BIC Graphic 32166 User manual

USER MANUAL
32166 Bluetooth Speaker and Earbud adapter
with Clip
1 – LED indicator
2–Vol+
3–Mode
4–Vol–
5–MicroUSBInputPort
6–AUXInputPort
Product Specifications:
Bluetooth version : 4.2
Bluetooth profiles: HSP,HFP,ADP AND
AVRCP
Battery: lithium battery 110 MAH
Music playing time: 4 hours(earphone)/2.5
hours(speaker)
Talk time:3 hours(earphone)/1.5
hours(speaker)
Charging time: 2 hours
Input Voltage: 5V
Input Current: 25mA
(earphone)/50mA(speaker)
Skip and Voice prompt: Support
First Time Use:
(Fully charged before first time use)
.
Connect the provided charging cable to a
power source and to the micro USB port on
the headphones.
.
The LED indicator light shows red when
charging and turns off when fully charged.
ON/OFF
Switch on – Press and hold Mode key until
Blue LED light will be blinking
Switch off – Press and hold Mode key until
Blue LED light disappeared
Wireless Set Up:
Press the Mode button, hold until the Blue
LED light is blinking

Using a Bluetooth enabled device, search
the possible connections for “GC-20”.
After selecting “GC-20” it will connect the
device and the Bluetooth Receiver.
Audio Functions:
Once connected to a Bluetooth enabled
device press the Mode button to play the
selected audio.
Press Mode again to pause the audio.
If receiving a call via the Bluetooth
connection, the audio will immediately
pause, and will continue when the call is
ended.
Long Press “Vol + “ key – To play next song
Long Press “Vol – “ key – To play previous
song
Short Press “Vol + “ key – To volume up
Short Press “Vol – “ key – To volume down
Short Press “Mode” key – To pause/stop
Phone Functions:
Under connected mode when phone call
comes in:
Long press the Mode key to reject
ShortpresstheModekeytoanswer
ShortpresstheModekeytoendthecall
Double press the Mode key to redial the
last number
SAFETY PRECAUTIONS:
WARNING-When using this product, basic
precautions should always be followed,
including the following:
1. Read all the instructions before using
the product.
2. Never store or use this product in
temperatures below 32°F(0°C) or above
115°F(45°C).
3. The unit’s full performance is achieved
onlyafter2or3completedchargeand
discharge cycles.
4. To reduce the risk of injury, close
supervision is necessary when the
product is used near children.
5. Do not expose the device to moisture.
6. Donotusethedeviceinexcessofits
output rating. Overload outputs above
rating may result in a risk of fire or
injury.
7. Do not use the device if damaged or
modified.
8. Damaged or modified batteries may
exhibit unpredictable behavior resulting
in fire, explosion or risk of injury.
9. Do not disassemble the device. Take it
to a qualified service person when
service or repair is required. Incorrect
reassembly may result in a risk of fire or
injury.

10. Do not expose the device to fire or
excessive temperature. Exposure to fire
or temperatures above 104°F may
cause explosion.
11. Have servicing performed by a qualified
repair person using only identical
replacement pairs.
12. This will ensure that the safety of the
product is maintained.
FCC Statement:
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment general uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to try to correct the
interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
This device complies with part 15 of the FCC
rules. Operation is subject to the following
two conditions (1) this device may not
cause harmful interference, and (2)this
device must accept any interference
received, including interference that may
cause undesired operation.