Billy Goat BLOWER QB882 Installation instructions

Part No. 430187 Form No. F060496C
Page 1 of 8
33
33
3
Specifications
QB882 QB882IC QB882H Q B882CARB QB1102IC QB1102H
ENGINE: HP 8.0 HP (5.97 kW) 8.0 (5.97 kW) 8.0 (5.97 kW) 11.0 HP (8.kW) 11.0 HP (8.2kW) 11.0HP(8.2kW)
ENGINE:TYPE B & S B & S IC HONDA OHV B & S IN. PLUS B & S IC HONDA OHV
ENGINE: FUEL CAP. 4.0 qt. ( 3.8 L) 4.0 qt (3.8 L) 6.4 qt. (6.1 L) 4.0 qt. (6.1L) 6.0 qt. (5.7 L) 7.4 qt. ( 7.0 L)
ENGINE: OIL CAP. 1.38 qt. (1.3 L) 1.38 qt. (1.3 L) 1.16 qt. (1.1 L) 1.16 pt. (1.1L) 1.5 qt. ( 1.4 L) 1.2 qt.(1.13L)
WEIGHT:UNIT 124 # ( 56.3 Kg) 126 # (57.2 Kg) 136 # (61.7 Kg) 126 # (57.2 Kg) 150 # (68.0 Kg) 152 # (68.9 Kg)
WEIGHT:SHIPPING 141 # (63.97 Kg) 143 # (64.9Kg) 153 # (69.4 Kq) 143 # (64.9 Kg) 167 # (75.8 Kg) 169 # (76.7 Kg)
ENGINEWEIGHT: 46 # (20.8 Kg) 49 # (22.2 Kg) 48.5 # (22.0 Kg) 49 # (22.2 Kg) 64.25# (29.1 Kg) 68.4 #(31.0 Kg)
UNITSIZE: OVERALL LENGTH: 51.75"(1.31m) OVERALL WIDTH 28.5" (0.72m) OVERALLHEIGHT 39" (0.99m)
11
11
1
R
Thank You for SelectingThank You for Selecting
Thank You for SelectingThank You for Selecting
Thank You for Selecting
Operator Owner's Manual
The Powerful QUIET BLOW ®BLOWER
QB882, QB882IC, QB882H, QB882CARB, QB1102IC,
QB1102H
For Models:

Part No. 430187 Form No. F060496C
WW
WW
WARNING:ARNING:
ARNING:ARNING:
ARNING: DO NODO NO
DO NODO NO
DO NOTT
TT
T
1. DO NOTDO NOT
DO NOTDO NOT
D O N O T run engine in an enclosed area.
Exhaust gases contain carbon monoxide, an
odorless and deadly poison.
2. DO NOTDO NOT
DO NOTDO NOT
D O N O T place hands or feet near moving
or rotating parts.
3. DO NOTDO NOT
DO NOTDO NOT
D O N O T store, spill or use gasoline near
an open flame, or devices such as a stove,
furnace, or water heater which use a pilot
light or devices which can create a spark.
4. DO NOTDO NOT
DO NOTDO NOT
D O N O T refuel indoors where area is not
well ventilated. Outdoor refueling is recom-
mended.
5. DO NOTDO NOT
DO NOTDO NOT
D O N O T fill fuel tank while engine is
running. Allow engine to cool for 2 minutes
before refueling. Store fuel in approved
safety containers.
6. DO NOTDO NOT
DO NOTDO NOT
D O N O T remove fuel tank cap while
engine is running.
7. DO NOTDO NOT
DO NOTDO NOT
DO NOT operate engine when smell of
gasoline is present or other explosive
conditions exist.
8. DO NOTDO NOT
DO NOTDO NOT
D O N O T operate engine if gasoline is
spilled. Move machine away from the spill
and avoid creating any ignition until the
gasoline has evaporated.
9. DO NOTDO NOT
DO NOTDO NOT
D O N O T transport unit with fuel in tank.
10. DO NOTDO NOT
DO NOTDO NOT
D O N O T smoke when filling fuel tank.
11. DO NODO NO
DO NODO NO
DO NOTT
TT
T choke carburetor to stop engine .
Whenever possible, gradually reduce engine
speed before stopping.
12. DO NOTDO NOT
DO NOTDO NOT
D O N O T run engine at excessive speeds.
This may result in injury & /or damage
tounit.
Page 2 of 8
13. DO NOTDO NOT
DO NOTDO NOT
D O N O T tamper with governor springs,
governor links or other parts which may
change the governed engine speed.
14. DO NOTDO NOT
DO NOTDO NOT
D O N O T tamper with the engine speed
selected by the engine manufacturer.
15. DO NOTDO NOT
DO NOTDO NOT
D O N O T check for spark with spark plug
or spark plug wire removed. Use an
approved tester.
16. DO NOTDO NOT
DO NOTDO NOT
D O N O T crank engine with spark plug
removed. If engine is flooded, place throttle
in “FAST” position and crank until engine
starts.
17. DO NODO NO
DO NODO NO
D O N O T strike flywheel with a hard
object or metal tool as this may cause
flywheel to shatter in operation. Use proper
tools to service engine.
18. DO NOTDO NOT
DO NOTDO NOT
D O N O T operate engine without a
muffler. Inspect per iodically and replace,if
necessary. If engine is equipped with
m uffler deflector , inspect per iodically and
replace , if necessar y, with correct deflector.
19. DO NOTDO NOT
DO NOTDO NOT
D O N O T operate engine with an
accumulation of grass, leaves, dirt or other
combustible material in the muffler area.
20. DO NOTDO NOT
DO NOTDO NOT
D O N O T use this engine on any forest
covered, brush covered, or grass covered
unimproved land unless a spark arrester is
installed on the m uffler.The arrester must
be maintained in effective working order by
the operator. In the State of Calif or nia the
above is required by law (Section 4442 of
the California Public Resources Code).
Other states may have similar laws.
Federal laws apply on federal lands.
OPERATOR
VIBRAVIBRA
VIBRAVIBRA
VIBRATIONTION
TIONTION
TION
Vibration levels at the operators handles were
measured in the vertical, lateral, and longitudinal
directions using calibrated vibration test equipment.
Tests were perf ormed on 2/9/19962/9/1996
2/9/19962/9/1996
2/9/1996 under the
conditions listed:
WIND DIRECTION:
HUMIDITY:
TEMPERATURE:
BAROMETRIC PRESSURE:
GENERAL CONDITION:
GENERAL CONDITION:
WIND SPEED:
WIND DIRECTION:
HUMIDITY:
TEMPERATURE:
BAROMETRIC PRESSURE:
55
55
5
SAFETY INSTRUCTIONSSAFETY INSTRUCTIONS
SAFETY INSTRUCTIONSSAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
GENERAL SAFETYGENERAL SAFETY
GENERAL SAFETYGENERAL SAFETY
GENERAL SAFETY
ASSEMBLASSEMBL
ASSEMBLASSEMBL
ASSEMBL
YY
YY
Y
LABELSLABELS
LABELSLABELS
LABELS
PP
PP
PARAR
ARAR
AR
TS BTS B
TS BTS B
TS BAA
AA
AG & CONTRG & CONTR
G & CONTRG & CONTR
G & CONTROLSOLS
OLSOLS
OLS
OPERAOPERA
OPERAOPERA
OPERA
TIONTION
TIONTION
TION
PP
PP
PARAR
ARAR
AR
TS DRATS DRA
TS DRATS DRA
TS DRAWING & LISTWING & LIST
WING & LISTWING & LIST
WING & LIST
MAINTENANCEMAINTENANCE
MAINTENANCEMAINTENANCE
MAINTENANCE
TROUBLESHOOTINGTROUBLESHOOTING
TROUBLESHOOTINGTROUBLESHOOTING
TROUBLESHOOTING
WW
WW
WARRANTY PRARRANTY PR
ARRANTY PRARRANTY PR
ARRANTY PROCEDUREOCEDURE
OCEDUREOCEDURE
OCEDURE
○○○
○○○○○○
○○ ○○○○○
○○○○○○○○
○○○○○○○○
○○○○○
○○
6 - 7
8
8
8
5
4
4
3
3
2
TT
TT
TABLE OF CONTENTSABLE OF CONTENTS
ABLE OF CONTENTSABLE OF CONTENTS
ABLE OF CONTENTS
66
66
6
77
77
7
VIBRATION LEVELS 1.9g
88
88
8
SOUNDSOUND
SOUNDSOUND
SOUND
SOUND TESTS
SUNNY
IN THE INTEREST OF SAFETYIN THE INTEREST OF SAFETY
IN THE INTEREST OF SAFETYIN THE INTEREST OF SAFETY
IN THE INTEREST OF SAFETY
BEFORE STBEFORE ST
BEFORE STBEFORE ST
BEFORE STARAR
ARAR
AR
TING ENGINE,TING ENGINE,
TING ENGINE,TING ENGINE,
TING ENGINE, READ AND UNDERSTREAD AND UNDERST
READ AND UNDERSTREAD AND UNDERST
READ AND UNDERSTANDAND
ANDAND
AND THETHE
THETHE
THE “ENTIRE OPERA“ENTIRE OPERA
“ENTIRE OPERA“ENTIRE OPERA
“ENTIRE OPERATT
TT
TOR'S MANUOR'S MANU
OR'S MANUOR'S MANU
OR'S MANUAL &AL &
AL &AL &
AL &
ENGINE MANUAL.”ENGINE MANUAL.”
ENGINE MANUAL.”ENGINE MANUAL.”
ENGINE MANUAL.”
THIS SYMBOL MEANSTHIS SYMBOL MEANS
THIS SYMBOL MEANSTHIS SYMBOL MEANS
THIS SYMBOL MEANS WW
WW
WARNING OR CAARNING OR CA
ARNING OR CAARNING OR CA
ARNING OR CAUTION.UTION.
UTION.UTION.
UTION. DEADEA
DEADEA
DEATH,TH,
TH,TH,
TH, PERSONAL INJURPERSONAL INJUR
PERSONAL INJURPERSONAL INJUR
PERSONAL INJURY AND/OR PRY AND/OR PR
Y AND/OR PRY AND/OR PR
Y AND/OR PROPEROPER
OPEROPER
OPERTYTY
TYTY
TY
DD
DD
DAMAAMA
AMAAMA
AMA
GE MAGE MA
GE MAGE MA
GE MAY OCCUR UNLESS INSTRY OCCUR UNLESS INSTR
Y OCCUR UNLESS INSTRY OCCUR UNLESS INSTR
Y OCCUR UNLESS INSTRUCTIONS ARE FOLLOUCTIONS ARE FOLLO
UCTIONS ARE FOLLOUCTIONS ARE FOLLO
UCTIONS ARE FOLLOWED CAREFULLWED CAREFULL
WED CAREFULLWED CAREFULL
WED CAREFULLYY
YY
Y..
..
.
21. DO NODO NO
DO NODO NO
D O N OT touch hot muffler , cylinder ,or
fins because contact may cause burns.
22. DO NOTDO NOT
DO NOTDO NOT
D O N O T run engine without air cleaner
or air cleaner cover.
23. DO NOTDO NOT
DO NOTDO NOT
D O N O T operate during excessive
vibration!
24. DO NOTDO NOT
DO NOTDO NOT
D O N O T leave machine unattended
while in operation.
25. DO NOTDO NOT
DO NOTDO NOT
D O N O T park machine on a steep grade
or slope.
WW
WW
WARNING:ARNING:
ARNING:ARNING:
ARNING: DODO
DODO
DO
1.
ALAL
ALAL
AL
WW
WW
WAA
AA
AYS DOYS DO
YS DOYS DO
Y S D O remove the wire from the
spark plug when servicing the engine or
equipment TO PREVENT ACCIDENTAL
STA RTING.
2. DODO
DODO
D O keep cylinder fins and governor parts
free of grass and other debris which can
affect engine speed.
3. DODO
DODO
D O pull starter cord slowly until resistance
is felt. Then pull cord rapidly to avoid
kickback and prevent hand or ar m injur y.
4. DODO
DODO
D O examine muffler periodically to be
sure it is functioning eff ectiv ely. A wornor
leaking muffler should be repaired or
replaced as necessary.
5. DODO
DODO
D O use fresh gasoline. Stale fuel can
gum carburetor and cause leakage.
6. DODO
DODO
D O check fuel lines and fittings frequently
for cracks or leaks. Replace if necessary
7. FollowFollow
FollowFollow
Follow engine manufacturer operating
and maintenance instructions.
8. InspectInspect
InspectInspect
Inspect machine and work area before
starting unit.
WARNING! The engine exhaust from this product contains chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
89
96
SUNNY
WIND SPEED:
58%
30.04
W
9
47 63
18
SW
32%
29.8
Sound tests were conducted on model QB882IC
in accordance with 79/113/EEC and were
performed on
1/12/19961/12/1996
1/12/19961/12/1996
1/12/1996 under the conditions
listed:

Part No. 430187 Form No. F060496C
Page 3 of 8
For your safety and the safety of others, these directions should be followed:
Use of Ear Protection is recommended while
operating this machine.
Do not operate this machine without first reading
owner's manual and engine manufacturer's manual.
Use of Eye and breathing protection is recom-
mended when using this machine, especially in
dry and dusty conditions.
GENERAL SAFETY
99
99
9
PACKING CHECKLIST
1111
1111
11
·DO NOT place hands or feet inside air intake opening, near
exhaust outlet or near any moving parts.
·DO NOT start engine without deflector attached to exhaust
outlet.
PUT OIL IN ENGINE BEFORE STARTING
Read all safety and operating instruc-
tions before assembling or starting this
unit.
1010
1010
10 ASSEMBLY
YourBilly Goat isshipped fromthe factoryin onecarton,
completelyassembledexceptfor theupperhandle assembly,
handlebrace, plate deflectorandthrottle control.
These items should be included in your carton.
If any of these parts are missing, contact your
dealer.
BoxingChecklist
Denotes parts found in
Parts Bag Assembly
(shown on page 4).
Handle Upper
Assembly
400957
Check
Handle Brace
400951
·DO NOT direct exhaust outlet toward any bystanders.
·DO NOT operate this equipment without first inspecting
work area.
·DO NOT operate this equipment during excessive vibration.
·DO NOT start engine without housing front plate attached.
·DO NOT operate this machine on slopes greater than 20%.
·DO NOT blow any hot or burning debris, or any toxic or
explosive material.
·DO NOT allow children to operate this equipment.
1. Install upper handle (Item 28), to preassembled lower handle (item 29),
using two screws (Item 17), and two lock nuts, (Item 32). Hand tighten only.
2. Install front of handle brace (Item 30), to blower housing using one
screw (Item 17), one washer (Item 58) and one lock nut (item 32). Install
rear of handle brace (item 30) to upper handle vibration mounts using two
lock nuts (item 32). Hand tighten only.
3. Securely tighten all hardware listed above in steps 1 thru 2.
4. Attach throttle control assembly to inside of upper handle using screw
(item 15), lock nut (item 37) and clamp cables (item 20).
5.Connect spark plug wire.
Check
Check
Parts Bag &
Literature Assy
430186
Per Model
Check
Briggs & Stratton 8
HP
Per Model
Multi-Language
MS2558
Honda 8 & 11 HP
P/N31ZH9602
00X31-ZH9-6020
English
Check
Parts Bag
& Litera-
ture Assy
Engine
Manual
Per
Model
Check
Briggs & Stratton
11HP
Multi-Language
MS2558
Check
Briggs & Stratton 8
HP
IndustrialPlus
P/N270367

Part No. 430187 Form No. F060496C
Page 4 of 8
These labels should be included on your Blower. If any
of these labels are damaged, replace them before
putting this equipment into operation. Item and part
numbers are given to help in ordering replacement
labels.
4
Check
Owner's
Manual
430187
Check
Warranty
Card
400972
Check
EU Declaration
of Conformity
& EU Distribu-
tor List
430189
Literature Checklist
Owner's
Manual
Warranty
Card
EUDeclaration
of Conformity
& EU
Distributor List
Throttle
Control
CONTROLS
PARTS BAG & LITERATURE ASSY P/N 430186
PARTS BAG ASSEMBLY CHECKLIST P/N 430194
INSTRUCTION LABELS ENGINE LABELS
1212
1212
12
1515
1515
15
1313
1313
13
WHEN OIL LEVEL LOW,
ENGINE STOPS IMMEDIATELY.
OIL ALERT
Read Owner’s Manual Before Operating.
Lire le manuel d’utilisation avant la mise en route.
Vor Inbetriebnahme Bedienungs - und Wartungsanleitung lesen.
Favor leer las instrucciones de operacion antes de operar el
motor.
Consultare il Manuale Uso e Manutenzione prima dell utilizzo.
Las Skotselinstruktionen Innan Start.
'
'
'
..
..
Honda
Briggs & Stratton
HONDA MOTOR CO. , LTD. MADE IN JAPAN
READ OWNER’S MANUAL BEFORE OPERATION.
LIRE LE MANUEL D UTILISATEURAVANT USAGE.
VOR INBETRIEBNAHME UNBEDINGHT BEDIENUNGSANLEITUNG DURCHLESEN.
NO UTILIZAR SINANTES NO HABER LEIDO EL MANUAL
1414
1414
14
15 ScrewCap
1/4-20 x 1 3/4
8041009 Qty.
1
Clamp Cable 1"
900813 Qty. 3
20
LabelDo Not FillWhile
Engine Is Hot
Item 11 Part No.400268
EXPLOSIVE FUEL
STOP ENGINE AND ALLOW TO
COOL BEFORE REFUELING.
400268
WARNING
LabelDanger Keep
Hands and Feet Away
Item41 Part No.400424
DANGER
KEEP HANDS and FEET AWAY
Label Read Owner's Manual
Item No. 59 Part No. 890301
DANGER
810736
LabelDanger Flying Material
Item No. 44 Part No. 810736
890254
Label Ear Eye Breathing
Item No. 63 Part No. 890254
Literature
Parts Bag
430195
Check
Literature
Parts Bag
Stop
position
Start
position
Briggs and
HONDA
engines have
a choke type
carburetor that
is operated by
movingthe
throttle control
to the full fast
position.
STOP
START
32 Nut Lock 5/16-18
8160002 Qty. 5 37 Nut Lock 1/4-20
8160001 Qty. 1
17 ScrewCap
5/16-18 x 1 3/4
8041031 Qty. 2
17
ScrewCap
5/16-18 x 2 1/2
8041034 Qty. 1
58
Washer 5/16
FLAT CUT
8171003 Qty. 1
13
RopeGuide
830533 Qty. 2

Part No. 430187 Form No. F060496C
Page 5 of 8
Never store engine indoors or in enclosed poorly venti-
lated areas with fuel in tank, where fuel fumes may reach an
open flame, spark or pilot light, as on a furnace, water heater,
clothes dryer or other gas appliance.
If engine is to be unused for 30 days or more, prepare as
follows:
Remove all gasoline from carburetor and fuel tank to
prevent gum deposits from forming on these parts and
causing possible malfunction of engine. Drain fuel outdoors,
into an approved container, away from open flame. Be sure
engine is cool. Do not smoke. Run engine until fuel tank is
empty and engine runs out of gasoline.
NOTE: Fuel stabilizer (such as Sta-Bil) is an acceptable alternative in minimizing
the formation of fuel gum deposits during storage. Add stabilizer to gasoline in
fuel tank or storage container. Always follow mix ratio found on stabilizer
container. Run engine at least 10 min. after adding stabilizer to allow it to reach
the carburetor.
HANDLING&TRANSPORTING:
STORAGE
OPERATION
1616
1616
16
Usingtwopeople to liftmachineisrecommended. Lift holding the
handleand handle brace. Secureinplace during transport.
INTENDED USE: This machine is designed for cleaning
outdoor surfaces, where the debris can be effectively
blown into a consolidated area for convenient pickup and
removal.
BLOWINGOPERATION
16.216.2
16.216.2
16.2
Adjustdiverter rodto sidedischarge fornormal blowing or to
forward discharge for blowing along walls, fences or hard-to-
reachareas (seeright).
ENGINE: See engine manufacturer’s instructions
for type and amount of oil and gasoline used.
Engine must be level when checking and filling oil and
gasoline.
ENGINE SPEED: Controlled by throttle leveron the handle.
Under normal conditions, operate at minimum throttle to
accomplish your current cleaning task.
FUELVALVE: Move fuel valve to "ON" position (when
provided on engine).
CHOKE: Operated with choke lever on side of engine .
THROTTLE: Move remote throttle control to fast position.
Pull starting rope to start engine.
IFYOUR UNIT FAILS TO START:
See Troubleshooting on page 8.
STARTING
16.116.1
16.116.1
16.1
Inspect machine work area and machine before operat-
ing. Make sure that all operators of this equipment are
trained in general machine use and safety.
PUTOILINENGINEBEFORE STARTING
Like all mechanical tools, reasonable care must
be used when operating machine.
Do not operate if excessive vibration occurs. If excessive
vibration occurs, shut engine off immediately and check
for damaged or worn impeller, loose impeller bolt, loose
impeller key, loose engine or lodged foreign objects.
Note: See parts list for proper impeller bolt torque
specifications. (See trouble shooting section on page 8).
16.416.4
16.416.4
16.4
16.516.5
16.516.5
16.5
FrontDischarge
SideDischarge

Part No. 430187 Form No. F060496C
Page 6 of 8
R
PARTS DRAWING
1818
1818
18
QB882, QB882IC,
QB882H,QB882CARB,
QB1102IC, QB1102H

Part No. 430187 Form No. F060496C
QB882 QB882IC QB882CARB QB882H QB1102IC QB1102H
ITEM DESCRIPTION PART NO QTY PART NO QTY PART NO QTY PART NO QTY PART NO QTY PART NO QTY
1 ENGINE - 11 HP HONDA - - - - - - - - - - 400931 1
ENGINE - 11 HP BRIGGS & STRATTON IC - - - - - - - - 400466 1 - -
ENGINE - 8 HP HONDA - - - - - - 400937 1 - - - -
ENGINE - 8 HP BRIGGS & STRATTON 800136 1 - - - - - - - - - -
ENGINE - 8 HP BRIGGS & STRATTON IC - - 800880 1 - - - - - - - -
ENGINE- 8 HP BRIGGS & STRATTON INDUSTRIAL PLUS - - - - 430163 1 - - - - - -
2 LOCK CLIP 400591 1 400591 1 400591 1 400591 1 400591 1 400591 1
3
4 PLATE FRONT .A. & GRILL 430183 1 430183 1 430183 1 430183 1 430183 1 430183 1
5 IMPELLER ASSY 400965 1 400965 1 400965 1 400965 1 400965 1 400965 1
6 KEY SQUARE 1/4 X 2 1/4 *9201123 1 *9201123 1 *9201123 1 *9201123 1 *9201123 1 *9201123 1
7 DOOR DIVERTER ASSEMBLY 430170 1 430170 1 430170 1 430170 1 430170 1 430170 1
8 AXLE 430181 1 430181 1 430181 1 430181 1 430181 1 430181 1
9 ASHER LOCK 7/16 T ISTED TOOTH 850132 1 850132 1 850132 1 850132 1 850132 1 - -
ASHER LOCK 3/8 T ISTED TOOTH
)
- - - - - - - - - - 400502 1
10 SCRE CAP 7/16-20 x 1-1/4 HEX. HD GR. 5
(
TORQUE 60 FT LBS
)(
81.4N.m
)
800554 1 800554 1 800554 1 800554 1 800554 1 - -
SCRE CAP 3/8 -24 x 1-1/2 HEX. HD GR. 8
(
TORQUE 50 FT LBS
)(
68N.m
)
------ - - - -900344-
11 LABEL DO NOT FILL HEN ENGINE IS HOT 400268 1 400268 1 400268 1 400268 1 400268 1 400268 1
12 SHEET METAL SCRE 1/4 x 3/4 DRILL POINT 430208 9 430208 9 430208 9 430208 9 430208 9 430208 9
13 GUIDE ROPE 830533 2 830533 2 830533 2 830533 2 830533 2 830533 2
14 SCRE CAP 5/16-18 x 1 - 1/4 *8041029 6 *8041029 6 *8041029 6 *8041029 6 *8041029 6 *8041029 6
15 SCRE CAP 1/4 -20 x 1-3/4 *8041009 1 *8041009 1 *8041009 1 *8041009 1 *8041009 1 *8041009 1
16 NUT LOCK 3/8 -16 *8160003 1 *8160003 1 *8160003 1 *8160003 1 *8160003 1 *8160003 1
17 SCRE CAP 5/16-18 x 1¾ *8041031 2 *8041031 2 *8041031 2 *8041031 2 *8041031 2 *8041031 2
18 SPACER HEEL 400302 1 400302 1 400302 1 400302 1 400302 1 400302 1
19 ASHER 1/2 SAE 8172011 2 8172011 2 8172011 2 8172011 2 8172011 2 8172011 2
20 CLAMP CABLE PLASTIC 1 900813 3 900813 3 900813 3 900813 3 900813 3 900813 3
21 THROTTLE CONTROL ASSY
(
INCL. ITEMS 15, 37, 20
)
430207 1 430207 1 430207 1 430207 1 430207 1 430207 1
22 SCRE CAP 5/16-18 X 2½ *8041034 1 *8041034 1 *8041034 1 *8041034 1 *8041034 1 *8041034 1
23 HEEL FRONT 8" 900816 1 900816 1 900816 1 900816 1 900816 1 900816 1
24 SCRE CAP,
(
FRONT AXLE
)
3/8-16 x 3" *8041058 1 *8041058 1 *8041058 1 *8041058 1 *8041058 1 *8041058 1
25 SCRE CAP 5/16-18 x 3/4 *8041026 1 *8041026 1 *8041026 1 *8041026 1 *8041026 1 *8041026 1
26 HEEL, REAR 400295 2 400295 2 400295 2 400295 2 400295 2 400295 2
27 BRACKET
(
FRONT HEEL
)
430192 1 430192 1 430192 1 430192 1 430192 1 430192 1
28 HANDLE UPPER ASSY
(
incl. items 14
(
2
)
, 35
(
2
)
, 46, 58
(
2
)
400957 1 400957 1 400957 1 400957 1 400957 1 400957 1
29 HANDLE LO ER 400950 1 400950 1 400950 1 400950 1 400950 1 400950 1
30 HANDLE- BRACE 400951 1 400951 1 400951 1 400951 1 400951 1 400951 1
31 SCRE CAP 5/16 -18 x 1¾ *8041031 4 *8041031 4 *8041031 4 *8041031 4 *8041031 4 *8041031 4
32 NUT LOCK , 5/16-18 HEX *8160002 19 *8160002 19 *8160002 19 *8160002 19 *8160002 19 *8160002 19
33 NUT LOCK 5/16-18 THIN HT *8161041 1 *8161041 1 *8161041 1 *8161041 1 *8161041 1 *8161041 1
34 SCRE CAP 5/16 -24 NF x 1½ *8042030 2 *8042030 2 *8042030 2 *8042030 2 - - *8042030 2
SCRE CAP 5/16 -24 NF x ¾ - - - - - - - - *8042026 2 - -
35 VIBRATION MOUNT 400173 6 400173 6 400173 6 400173 6 400173 6 400173 6
36 LOOSE PARTS ASSY
(
INCL ITEMS 32
(
5
)
, 58
(
1
)
, 15
(
1
)
, 37
(
1
)
, 430185 1 430185 1 430185 1 430185 1 430185 1 430185 1
20
(
3
)
, 17
(
3
)
37 NUT LOCK 1/4 - 20 HEX *8160001 1 *8160001 1 *8160001 1 *8160001 1 *8160001 1 *8160001 1
38 RING RETAINING ¾ 850230 2 850230 2 850230 2 850230 2 850230 2 850230 2
39
40 DEFLECTOR 430193 1 430193 1 430193 1 430193 1 430193 1 430193 1
41 LABEL DANGER HANDS & FEET 400424 1 400424 1 400424 1 400424 1 400424 1 400424 1
42 BOLT CARRIAGE 5/16 -18 x 1-3/4 *8024043 1 *8024043 1 *8024043 1 *8024043 1 *8024043 1 *8024043 1
43 ASHER - FLAT 3/4 S.A.E.
(
3/16 x 1-1/2 x 1/8
)
*8172015 2 *8172015 2 *8172015 2 *8172015 2 *8172015 2 *8172015 2
44 LABEL DANGER FLYING MATERIAL 810736 1 810736 1 810736 1 810736 1 810736 1 810736 1
45
46 GRIP 400570 2 400570 2 400570 2 400570 2 400570 2 400570 2
47 KNOB 400339 1 400339 1 400339 1 400339 1 400339 1 400339 1
48 GUARD MUFFLER
(
COMES / ITEM 1
)
400010 1 400010 1 400010 1 YES - YES - 400933 1
49 ASHER 3/8 FLAT CUT 8171004 1 8171004 1 8171004 1 8171004 1 8171004 1 8171004 1
50
51
52
53
54
55 KNOB DIVERTER 430198 1 430198 1 430198 1 430198 1 430198 1 430198 1
56 FRAME ASSY
(
INCLUDES 41, 44, 63
)
430171 1 430171 1 430171 1 430171 1 430171 1 430171 1
57 SCRE CAP 5/16 - 18 X 1" *8041028 1 *8041028 1 *8041028 1 *8041028 1 *8041028 1 *8041028 1
58 ASHER FLAT CUT 5/16
(
3/8 ID x 7/8 OD x1/16
)
*8171003 11 *8171003 11 *8171003 11 *8171003 15 *8171003 11 *8171003 15
59 LABEL READ O NER'S MANUAL 890301 1 890301 1 890301 1 890301 1 890301 1 890301 1
60
61
62
63 LABEL EAR EYE BREATHING 890254 1 890254 1 890254 1 890254 1 890254 1 890254 1
64 NUT 5/16-18 *8143002 1 *8143002 1 *8143002 1 *8143002 1 *8143002 1 *8143002 1
Page 7 of 8
Denotes parts found in parts bag assembly.
*Notes standard hardware that may be purchased locally.
1919
1919
19 PARTS
LIST

Part No. 430187 Form No. F060496C
Page 8 of 8
MAINTENANCE
Clear clog.
Solution
Problem Possible Cause
TROUBLESHOOTING
Before Requesting Service Review These Suggestions
Air intake or exhaust clogged.
Abnormal vibration. Loose or out of balance impeller or loose engine. Check impeller and replace if required. Check Engine.
Poor air performance
Check stop switches, throttle, choke position and gasoline. Connect
spark plug wire.Clean or replace air cleaner.Or contact a qualified
service person.
Engine will not start. Stop switch off (Honda only). Throttle in off position. Engine not
in full choke position (Honda only). Out of gasoline. Bad or old
gasoline. Spark Plug wire disconnected. Dirty air cleaner.
Engine is locked, will not
pull over. Engine problem. Contact an engine servicing dealer for engine problems.
1717
1717
17
Use only a qualified mechanic for
any adjustments, disassembly or
any kind of repair .
DISCONNECT SPARK PLUGWIRE
BEFORESERVICING UNIT.
WARNING: TO AVOID PERSONAL INJURY, ALWAYS
TURN MACHINE OFF, MAKE SURE ALL MOVING
PARTS COME TO A COMPLETE STOP.
ENGINE: See engine manufacturer
operator's instructions.
RECONNECT SPARK PLUGWIRE AND
GUARDS BEFORESTARTINGENGINE.
1. Wait for engine to cool and disconnect spark plug.
2. Remove front wheel (item 23),and front wheel bracket
(item 27).
3. Remove housing front plate (item 4), by removing nine
(9) screws (item 12), around outside of front plate.
4. Remove impeller bolt and lock washer.
NOTE: DONOTPULLORPRYON IMPELLER BLADES.
5. Pull on center hub backplate area only of impeller. If
impeller slides off freely, proceed to (step 8).
6. Place two crowbars between center hub backplate area
of impeller and housing on opposite sides. Carefully pry
impeller away from engine until it loosens. Using a
penetrating oil can help loosen a stuck impeller.
7. If the impeller does not loosen, obtain a 1” (25.4mm)
longer bolt of the same diameter and thread type as the
impeller bolt. Thread longer bolt by hand into the crank-
shaft until bolt bottoms. Using a suitable gear or wheel
puller against the bolt head and the impeller back-plate
(near the blades), remove impeller from shaft.
8. Reinstall new impeller in reverse order of removal.
9. Tighten impeller bolt. Torque impeller bolt (see parts
list on page 7 for proper impeller bolt torque specifica-
tions).
2020
2020
20
IMPELLER REMOVAL
17.217.2
17.217.2
17.2
Engine(See Engine Manual)
Check for excessive vibration
Maintenance Schedule
Maintenance Opera-
tion
Follow these hourly maintenance intervals.
Inspect for loose parts
Inspect for worn or damaged parts
17.117.1
17.117.1
17.1
Lubricate wheels
Every
Use Every 5 hrs.
or (Daily) Every 25
hrs.
TIRE AIR PRESSURE: Check at regular intervalsand
maintain.
Rear Tires only - 30 Psi. (21 kPa).
Engine Service and Warranty
Contact your nearest engine manufacturer's
authorized servicing dealer.
22.122.1
22.122.1
22.1
Purchased
from
Purchase
Date
2121
2121
21
Serial Plate Record your machine model, serial number
and date-of-purchase and where purchased
R
min-1
Operator
1803 S. Jefferson
P.O. Box 308
Lee's Summit,
MO 64063 / USA
Tel [phone]
Fax [phone]
Model Serial No.
Unit(Weight) EnginePower
lbs. kg kW rpm
2222
2222
22 Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.
Note: To process a Warranty Claim, it is necessary to quote the Model
& Serial number who are printed on the Billy Goat Serial Plate.
BILLY GOAT INDUSTRIES INC.
P.O.BOX308 (1803 S JEFFERSON LEE'SSUMMIT,MO.64063 /USA
PHONE:[phone]FAX:[phone]
R
WARRANTY PROCEDURE
89
96