on the fly by
holding R1. To continue increasing the speed just press L1 again and again until you get to where you want.
If you go too far, or want to slow down the speed hold Xand press L1.
Once you are happy with your speed tap Left and it will flash back to the Speed Mode you are in. This
speed is then hard saved into the chip and will be remembered even when the battery is removed you can
now select any mode that uses Rapid Fire and see the speed has totally changed.
NOTE: If you get a bit lost as to what speed your chip is now in you can reset it to Speed Mode 9 by going
into User Programming Mode and holding Ofor 3 seconds. The Player 3 LED will flash a few times then go
off. The speed is now reset and you can go to any mode you like as before.
Auto Tagging Mode
This mode applies to Battlefield 3 only, activating this mode will allow you to put a tag on an enemy
everytime you begin to shoot your target, giving you points and your teammates the location on the enemy
incase he gets away. First Activate the mod by holding R1 and tapping Start. Once activated hold Select
and tap left on the Directional Pad.