Big Backyard F23073C User manual

INSTALLATION AND OPERATING INSTRUCTIONS
10-14 Hrs
To reduce the risk of serious injury or death, you must read and
follow these instructions. Keep and refer to these instructions often
and give them to any future owner of this play system. Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE - 29’11” x 26’ area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6’5”
CAPACITY - 10 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks.
Two person
assembly
WARNING
17'-11"
26'-0"
29’11"
9'-10"
83.000
3403073C Rev 01/03/2013
Table of Contents
Warnings and Safe Play Instructions. . . . . . . . . . . . . . . pg. 2
Protective Surfacing Guidelines. . . . . . . . . . . . . . . . . . . pg. 3
Instructions for Proper Maintenance . . . . . . . . . . . . . . . pg. 4
About Our Wood – Limited Warranty . . . . . . . . . . . . . . pg. 5
Keys to Assembly Success . . . . . . . . . . . . . . . . . . . . . . pg. 6
Metric Conversion Sheets . . . . . . . . . . . . . . . . . . . . . pg. 7,8
Part ID .......................................pg. 9
Installation of I.D./Warning Plaque . . . . . . . . . . . .Final Step
ASHBERRY II PLAY SYSTEM – F23073C
Solowave Design
375 Sligo Rd. West, PO Box 10
Mount Forest, ON Canada N0G 2L0
General Inquiries:
8:00am - 4:30pm EST
Toll Free: 1-877-966-3738

Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
Observe capacity limitations of your play-set. See
front cover.
Dress children with well fitting and full foot enclosing
footwear.
Teach children to sit with their full weight in the center
of the swing seat to prevent erratic swing motion or
falling off.
Check for splintered, broken or cracked wood; missing,
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
Verify that suspended climbing ropes, rope ladders, chain
or cable are secured at both ends and cannot be looped
back on itself as to create an entanglement hazard.
On sunny and or hot days, check the slide and other
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with water and wipe
dry prior to using.
Do not allow children to wear open toe or heel footwear
like sandals, flip–flops or clogs.
Do not allow children to walk, in front, between, behind
or close to moving rides.
Do not let children twist swing chains or ropes or loop
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature failure.
Do not let children get off rides while they are in motion.
Do not permit climbing on equipment when it is wet.
Do not permit rough play or use of equipment in a
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
Do not allow children to swing empty rides or seats.
Do not allow children to go down slide head first or
run up slide.
2
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set as
recommended on page 3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 6 feet from any
obstruction such as a garage or house, fences, poles,
trees, sidewalks, walls, landscape timbers, rocks,
pavement, planters, garden borders, overhanging
branches, laundry lines, and electrical wires. (See
OBSTACLE FREE SAFETY ZONE on cover)
CHOKING HAZARD
Prior to assembly, this product contains small parts.
DO NOT allow children less than 5 years of age near or
around loose nuts, screws, washers, plastic bags and
other small parts.
WARNING LABEL
Owners shall be responsible for maintaining the legibility
of the warning labels.
STRANGULATION HAZARD
• NEVER allow children to play with ropes, clotheslines,
pet leashes, cables, chains or cord-like items when using
this play-set or to attach these items to play-set.
• NEVER allow children to wear loose tting clothing,
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
• NEVER allow children to wear bike or sport helmets
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play set tipping over and loose-fill
surfacing materials washing away during heavy rains.
DO NOT allow children to play on the play-set until the
assembly is complete and the unit is properly anchored.
WARNING
WARNING – Safe Play Instructions
Warnings and Safe Play Instructions
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
Observe capacity limitations of your play-set. See
front cover.
Dress children with well fitting and full foot enclosing
footwear.
Teach children to sit with their full weight in the center
of the swing seat to prevent erratic swing motion or
falling off.
Check for splintered, broken or cracked wood; missing,
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
Verify that suspended climbing ropes, rope ladders, chain
or cable are secured at both ends and cannot be looped
back on itself as to create an entanglement hazard.
On sunny and or hot days, check the slide and other
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with water and wipe
dry prior to using.
Do not allow children to wear open toe or heel footwear
like sandals, flip–flops or clogs.
Do not allow children to walk, in front, between, behind
or close to moving rides.
Do not let children twist swing chains or ropes or loop
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature failure.
Do not let children get off rides while they are in motion.
Do not permit climbing on equipment when it is wet.
Do not permit rough play or use of equipment in a
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
Do not allow children to swing empty rides or seats.
Do not allow children to go down slide head first or
run up slide.
WARNING
WARNING – Safe Play Instructions
2
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set as
recommended on page 3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 6 feet from any
obstruction such as a garage or house, fences, poles,
trees, sidewalks, walls, landscape timbers, rocks,
pavement, planters, garden borders, overhanging
branches, laundry lines, and electrical wires. (See
OBSTACLE FREE SAFETY ZONE on cover)
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains small parts
and parts with sharp edges and points. Keep parts away
from children until fully assembled.
STRANGULATION HAZARD
• NEVER allow children to play with ropes, clotheslines,
pet leashes, cables, chains or cord-like items when using
this play-set or to attach these items to play-set.
• NEVER allow children to wear loose tting clothing,
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
• NEVER allow children to wear bike or sport helmets
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play set tipping over and loose-fill
surfacing materials washing away during heavy rains.
DO NOT allow children to play on the play-set until the
assembly is complete and the unit is properly anchored.




Keys to Assembly Success
Part Identification Key
On each page, you will find the parts and
quantities required to complete the assembly
step illustrated on that page. Here is a sample.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only
a flat washer is required. For ease of
installation liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer first then flat washer then
hole. Because the assemblies need to
be squared do not completely tighten
until instructed. Pay close attention to
diameter of the bolts. 5/16” is slightly
larger than 1/4”.
Once the assembly is tightened, watch for exposed
threads. If a thread protrudes from the T-Nut, remove the
bolt and add washers to eliminate this condition. Extra
washers have been provided for this purpose.
This identifies information that requires special
attention. Improper assembly could lead to an
unsafe or dangerous condition.
Where this is shown, 2 or 3
people are required to safely
complete the step. To avoid
injury or damage to the
assembly make sure to get help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to assure
proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole before
fastening screw or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill
1/8” Bit
Tighten
Bolts
No Yes
CAUTION – Protrusion Hazard
Tools Required
6
Shovel Level #2 & #3 Phillips
or Robertson
Safety
Glasses
Drill (1/8”
3/16” Bit)
Measuring
Tape
Hammer Ratchet 1/2”,
7/16” & 9/16”
Square
Ruler
Step
Ladder
12342X Post 2 x 4 x 83”

1 inch = 25.4mm
SOLO)WAVE DESIGN HARDWARE
For example:
BOLT LENGTH 4½ (4.5) inches long
114mm long
1 inch = 25.4mm
25.4mm
4.5 inches x
DIAMETER CONVERSION
LENGTH CONVERSION
=
BOLT DIAMETER 5/16 (0.31) inches
0.31 inches x 25.4mm = 8mm
For example:
HARDWARE LENGTH CHART
inches vs millimetres
6 152
5½ 140
5 127
4½ 114
4 102
3½ 89
3 76
2½ 64
2 51
1½ 38
1¼ 32
1-1/8 29
1 25.4
7/8 22
3/4 19
1/2 12.7
1/4" (6mm) Flat Washer
1/4" (6mm)
Lock Washer
1/4"(0.25) = 6mm Hex Bolt
1/4" (6mm)
T-Nut
5/16"(.31) = 8mm Lag Screw
5/16" (8mm)
Flat Washer
1/4"(0.25) = 6mm Lag Screw
1/4" (6mm)
Flat Washer
5/16" (8mm)
Flat Washer
5/16" (8mm) Lock Washer
5/16"(.31) = 8mm Hex Bolt
5/16" (8mm)
T-Nut
3/8"(.38) = 9.5mm Lag Screw
3/8" (9.5mm)
Flat Washer

1 x 2
1 x 4
1 x 5
1 x 6
1 x 3
1/2 x 4
5/4 x 6
5 1/2"
139.7
1"
25.4
11.1
.44
82.6
3 1/4"
4 x 4
3 1/2"
88.9
3 1/2"
88.9
4 1/2"
114.3
5/8"
15.9
15.9
5/8" 1 3/8"
34.9
2 x 6
5 3/8"
136.5
1 1/2"
38.1
15.9
5/8" 3 3/8"
85.7
60.3
2 3/8"
15.9
5/8"
1505mm
SOLO)WAVE DESIGN WOOD PROFILES
LENGTH CONVERSION
For example:
1 inch = 25.4mm
BOARD LENGTH 59¼ (59.25) inches
59.25 inches x 25.4mm =
Dimensions in brackets
[mm] represent millimetres.
5/4 x 4
3 1/2"
88.9
1"
25.4
5 3/8"
136.5
5/8"
15.9
2 x 4
3 3/8"
85.7
1 3/8"
34.9
5/4 x 5
4 1/2"
114.3
1"
25.4 2 x 3
2 1/2"
63.5
1 3/8"
34.9
5/4 x 3
63.5
2 1/2"
25.4
1"
2
x 2
1 1/2"
38.1
1 1/2"
38.1

Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
1pc. -2162 - Siding Clock 3/8 x 3-1/2 x 49-1/8" - Box 2 - 3632162
8pc. -2116 - Siding 3/8 x 3-1/2 x 38-3/4" - Box 2 - 3632116
4pc. -2159 - Siding 3/8 x 3-1/2 x 29-5/16" - Box 2 - 3632159
3pc. -2051 - Door Siding 3/8 x 3-1/2 x 11-3/8" - Box 2 - 3602051
1pc. -2050 - Door Siding Top 3/8 x 3-1/2 x 11-3/8" - Box 2 - 3602050
1pc. -2160 - Narrow Siding 3/8 x 3 x 29-5/16" - Box 2 - 3632160
2pc. -2155 - Siding Narrow 3/8 x 3 x 38-3/4" - Box 2 - 3632155
2pc. -1740 - Window Brace 1 x 2 x 9-1/2" - Box 3 - 3641740
2pc. -2052 - Door Cross 1/2 x 3 3/8 x 15-7/16" - Box 2 - 3602052
20pc. -2156 - Roofing 3/8 x 3 1/2 x 53-13/16" - Box 2 - 3632156
6pc. -2128 - Siding 3/8 x 3-1/2 x 49-1/8" - Box 2 - 3632128
Part Identification (Reduced Part Size)
Nominal Size
½ x 4
1 x 2
1 x 3
1 x 4
Actual Size
7
16" x 3¼"
⅝" x 1⅜"
⅝" x 2⅜"
⅝" x 3⅜"
1pc. -2053 - Door Arch 1/2 x 4 1/2 x 15-7/16" - Box 2 - 3602053
2pc. -0389 - Window Frame 1 x 2 x 16 1/4" - Box 3 - 3630389
2pc. -2118 - Front Trim 1 x 2 x 23 3/8" - Box 3 - 3632118

8pc. -2158 - Cedar Floor Board 1 x 5 x 38-3/4" - Box 3 - 3632158
2pc. -2104 -Middle Gap Board 1 x 5 x 38-3/4" - Box 3 - 3632104
Part Identification (Reduced Part Size)
1pc. -1205 -CE Access Wall 1 x 4 x 41 3/4" - Box 3 - 3631205
1pc. -2108 - Left Roof Board 1 x 4 x 30" - Box 3 - 3632108
Actual Size
⅝" x 3⅜"
⅝" x 4½"
⅝" x 5⅜"
Nominal Size
1 x 4
1 x 5
1 x 6
Part Identification (Reduced Part Size)
3pc. -2144 -Lower Bench 1 x 4 x 38 7/8" - Box 2 - 3632144
7pc. -2133 - Trim 5/8 x 1 3/4 x 16-1/4" - Box 3 - 3632133
1pc. -0850 - CE Wall Board 1 x 4 x 17" - Box 3 - 3630850
12pc. -5265 - Cedar Wall 1 x 4 x 28" - Box 3 - 3635265
1pc. -2109 - Right Roof Board 1 x 4 x 30" - Box 3 - 3632109
1pc. -2136 - CE Gap Board 1 x 4 x 38 3/4" - Box 3 - 3632136
1pc. -2114 -Top Front 1 x 4 x 52" - Box 3 - 3632114
1pc. -2145 -Back Top 1 x 4 x 52" - Box 3 - 3632145
1pc. -2127 -Side Ground 1 x 5 x 38-3/4" - Box 2 - 3632127
1pc. -2134 -Cedar Gap Board 1 x 5 x 38-3/4" - Box 2 - 3632134

Part Identification (Reduced Part Size)
2pc. -2149 -Top Bottom Rockwall 1 x 6 x 19-3/4" - Box 3 - 3632149
1pc. -2157 - Ground SW Side 1 x 5 x 81 1/8" - Box 3 - 3632157
Actual Size
⅝" x 4½"
⅝" x 5⅜"
1" x 1⅜"
1" x 2½"
1" x 3½"
Nominal Size
1 x 5
1 x 6
5/4 x 2
5/4 x 3
5/4 x 4
Part Identification (Reduced Part Size)
4pc. -0631 - CE Rock Board 1 x 6 x 19-3/4" - Box 3 - 3630631
1pc. -2143 - Middle Back 1 x 5 x 65-5/8" - Box 3 - 3632143
2pc. -2150 - Front Back Ground 1 x 5 x 67" - Box 3 - 3632150
2pc. -2119 - Oval Window 1 x 6 x 8-1/4" - Box 3 - 3632119
4pc. -0630 - CE Rock Board 1 x 6 x 19-3/4" - Box 3 - 3630630
2pc. -2147 -End Board 1 x 6 x 38 3/4" - Box 2 - 3632147
1pc. -2139 -SW Wall Support 5/4 x 2 x 23 1/2" - Box 3 - 3632139
1pc. -2111 -Ladder Top 5/4 x 3 x 35-1/4" - Box 3 - 3632111
2pc. -2121 -Gable Bottom 5/4 x 3 x 35-7/8" - Box 3 - 3632121
1pc. -2107 - Door Stop 5/4 x 4 x 10" - Box 3 - 3632107
2pc. -2113 -Gusset II 5/4 x 4 x 18-1/2" - Box 3 - 3632113
1pc. -2125 -Middle Front 1 x 5 x 65-5/8" - Box 3 - 3632125

Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
2pc. -2105 -Bench Post 5/4 x 4 x 14" - Box 2 - 3632105
1pc. -2151 -Back Wall Support 5/4 x 4 x 31" - Box 3 - 3632151
1pc. -2131 -Front Table Top 5/4 x 4 x 32-1/16" - Box 3 - 3632131
1pc. -2103 -Lower Floor Support 5/4 x 4 x 38-7/8" - Box 2 - 3632103
1pc. -1862 -SW Support 5/4 x 4 x 46-1/2" - Box 2 - 3641862
1pc. -2115 -Chalkwall Top 5/4 x 4 x 52" - Box 2 - 3632115
1pc. -2123 -Back Floor 5/4 x 4 x 67" - Box 2 - 3632123
2pc. -2138 -Seat Side 5/4 x 5 x 5-1/2" - Box 2 - 3632138
1pc. -2106 -SW Top 5/4 x 5 x 38-3/4" - Box 2 - 3632106
1pc. -2126 -SW Floor 5/4 x 5 x 38-3/4" - Box 2 - 3632126
1pc. -2124 -Front Floor 5/4 x 5 x 67" - Box 3 - 3632124
1pc. -2141 -Café Top 5/4 x 6 x 40-7/8"- Box 2 - 3632141
1pc. -2148 -Bench 5/4 x 6 x 42-1/2" - Box 2 - 3632148
2pc. -2132 -Roof Support Left 2 x 3 x 33-9/16" - Box 2 - 3632132
2pc. -2146 -Roof Support Right 2 x 3 x 33-9/16" - Box 2 - 3632146
1pc. -0369 -Lower Diagonal 2 x 3 x 37" - Box 3 - 3640369
Actual Size
1" x 3½"
1" x 4½"
1" x 5½"
1⅜" x 2½"
Nominal Size
5/4 x 4
5/4 x 5
5/4 x 6
2 x 3

Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
Actual Size
1½" x 1½"
1⅜" x 2½"
1⅜" x 3⅜"
Nominal Size
2 x 2
2 x 3
2 x 4
1pc. -2117 -Rock Rail 2 x 3 x 56-1/8" - Box 3 - 3632117
2pc. -2120 -Floor Front Back 2 x 3 x 64-1/4" - Box 2 - 3632120
1pc. -2142 -Floor Joist 2 x 3 x 65-5/8" - Box 2 - 3632142
2pc. -2112 -SL Post 2 x 4 x 32-1/2" - Box 2 - 3632112
2pc. -1863 -SW Post 2 x 4 x 86-11/16" - Box 3 - 3641863
1pc. -2122 -SL Floor End 2 x 4 x 38-7/8" - Box 2 - 3632122
2pc. -2152 -Roof Support 2 x 2 x 29-1/4" - Box 3 - 3632152
4pc. -2153 -Post 2 x 4 x 96-1/2" - Box 2 - 3632153
2pc. -2135 -Wall Support 2 x 2 x 22-1/4"- Box 2 - 3632135
1pc. -2102 -Front Table Support 2 x 2 x 32" - Box 2 - 3632102
2pc. -2161 -Roof Joist 2 x 2 x 32-5/16" - Box 3 - 3632161
1pc. -2101 -Access Rail Left 2 x 3 x 56-1/8" - Box 3 - 3632101
1pc. -2100 -Access Rail Right 2 x 3 x 56-1/8" - Box 2 - 3632100
1pc. -4919 -SW Rail Block 2 x 4 x 5-3/8" - Box 2 - 3644919
1pc. -2130 -SW Mount 2 x 4 x 34-1/2" - Box 2 - 3632130
1pc. -1856 -SW Upright 2 x 4 x 48-5/16" - Box 2 - 3641856
1pc. -2129 -Café Support 2 x 2 x 40-3/8" - Box 3 - 3632129

1pc. -2058 -Door Side Left 1 1/4 x 3 x 40 1/8 " - Box 3 - 3602058
1pc. -2057 -Door Side Right 1 1/4 x 3 x 40 1/8" - Box 3 - 3602057
4pc. -1578 - Dowel Tennion 1-1/8 x 15-7/8" - Box 1 - 3681578
5pc. -0318 - Ground Stake 2 x 2 x 14" - Box 1 - 3650318
1pc. -2137 - SL Upright 2 x 3 x 48-1/2" - Box 1 - 3632137
1pc. -2110 - SL Ground 1 x 5 x 44-3/4" - Box 1 - 3632110
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)
Actual Size
1½" x 1½"
1½" x 5⅜"
Nominal Size
2 x 2
2 x 6
2pc. -2154 -Front Post 2 x 2 x 94" - Box 2 - 3632154
1pc. -1825 - Back Beam 2 x 6 x 83-5/8" - Box 3 - 3631825
1pc. -1826 - Front Beam 2 x 6 x 83-5/8" - Box 3 - 3631826
1pc. -4909 - SW Block 5/4 x 4 x 3-1/2" - Box 1 - 3644909
1pc. -2140 - Short Upright 2 x 3 x 33" - Box 1 - 3632140

2pc. H0 -HexBolt1/4x1"-(9277210)
6pc. H15 -HexBolt1/4x3-3/4"-(53702233)
4pc. H12 -HexBolt1/4x3"-(9277230)
Hardware Identification(ActualSize)
10pc. H4 -HexBolt1/4x4"-(9277240)
7pc. LS3 -LagScrew1/4x3"-(9262230)
1pc. H8 -HexBolt1/4x4-1/4"-(9277241)
1pc. LS2 -LagScrew1/4x2-1/2"-(9272222)
8pc. H5 -HexBolt1/4x4-1/2"-(9277242)
4pc. H1 -HexBolt1/4x1-1/2"-(9277212)
4pc. H7 -HexBolt1/4x5-1/2"-(9277252)
2pc. LS1 -LagScrew1/4x1-1/2"-(9262212)
4pc. H6 -HexBolt1/4x4-3/4"-(9277243)
23pc. H2 -HexBolt1/4x2"-(9277220)

2pc. G4 -HexBolt5/16x4"-(9277340)
7pc. G5 - HexBolt5/16x4-1/2"-(9277342)
4pc. G7 -HexBolt5/16x5-1/2"-(9277352)
2pc. Z -HexBolt5/16x6"-(9277360)
2pc. G8 -HexBolt5/16x2"-(9277320)
4pc. G1 -HexBolt5/16x1-1/2"-(9277312)
Hardware Identification(ActualSize)

39pc. S7 -PanScrew#12x2"-(9264620)
Hardware Identification(ActualSize)
5pc. S6 -PanScrew#12x1"-(9264610)
18pc. S10 -PanScrew#8x1"-(9264510)
143pc. S0 / S22 -TrussScrew#8x7/8"-(9229505)
8pc. PB2 -PanBolt1/4x1-1/4"-(9274211)
13pc. LW2 -5/16"LockWasher-(9253300)
12pc. LN2 -5/16"LockNut- (9283300)
13pc. TN2 -5/16"T-Nut- (9285300)
8pc. BN1 -1/4"BarrelNut-(9248200)
66pc. TN1 -1/4"T-Nut-(9285200)
74pc. LW1 -1/4"LockWasher-(9253200)
37pc. FW2 -5/16"FlatWasher-(9251300)
92pc. FW1 -1/4"FlatWasher-(9251200)
15pc. FW0 -3/16"FlatWasher-(9251100)
19pc. S8 -PanScrew#12x3/4"-(9264603)
146pc. S2 -WoodScrew#8x1-1/2"-(52042512)
22pc. S15 -WoodScrew#8x1-3/4"-(52043513)
96pc. S1 -WoodScrew#8x1-1/8"-(52042514)
33pc. S3 -WoodScrew#8x2-1/2"-(52042522)
11pc. S4 -WoodScrew#8x3"-(52042530)
4pc. S18 -WoodScrew#6x1"-(9260910)
40pc. S13 -PanScrew#6x5/8"-(9264990)

2X 3320184 Rocks (4pk)
2-Green 2-Yellow
1X 3200202
Glider Hanger (2pk)
1X 3320356
Big Backyard I.D
Plaque w hardware
2X 3724943
42" Belt Swing Yellow
w.welded chain
Part Identification (Reduced Part Size)
1X 3320715
Spin Chalk Sign
2X 9320240
Hand Grip
1X 3202000
Swing Hanger
Bolt Thru. (4 pk)
1X 3533860
39" Glider Rope & Chain
(4pk) w. welded chain
1X 3320124
Clock Assembly
1X 9320146
Small Window
2X 3320172
2 person Glider End
1X 3201710
Door Hardware
2X 9320175
Arch Top Window
1X 9200014
#2 Robertson
Driver
1X 3320121
Peak Detail (2Pk)
1X 3310103
Spiral Wave Slide Bottom
(Green)
1X 3320273
2 person Glider Seat
1X 3320351
Big Backyard
Plaque
1X 9320148
Oval Window
1X 3310101
Spiral Wave Slide Top
(Green)
2X 9201500
Spiral Wave
Bracket
1X 3200184
Triangle Plate (4pk)

1-877-966-3738
B.Ifthereareanymissingordamagedpiecesoryouneedassistancewith
assemblypleasecontacttheConsumerRelationsDepartmentdirectly.Callus
beforegoingbacktothestore.
STOP STOPSTOP STOP
Step 1: Inventory Parts - Read This Before Starting Assembly
C. Readtheassemblymanualcompletely,payingspecialattentiontoANSIwarnings;
notes;andsafety/maintenanceinformationonpages1-6.
D. Beforeyoudiscardyourcartonsllouttheformbelow.
•ThecartonI.D.stampislocatedontheendofeachcarton.Thetrackingnumberis
locatedontheBigBackyardIDPlaque(3320356).
•Pleaseretainthisinformationforfuturereference.Youwillneedthisinformationifyou
contacttheConsumerRelationsDepartment.
•PleaserefertoPage6forproperhardwareassembly.
•Eachstepindicateswhichboltsand/orscrewsyouwillneedforassembly,aswellas
anyatwashers,lockwashers,t-nutsorlocknuts.
A.Thisisthetimeforyoutoinventoryallyourhardware,woodandaccessories,
referencingthepartsidenticationsheets.Thiswillassistyouwithyourassembly.
•Thewoodpieceswillhavethefourdigitkeynumberstampedontheendsofthe
boards.Thewoodpiecesarereferencedthroughouttheinstructionswiththisnumber.
CARTONI.D.STAMP:__________14459___(Box4)
CARTONI.D.STAMP:__________14459___(Box5)
CARTONI.D.STAMP:__________14459___(Box6)
CARTONI.D.STAMP:__________14459___(Box1)
CARTONI.D.STAMP:__________14459___(Box2)
CARTONI.D.STAMP:__________14459___(Box3)
MODELNUMBER:F23073C
TRACKINGNUMBER(fromIDPlaque):

1 x Access Rail Right 2 x 3 x 56-1/8”
1 x Access Rail Left 2 x 3 x 56-1/8”
4 x Tennon Dowel 1-1/8 x 15-7/8”
1578
2101
2100
Fig. 2.1
Wood Parts Hardware
Step 2: Access Ladder / Rockwall Assembly
Part 1
Pre-drill all pilot holes using a 1/8” drill bit before installing wood screws.
A:Insert4(1578)1-1/8x15-7/8”Dowelsinto(2100)AccessRailRightand(2101)AccessRailLeftasshownin
g.2.1.
B:Makesureshoulderofdowelisagainsteachrailbeforepre-drillingpilotholes.Drill1/8”pilotholesthroughthe
railsandintothedowelstopreventsplitting.(g.2.1)
C:Attach(1578)1-1/8x15-7/8”Dowelstobothrailswith2(S2)#8x1-1/2”WoodScrewsperdowel.(g.2.1)
8 x #8 x 1-1/2” Wood Screw
1578
2101
Left Side
Right Side
S2
2100
S2 x8 1578
This manual suits for next models
2
Table of contents
Other Big Backyard Baby Accessories manuals
Popular Baby Accessories manuals by other brands

Koru Kids
Koru Kids JUNIOR BOOSTER Instructions for use

Lascal
Lascal Buggyboard-Mini owner's manual

Inglesina
Inglesina Kit Auto Pro 3P instruction manual

Fisher-Price
Fisher-Price Miracles & Milestones K4067 instruction sheet

bbluv
bbluv Sunkito quick start guide

BEBE CONFORT
BEBE CONFORT FamilyFix user manual