Next HARTFORD 860904 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if
necessary.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration
or warping.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
found to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
CARE INSTRUCTIONS
• Natural features ensure that each piece is individual. Every effort is made to ensure colour continuity between
pieces, however this is a natural product, slight colour variations and natural grain markings may occur.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Do not rub or scrub the surface when cleaning.
• For general cleaning, periodically dust with a soft cloth.
• Do not put hot dishes directly on the surfaces of the item.
PRODUCT INFORMATION
• Made from Pine with NC lacquer finish.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.
• Made in China.
• A minimum of 2 persons is required to assemble this product.
860904 HARTFORD T TLSHELE860904 HARTFORD T TLSHELE
Page 1 of 7

FITTINGS
PARTS
Page 2 of 7

STEP ONE
1. Insert 2 x wood dowels (B) to top of side rail (2)
2. Insert 2 x wood dowels (B) to top of side rail (1)
3. Insert 12 x wood dowels (B) to shelf (4), (5) & (6).
Page 3 of 7

STEP THREE
1. Attach shelf (4),(5) & (6) to side rail (1) and secured
by 8 x screws(A), tighten with a screw driver.
2. Attached side rail (2) to assembled unit and
secured by 8 x screws(A), tighten with a screw
driver.
1. Attach top panel (3) onto assembled unit
STEP TWO
1. Insert 2 x wood dowels (B) to top of side rail (2)
2. Insert 2 x wood dowels (B) to top of side rail (1)
3. Insert 12 x wood dowels (B) to shelf (4), (5) & (6).
Page 4 of 7

STEP FOUR
STEP FIVE
1. Attach top panel (3) onto assembled unit
1. Secured top panel(3) to assembled unit by 4 x
screws (A), tighten with a screw driver.
1. Attach 1 x wall attachment straps (C) to the back
of the top panel with 1 x washer (D) and 1 x screw
(E).
Page 5 of 7

STEP SIX
1. Attach 1 x wall attachment straps (C) to the back
of the top panel with 1 x washer (D) and 1 x screw
(E).
1. Move the item into position and attach the end of
the strap to the wall with the approciate screw,
washer and wall plug for your wall type.
2. WARNING: Always ensure the area to be drilled is
free from hidden electrical wires, water and gas
pipes.
3. NOTE: Wall fixings are not included, please source
suitable fixings for your wall type. If in doubt, please
consult a qualified tradesman.
Page 6 of 7

Next Retail Ltd, Desford Road, Enderby, Leicester, LE19 4AT
Page 7 of 7