Billy Goat KV600SP User manual

Part No 891061 - 1 - Form No F052209A
KV HOSE KIT P/N 891125
BILLY GOAT KV HOSE KIT
(P/N 891125)
PURPOSE: To allow for vacuuming in hard to reach places.

Part No 891061 - 2 - Form No F052209A
KV HOSE KIT P/N 891125
INSTALLATION:
Step 1. Attach nozzle wear guards.
1. Disconnect spark plug wire.
2. Raise the nozzle height to its highest position and
secure the unit from moving.
3. Remove the two bolts, nuts and washers on the
sides of the nozzle that hold the reinforcement
bracket on the interior of the nozzle. Do not discard
the old hardware.
4. Slide the guards into place then secure the guards
with the hardware previously removed.
5. Tighten the hardware using two 7/16” wrenches.
6. Repeat steps 2 through 5 on the left hand side.
WARNING!Improper attachment of
nozzle holder can cause damage to the
hose from hot exhaust exiting the engine.
Step 2. Attach the hose nozzle bracket (item
10).
1. Remove the two screws on the muffler side of the
top plate. Left side for for Briggs and right side for
Honda (see figure at right). Attach the bracket with the
screws (item 12) provided. Do Not over tighten as this
may strip the screws.
Remove the screws from these two positions
Briggs
Honda
Remove the screws from these two positions
TKV
Remove the screws from these two positions

Part No 891061 - 3 - Form No F052209A
KV HOSE KIT P/N 891125
INSTALLATION: continued
Step 3. Attach coupler (item 8) and nozzle to
hose.
1. Slide the two hose clamps over both ends of the
hose and at one end attach the coupler to the hose
using a 5/16” nut driver. Note: the hose is attached to
the end of the coupler without the pin. Make sure the
hose is completely seated next to the plate and secure it
with one of the hose clamps. Next attach the nozzle with
the handle to the other end of the hose by sliding it into
the hose with enough distance to allow the clamp to hold
the hose to the nozzle securely then tighten the clamp.
Step 4. Attach the hose-holding bar (item 11).
1. Connect loop on right side of wire bracket hose
retainer to the upper handle of the machine, pull left side
of wire until the loop will go over the upper handle.
2. Attach the blocker plate to the wire bracket hose
retainer when not in use by sliding the wide slot over the
top of the wire bracket and then sliding it down to it’s
resting position.
Step 5. Attach hose coupler to nozzle housing.
1. Slide the hose coupler into the nozzle housing. Slide it
in at an angle and insert one of the pins into the slot,
then rotate and slide the other pin through, this will allow
the coupler to sit flush.
2. Reconnect spark plug.
Step 6. Hose placement when not in use.
1. With the hose off to the left side of the machine (on
the Honda model), drape the hose over the hose wire
bracket holder and rest the nozzle into the nozzle
bracket holder. Note: The hose should be wrapped
around the right side of the machine with Briggs models.
Use this method of transporting the hose when not in
use (See picture right). Warning: Do not let the hose
come into contact with hot parts of the engine, as this
will damage your hose and is not covered by the
warranty.
8
1
1

Part No 891061 - 4 - Form No F052209A
KV HOSE KIT P/N 891125
Operation
1. Simply slide the plate (item 10) onto the wear guards
till the front is flush with the front edge of the nozzle. To
remove simply apply pressure to the outside edges at
the wear brackets and slide forward. This will allow
suction through the hose when attached rather than the
nozzle. To remove the plate push outward on the tabs
and this will allow you to slide the plate off.
10
ITEM NO. PART
NUMBER DESCRIPTION QTY.
1 891029 NOZZLE GUARD RH 1
2 891031 NOZZLE GUARD LH 1
5 891044 HOSE 4" x 7' CLEAR PVC GREEN HELIX 1
6 800896 CLAMP HOSE 4" 2
7 800803 NOZZLE ASSY 4" 1
8 890040 HOSE COUPLER 1
9 891122 NOZZLE RETAINER BRACKET 1
10 891030 NOZZLE BLOCKING KV 1
11 890025 WIRE BRACKET HOSE RETAINER 1
12 891146 SCREWCAP 1/4-20 X 1" HWH TYPE F 2
Reference hardware
3 8041006 SCREWCAP 1/4-20 X 1" 4
4 8160001 NUT LOCK 1/4-20 4

Part No 891061 - 5 - Form No F052209A
KV HOSE KIT P/N 891125
HOSE CARE & SHIPPING INFORMATION
SHIPPING TAG
IMPORTANT NOTICE
This merchandise was in perfect condition when packed and shipped.
Unpack immediately and check for damage.
Place any damage claim with delivering carrier and have inspection made at once.
Our warranty covers manufacturing defects only.
DO NOT RETURN TO SHIPPER.
SHIPPER-WARNING
TOP LOAD ONLY TO PREVENT SHIPPING DAMAGE.
HOSE CARE
ATTENTION!
•Hoses are wear items and are only warranted against manufactures
defects. Hose must be inspected for shipping damage before using.
•Proper care is required to prevent damage. Operators should be cautious
and keep the hose as straight as possible when vacuuming to not only
help prevent clogging, but also to also help prevent abnormal wear to the
sides of the hose. Rotate hose periodically to extend life. (Suggest ¼ turn
every 20 hours.)
•Hose that has been exposed to extreme temperatures, chemicals,
abrasive material or that have been run over will not be warranted.
•The 8” (810523), 10” (810705), and the 12” (790148) hoses have internal
wrapping must be installed so the overlapping edges face in the direction
of airflow. These hoses are marked by the manufacturer with an airflow
direction arrow. Installing the hose with the airflow direction arrow
reversed will cause premature failure and VOIDS the warranty.