Big Lots BIG-178 User manual

Big Lots Customer Care
Phone #: 1-866-BIGLOTS(1-866-244-5687)
Email Add: [email protected]
SKU NO. 810110498
ASSEMBLY INSTRUCTIONS
1
6PCS PU DINING SET
BIG LOTS
ITEM NO. BIG-178
'For spare screws and bolts, please contact big lots customer care'

Please make sure you have all parts before beginning assembly. Please wait
until all steps are completed before tightening bolts. We recommend two
people to assemble.
A Phillips head screwdriver is necessary for assembly.
5. Care: Wipe with a damp cloth. Use furniture polish or lemon oil on the
wood as needed. Avoid prolonged exposure to moisture.
4. Not for commercial use.
3. Make sure all bolts and nuts are tightly fastened before the product is used.
2. To avoid damages, assemble this product on a non-abrasive surface such as carpet.
1. Please read the assembly instructions prior to assembling this product.
GENERAL INFORMATION, TIPS & TRICKS
2
Do not put hot pots or objects which are more than
Fahrenheit 80 degrees directly on the table.

3
TABLE PART LIST
A. TABLE TOP 1 PC
B. TABLE LEG 4 PCS
TABLE HARDWARE LIST
1. FLAT WASHER 2. SPRING WASHER 3. NUT 4. OPEN WRENCH
SIZE: 5/16" DIA
QTY: 8 PCS
SIZE: 5/16" DIA
QTY: 8 PCS
SIZE: 5/16" DIA
QTY: 8 PCS
SIZE: 5/16" DIA
QTY: 1 PC
A
B

5
TABLE ASSEMBLY INSTRUCTIONS
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
1. 8 PCS
SPRING WASHER
2. 8 PCS
NUT
3. 8 PCS
OPEN WRENCH
4. 1 PC
FLAT WASHER
3. Attach the legs (B) to the apron
of table top (A) using 8 flat
washers (1), 8 spring washers (2),
and 8 nuts (3) as shown.
DIAGRAM #1
A
B
B
1
2
3
4

6
TABLE ASSEMBLY INSTRUCTIONS
DIAGRAM #2
3. Turn the table upright. Make sure the table is level, and tightly fasten
all nuts (3) using the open-end wrench (4) as shown.
The Table is now ready for use

CHAIR PART LIST
C. CHAIR BACK 4 PCS
D. SEAT FRAME 4 PCS
E. FRONT LEG 8 PCS
F. SEAT BOARD 4 PCS
7
1. FLAT WASHER 2. SPRING WASHER 3. NUT 4. OPEN WRENCH
SIZE: 5/16" DIA
QTY: 44 PCS
SIZE: 5/16" DIA
QTY: 44 PCS
SIZE: 5/16" DIA
QTY: 16 PCS
SIZE: 5/16" DIA
QTY: 1 PC
CHAIR HARDWARE LIST
SIZE: 1-3/4" L x 1/4" DIA
5. SHORT BOLT 6. LONG BOLT 7. WOOD SCREW
QTY: 12 PCS
SIZE: 3" L x 1/4" DIA
QTY: 16 PCS
SIZE: #8 x 1-1/2" L
QTY: 24 PCS
C
F
E
E
D

8
DIAGRAM #3
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
1. 4 PCS
SPRING WASHER
2. 4 PCS
NUT
3. 4 PCS
FLAT WASHER
CHAIR ASSEMBLY INSTRUCTIONS
1. Attach 2 front legs (E) to seat frame (D) using 4 nuts (3), 4 spring
washers (2) and 4 flat washers (1) as shown.
Note: The seat frame (D) has two screw holes on each side,
which are used to attach the seat. These holes are wider
on the bottom and narrower on the top. Ensure the wider
holes are facing towards you.
4
3
2
1
3
2
1
E
D
E
E
3
2
1

C
9

4. Place seat board (F) upside down on a non-abrasive table
surface . The rear (tapered end) of the seat board (F) should
be near the table edge.
Hint: Protect the non-abrasive table surface and seat board
(F) by laying a towel in-between the seat board and table.
5. Place the assembled chair frame on the seat board (F) as
shown. Attach with 6 wood screws (7). Tighten the screws.
7
77
7
7
7D
F
C
10

11

BENCH PART LIST
G. CUSHION 1 PC
12
1. FLAT WASHER 2. SPRING WASHER 3. NUT 4. OPEN WRENCH
SIZE: 5/16" DIA
QTY: 8 PCS
SIZE: 5/16" DIA
QTY: 8 PCS
SIZE: 5/16" DIA
QTY: 8 PCS
SIZE: 5/16" DIA
QTY: 1 PC
BENCH HARDWARE LIST
7. WOOD SCREW
SIZE: #8 x 1-1/2" L
QTY: 8 PCS
G
E
E
E
E
H
E. FRONT LEG 4 PCS
H. SEAT FRAME 1 PC

13
DIAGRAM #7
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
1. 8 PCS
SPRING WASHER
2. 8 PCS
NUT
3. 8 PCS
FLAT WASHER
BENCH ASSEMBLY INSTRUCTIONS
1. Attach 4 front legs (E) to seat frame (H) using 8 nuts (3), 8 spring
washers (2) and 8 flat washers (1) as shown.
Note: The seat frame (H) has several screw holes on each side,
which are used to attach the cushion. These holes are wider
on the bottom and narrower on the top. Ensure the wider
holes are facing towards you.
E
3
2
1
OPEN WRENCH
4. 1 PC

14
BENCH ASSEMBLY INSTRUCTIONS
DIAGRAM #8
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
7. 8 PCS
WOOD SCREW
4. Place cushion (G) upside down on a non-abrasive table
surface.
Hint: Protect the non-abrasive table surface and cushion
(G) by laying a towel in-between the cushion and table.
5. Place the assembled bench frame on the cushion (G) as
shown. Attach with 8 wood screws (7). Tighten the screws.

15
BENCH ASSEMBLY INSTRUCTIONS
DIAGRAM #9
The bench is now ready for use.
Printed in Vietnam