Big Lots HARLOW 6PCS DINING SET User manual

BIG LOTS
ASSEMBLY INSTRUCTIONS
1
HARLOW 6PCS DINING SET
ITEM NO. 15100-6PK
SKU NO. 810321491
Big Lots Customer Care
Phone # : 1-866-BIGLOTS(1-866-244-5687)
Email Add : [email protected]
'For spare screw and bolts, please contact big lots customer care'

2
GENERAL INFORMATION, TIPS & TRICKS
1. Please read the assembly instructions prior to assembling this product.
2. To avoid damages, assemble this product on a non-abrasive surface such as carpet.
3. Make sure all bolts and nuts are tightly fastened before the product is used.
4. Not for commercial use.
5. Care: Wipe with a damp cloth. Use furniture polish or lemon oil on the wood as
needed. Avoid prolonged exposure to moisture.
Please make sure you have all parts before beginning assembly. Please wait until
all steps are completed before tightening bolts. We recommend two people to
assemble.
A phillips head screwdriver is necessary for assembly.
Do not put hot post or objects which are more than 80
degrees Fahrenheit directly on the table surface.

TABLE PART LIST
3
A. TABLE TOP 1 PC
B. TABLE LEG 4 PCS
TABLE HARDWARE LIST
1. FLAT WASHER
SIZE: 5/16" DIA
QTY: 8 PCS
2. SPRING WASHER
SIZE: 5/16" DIA
QTY: 8 PCS
3. BOLT
QTY: 8 PCS
4. OPEN WRENCH
QTY: 1 PC
A
B
SIZE: 5/16" x 3" SIZE: #12mm

4
TABLE ASSEMBLY INSTRUCTIONS
1.Place table top (A) upside
down on a non-abrasive surface
such as carpet (underside of
tabletop should be facing up ).
2. Attach the legs (B) to the
apron of table top (A) using 8
flat washers (1), 8 spring
washers (2), and 8 bolts (3) as
shown.
DIAGRAM #1
REQUIRED HARDWARE IN THIS STEP
NO
1
2
3
4
FLAT WASHER 8 PCS
SKETCH QTY
DESCRIPTION
SPRING WASHER
BOLT
OPEN WRENCH 1 PC
A
B
B
8 PCS
8 PCS

5
TABLE ASSEMBLY INSTRUCTIONS
DIAGRAM #2
The Table is now ready for use
3. With assistance, carefully turn the table upright. Ensure the table is level and
tighten all bolts (3) using the open wrench (4).

CHAIR PART LIST
6
C. CHAIR BACK 4 PCS
D. SEAT FRAME 4 PCS
E. FRONT LEG 8 PCS
F. CUSHION 4 PCS
CHAIR HARDWARE LIST
1. FLAT WASHER
SIZE: 5/16" DIA
QTY: 44 PCS
2. SPRING WASHER
SIZE: 5/16" DIA
QTY: 44 PCS
3. BOLT
SIZE: 1/4" x 1-3/4"L
QTY: 12 PCS
4. BOLT
QTY: 1 PCQTY: 16 PCS
5. BOLT 6. OPEN WRENCH 7. WOOD SCREW
QTY: 24 PCS
SIZE: 4 x 38
C
D
E
E
F
SIZE: 1/4" x 3-3/8"L
SIZE: 1/4" x 2-5/9"L
QTY: 16 PCS
SIZE: #12mm

CHAIR ASSEMBLY INSTRUCTIONS
7
DIAGRAM #3 REQUIRED HARDWARE IN THIS STEP
NO
1
2
4
6
FLAT WASHER 4 PCS
SKETCH QTY
DESCRIPTION
SPRING WASHER
BOLT
1 PC
1.Attach 2 front legs (E) to seat frame (D) using 4 bolt (4), 4 spring washers (2)
and 4 flat washers (1) as shown.
Note. The seat frame (D) has two screw holes on each side which are
used to attach the cushion (F) to the seat frame (D). The holes are
wider on the bottom side of the seat frame (D) and should be facing up
when attaching the front legs (E).
OPEN WRENCH
D
4 PCS
4 PCS

8
DIAGRAM #4
2. Attach the seat frame (D) to the chair back (C) using 3 short bolts (3), 4 bolts (5),
7 spring washers (2) and 7 flat washers (1) as shown. Do not fully tighten.
3. Turn the chair upright. Make sure the assembled chair unit is level and square.
Tightly fasten all bolts (3 & 5) with the open wrench (6).
321
6
621
4
REQUIRED HARDWARE IN THIS STEP
NO
1
2
3
6
FLAT WASHER 7 PCS
SKETCH QTY
DESCRIPTION
SPRING WASHER
BOLT
7 PCS
3 PCS
OPEN WRENCH 1 PC
5BOLT 4 PCS
C
D
E
C
D
E
E
E
CHAIR ASSEMBLY INSTRUCTIONS

9
REQUIRED HARDWARE IN THIS STEP
NO
7
SKETCH QTY
DESCRIPTION
4. Place cushion (F) upside down on a non-abrasive table surface. The
rear (tapered end) of the cushion (F) should be near the table edge.
Hint: Protect the non-abrasive table surface and cushion (F) by placing
a towel between the table and cushion.
5. Place the assembled chair frame on the cushion (F) as shown.
Make sure the cushion (F) is centered and tight against the chair
frame. Attach the cushion (F) to the chair frame using 6 wood screws
(7). Fully tighten all screws.
6 PCS
WOOD SCREW
C
E
F
77
CHAIR ASSEMBLY INSTRUCTIONS
DIAGRAM #5
D

10
The dining chair is now ready for use.
6. Repeat diagram #3 to #6 to assemble the other chairs.
CHAIR ASSEMBLY INSTRUCTIONS
DIAGRAM #6

BENCH PART LIST
BENCH HARDWARE LIST
1. FLAT WASHER
SIZE: 5/16" DIA
QTY: 8 PCS
2. SPRING WASHER
SIZE: 5/16" DIA
QTY: 8 PCS
3. BOLT
QTY: 8 PCS
4.OPEN WRENCH
QTY: 1 PC
5. WOOD SCREW
QTY: 8 PCS
SIZE: 4 x 38
11
G. SEAT FRAME 1 PC
E. FRONT LEG 4 PCS
H. CUSHION 1 PC HE
E
EG
SIZE: 1/4" x 2-5/9"L SIZE: #12mm

BENCH ASSEMBLY INSTRUCTIONS
12
REQUIRED HARDWARE IN THIS STEP
NO
1
2
4
FLAT WASHER 8 PCS
SKETCH QTY
DESCRIPTION
SPRING WASHER
BOLT
8 PCS
8 PCS
DIAGRAM #7
1. Attach 4 front legs (E) to seat frame (G) using 8 bolt (4), 8 spring washers (2) and 8
flat washers (1) as shown.
Note. The seat frame (G) has eight screw holes, which are used to
attach the seat. These holes are wider on the bottom and narrower on
the top. Ensure the wider holes are facing towards the bottom of the
bench.
1
GE
E
E
61 PC
OPEN WRENCH
78 PCS
WOOD SCREW

13
4. Place cushion (H) upside down on a non-abrasive table surface.
Hint: Protect the non-abrasive table surface and cushion (H) by placing
a towel between the table and cushion.
5. Place the assembled bench frame on the cushion (H) as shown.
Make sure the cushion (H) is centered. Attach the cushion (H) to the
bench frame using 8 wood screws (7). Fully tighten all screws.
REQUIRED HARDWARE IN THIS STEP
NO
7
SKETCH QTY
DESCRIPTION
8 PCS
WOOD SCREW
H
G
5
DIAGRAM #8
E
E
E
E
BENCH ASSEMBLY INSTRUCTIONS

14
The bench is now ready for use.
Printed in Viet Nam
DIAGRAM #9
BENCH ASSEMBLY INSTRUCTIONS