Big Lots 810169935 User manual

FOOT CAP
Page 1
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
PARTS LIST ORDER PART # Article#810169935DESCRIPTION
AFOOT CAP
FACTORY ASSEMBLY
REPLACEMENT PARTS LIST
SZ055

IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION
SHEET BEFORE ASSEMBLY!!
TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP
INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT
Step 1: Remove all protective materials and set parts on a flat non-abrasive surface to avoid scratching.
Identify all parts packed in carton against the parts list.
Step 2: It is recommended that two people work together to assemble this product. Using four
1/4"x35 mm bolts(E) and Ø6.5 x 1.0 mm washers(F), attach the front frame(B) to the sofa
frame(A) beneath each leg as shown in Fig.1. Do not over tighten.
Fig.1
QTY
F
1
2
1
PARTS LIST DESCRIPTION ORDER PART # QTY
FOOT CAP
FACTORY ASSEMBLY
NSST105AB-7
SZ0234
FOOT CAP
FACTORY ASSEMBLY
Page 2
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
DESCRIPTION ORDER PART #
1/4" X 20 MM BOLT SC111X020
SOFA FRAME
4
1/4" X 35 MM BOLT SC111X035
FRONT FRAME
1
HEX BOLT DRIVER SE00F1994
PARTS LIST
A
B
C
D
E
6
Ø6.5 X 1.0 MM
WASHER SE00F1991
A
B
E
F
EF

Step 5: Your sofa is ready for use.
Page 3
Step 3: Attach the front frame(B) to the underside of the sofa frame(A) by using two 1/4"x20 mm
bolts(D) and Ø6.5 x 1.0 mm washers(F) as shown in Fig 2. Guide the bolts through the holes
in the front frame, into the pre-drilled holes underside of the sofa seat frame. Do not over
tighten.
Fig.2
Step 4: Tighten all bolts using the hex bolt driver(C) provided. Tighten each bolt a few revolutions
at a time, alternating between bolt connections until all bolts are tight. Do not over tighten.
Over tightening may strip bolts or damage the welds or frame.
F
DB
F
D

Page 4
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION
SHEET BEFORE ASSEMBLY!!
TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP
INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT
Step 1: Remove all protective materials and set parts on a flat, non-abrasive surface. Identify parts
packed in carton against the parts list.
Step 2: Place the table top (A) upside down on a flat, non-abrasive surface. Attach the table leg to
the table top by using the 1/4"x20 mm boltS(D) and washers(F) as shown in Fig. 1. Guide the
bolt through the hole in the table leg , into the pre-drilled hole in the table top. Hand tighten
only. Repeat for the other three legs.
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
DESCRIPTION ORDER PART # QTY
G
H
I
J
K
PARTS LIST
A
B
C
D
E
F
PARTS LIST DESCRIPTION ORDER PART # QTY
PORCELAIN TILE
TABLE TOP
LEG CONNECTOR
BRACKET 1
TABLE LEG 4
1/4" X 20 MM BOLT 4
SC111X020
Ø6.5 X 1.0 MM
WASHER 12
SE00F1991
SZ043
BOLT COVER 4
HEX BOLT DRIVER 1
SE00F1994
FOOT CAP
FACTORY ASSEMBLY SZ0138
1
1/4" NUT NQ11 8
NUT COVER SZ092 8
HEX WRENCH SE00F4444 1
Fig.1
A
F
D
G
FOOT CAP
C
METAL PLATE SE00F4648 4

Page 5
Step 3: Attach the table leg(C) to the leg connector bracket(B) by carefully guiding the bolts already in
place on the table legs (each leg has two bolts) through the holes in the leg connector bracket
as shown in Fig. 2 . Add a metal plate(I), and add a washer(F) with nut(E) to the end of each
bolt. Hand tighten only. Do not tighten completely. Repeat on the other three legs.
Fig.2
Step 4: After making any necessary adjustments to the alignment of the table legs and the leg
connector bracket, use the hex bolt driver(K) and hex wrench(J)to tighten all nuts and bolts.
Note: each bolt and nut must be tightened a few revolutions at a time. In order to apply equal
pressure to all bolt joints, we recommend working in a cross corner (X fashion). Repeat until
all bolts are tight. Do not over tighten. Over tightening may strip bolts. Cover all bolts and
nuts with covers(G and H).
Step 5: With the help of another person, turn the table in the upright position. Your table is now ready
for use.
Fig.1Fig.1
A
B
C
E
F
H
I