BILT HARD BR-JSAC1217 User manual

4 in 1 Multi – use Jump starter
OWNER’S MANUAL
BR – JSAC1217
•4 in 1 Multi- use
• 12V- 400A Cranking, 900A peak
• Super brightness work lightwith SOS
mode
• 2* 12V DC output
• 1* USB 5V output
•250PSI Air compressor
• Heavy duty clamps
• Robust shell
• ON/ OFF Switch
• Ultra safety: Reverse polarity protection
•1 Year Warranty

WARNING
This manual contains important safety
instruction, read and understand before
operation!
1. SAVE THESE INSTRUCTIONS. This manual contains
important safety and operating instructions. You may need to
refer to these instructions at a later date.
2. To reduce risk of battery explosion, follow these
instructions and those published by battery manufacturer and
manufacturer of any equipment you intend to use in vicinity of
battery. Review cautionary marking on these products and on
engine.
Work Area Safety
1. Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
2. Do not operate Power Pack in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. The Power Pack can create sparks which may
ignite the dust or fumes.
3. Keep children and bystanders away while operating the
Power Pack. Distractions can cause you to lose control.
4. Store idle equipment. Always lock up tools and keep out
of reach of children.
Electrical Safety
1. Do not drop a metal tool onto battery. It might spark or
short-circuit battery or other electrical part that may
cause explosion.
2. Do not operate if Power Pack has received a sharp blow,
been dropped, or otherwise damaged in any way; take it
to a qualified technician.
3. Do not leave Power Pack unattended while switched on.
It could result in fire and property damage.
4. Do not expose to rain or wet conditions. Water entering
the Power Pack will increase the risk of electric shock.
5. Do not use an extension cord with this item.
6. Use of an attachment not recommended or sold by the
manufacturer may result in a risk of fire, electric shock, or
injury to persons.
7. To reduce risk of damage to electric plug and cord, pull
by plug rather than cord when disconnecting the Adapter.
8. Do not operate with damaged cord or plug. Replace the
cord or plug immediately.
Personal Safety
1. Wear ANSI-approved splash-resistant safety goggles and
heavy-duty rubber work gloves whenever connecting,
disconnecting, or working near battery. Battery acid can cause
permanent blindness. Avoid touching eyes while working near
battery.
2. Do not use Power Pack while you are tired or under the
influence of drugs, alcohol or medication. A moment of
inattention while operating Power Pack may result in serious
personal injury.
3. Remove personal metal items such as rings, bracelets,
necklaces, and watches when working with a lead-acid battery.
A lead-acid battery can produce a short -circuit current high
enough to weld a ring or the like to metal, causing a severe
burn.
People with pacemakers should consult their physician(s)
before use
Power Pack Safety Warnings
1.Lead-acid batteries generate hydrogen gas when charging.
Hydrogen gas is explosive. Only use the Jump-Start system in
a well-ventilated area.
2.Jump Starting A Vehicle
a. Use the Power Pack for jump starting a LEAD-ACID battery
only.
b. For emergency use only. Do not use the Power Pack as a
replacement for a vehicle battery.
c. Be sure area around battery is well ventilated while battery is
being jump started.
d. NEVER jump start a frozen battery.
e. Do not attempt to jump start a vehicle with a
non-rechargeable or defective battery.
f. Study all battery manufacturer’s specific precautions for jump
starting.
g. DO NOT TOUCH POSITIVE AND NEGATIVE BATTERY
CLAMPS TOGETHER.
h. Unplug the Power Pack from its Adapter before
connecting its cables to a battery
i. Connect and disconnect battery cable clamps only
after setting any Jump Starter switches to OFF position.
j. Connect cables to proper polarities. Connect black
cable to negative body ground and red cable to positive
battery terminal.
k. Locate Power Pack as far away from battery as
batter
y
cables
p
ermit
1

SETUP – BEFORE USE
Read the ENTIRE IMPORTANT SAFETY INSTRUCTIONS
section at the beginning of this manual including all text
under subheadings therein before setup or use of this
product.
FUNCTION:
1. Power Switch
2. Work Light
3. LED status indicator
4.12V DC output port
5. USB output port
6. Output cable
7. Heavy duty clamp
1
2
3
4
5
6
7
1
2
3
4
1. Air compressor gauge
2. Air compressor switch
3. Air hose compartment
4. AC power input plug
CHARGING THE POWER PACK
WARNING! Always charge on a non-flammable surface.
Press and hold the Battery Test Button on the front
of the unit to check the battery power level.
a. Green light is ready for use.
b. Yellow light needs to be charged.
c. Red light should be charged immediately.
Turn the Clamp Power Switch on front of unit to the
OFF position.
Note: Before initial use, completely charge the Power
Pack.
1. Plug the 120VAC Adapter into a 2 or 3-prong
outlet.
2. Slide the Adapter socket on the 120VAC Charging
Input on the back of the Power Pack.
3. The Charging Indicator lights will illuminate in a
cycle from red, to yellow, to green while the unit is
charging. The green Charging Indicator light
will remain on after charging is complete. The
battery power level must be checked periodically
when charging, and the Power Pack must be
unplugged when it is fully charged.
NOTE:
FAILURE TO RECHARGE POWER PACK WILL
VOID WARRANTY.
Recharge:
a. When yellow light comes on while pressing the
Battery Test Button.
b. After each Jump-Start.
c. Once a month.
2

The Power Pack can run/charge 12VDC auto, RV,
marine, or other portable appliances that draw 10
amps or less.
The lower the amount of watts the appliance draws,
the longer the Power Pack can power it before needing
to be recharged.
Calculate the total wattage needed to run the
appliance before operation. You do not need to
calculate startup or surge wattages.
To calculate the size of the load you plan to use with
the Power Pack, use the following formula:
Amps x Volts = Watts
For example, if an appliance whose running amps total
7 amps, you will need 84 watts of power (7 amps x
12V = 84 Watts) to run the items. This figure is within
the capacity of the unit (10 amps x 12V = 120 Watts).
Note: Use this chart as a guideline only.
The actual power usage may vary based on the model
or brand of the appliance. Check the actual wattage of
your appliances and calculate the amount of power
needed to run/charge them.
DC APPLIANCE COMPATIBILITY
OPERATION
Jump Starting a Vehicle
1. Press the Battery Test button to verify that the
Power Pack is fully charged. Recharge as needed,
following the instructions in the “Charging the
Power Pack” section
2. Turn off the vehicle ignition switch and all
accessories (lights, radio, climate control, etc.).
3. Turn Clamp Power Switch on the Power Pack to
their OFF position. You may leave the Work Light
on if needed.
4. Connect the red Positive Battery Cable to
vehicle’s positive battery terminal. Connect the
black Negative Battery Cable to a non-moving
metal part of the vehicle.
5. When the correct connection has been made, turn
the Clamp Power Switch to the ON position.
6. WAIT FIVE MINUTES, then start the vehicle. If the
vehicle does not start, wait an additional 3 minutes
before trying again.
7. After the vehicle is started, turn the Clamp
Power Switch to the OFF position. Remove the
black Negative Battery Cable first, and then the
red Positive Battery Cable.
WARNING! THE VEHICLE WILL NOT START IF
YOU DO NOT WAIT AT LEAST 5 MINUTES.
Using the Work Light
1. To turn the Work Light on, press the Work Light
button.
2. To turn flashing lights on, press the Work Light
button again.
3. To turn the Work Light off, press the Work Light
button again.
Using the Air compressor
1. Press the Battery Test button to verify that the
Power Pack is fully charged. Recharge as needed,
following the instructions in the “Charging the
Power Pack” section on page 6.
2. Open the Air Hose Compartment on the back of
the unit and pull out the air hose.
3. Check the proper inflation level for the object that
is being inflated.
Tire Inflation
1. Position the Tire Inflator over the valve stem and
push down firmly, making sure it is fully seated.
2. Press the lever down.
3. Press the Air Compressor Switch on.
3

RUNNING/ CHARGING DC APPLIANCE
1. Press the Battery Test Button to verify that the
Power Pack is fully charged. Recharge as needed,
following the instructions in the “Charging the
Power Pack” section.
2. Make sure the total wattage of the appliance is
within the range of the Power Pack.
3. Make sure that the Clamp Power Switch and
appliance are off.
4. Plug the appliance into the 12VDC Outlet.
5. Turn on the appliance.
6. When finished using, turn off and unplug the
a
pp
liance.
RUNNING/ CHARGING USB APPLIANCE
1. Press the Battery Test button to verify that the
Power Pack is fully charged. Recharge as needed,
following the instructions in the “Charging the
Power Pack” section.
2. Plug the device into the USB Port.
3. When finished, unplug the device from the USB
Port.
MAINTANENCE & WARRANTY
TO PREVENT SERIOUS INJURY: Unplug the Power
Pack, turn the Clamp Power Switch off and allow
Power Pack to cool completely before performing any
inspection, maintenance, or cleaning procedures.
BEFORE EACH USE, inspect the general condition of
the Power Pack. Check for: loose hardware,
cracked or broken parts,
damaged electrical wiring or cable insulation, and
any other condition that may affect its safe operation.
1. Keep unit clean and clamps free of dirt, debris, or
grease
2. For longer working life, protect Power Pack from
sunlight and moisture.
3. AFTER USE, wipe external surfaces of the Power
Pack with clean cloth.
4. CONTAINS NON-SPILLABLE, SEALED LEAD-ACID
BATTERY. BATTERY MUST BE RECYCLED
Battery Replacement and Disposal
WARNING! To prevent damage or injury,
replacement battery must be identical to original.
LEAD BATTERY MUST BE RECYCLED.
Replace the Battery when the red light comes on
while pressing the Battery Test button after
recharging.
1. Remove all screws from the back of the case and
lift off the panel.
2. Lift out the Battery without damaging the circuit
board.
Note: Notice how the red and black cables connect to
the old battery and make sure to keep them in place,
connecting them to the new battery.
3. Detach the recharging wires and Battery Cables
from the battery terminals.
4. Position the replacement battery with the label
facing out, and make sure the red (+) recharging
wire and Battery Cable is attached to the positive
(+) battery terminal. Connect both of the
recharging wires and Battery Cables.
5. Carefully slide the Battery into the compartment
without damaging the circuit board.
6. Replace the back panel and the screws.
WARRANTY
The main unit of jump starter enjoys 1 Year warranty to be
free from defects in use due to materials or quality problem.
This warranty covers the cost of the defective product only
and does not cover the cost of installation. we reserves the
right to refuse credit in the event that any damage to the
product resulted from collision, improper installation, or
other customer abuses.
This policy extends only to the original purchaser of the
product and is nontransferable.
If any query or want more information, feel free to contact
our Customer Support: [phone] or send mail to:
[e-mail].
4