Binatone 2300 User manual

USER GUIDE
Before operating this set,
please read these instructions carefully.
Concept Combo 2300
CORDED AND
DIGITAL CORDLESS
TELEPHONE
UK BTP Ver 3, Dec 07
Note:This guide is for the corded part only. For instructions on how to use
the cordless part see the "Combo 2300 Cordless Handset" user guide.

Importantnote —emergencycalls
TheCC2300 cordless handset isnot designed for
making emergencycallswhenthe mains power fails.
But,ifthere’s a powerfailure, you can use the base
unit telephone tomake an Emergency Call, by lifting
up thecorded handsetinstead of using the
speakerphone.
*** Before operating thisset, pleasereadthese
instructions carefully.
If youneed help …..
Binatone Helpline (forUKonly)
Monday toFriday from9:00am to 5:00pm
Tel: [phone]
**Please note thatallcalls are charged at localrate
Orvisit our website:
http://www.binatoneonline.com
Unpacking yourCC2300system
In the box,you willfind:
Ƶthe base unit telephone
Ƶa telephone linecablefor the baseunit
Ƶa mains power adapterfor the baseunit
Ƶthe cordless handset(uptofive, depending on
which CC2300 system you’ve bought)
Ƶtwo 1.2V 550mA rechargeable batteries and a
battery compartment cover for each handset
Ƶup to five charger pods, each with a mains power
supply for multi handset systems
Ƶtwo user guides, one for the corded phone and one
for the cordless handset.
Keep the packaging materials in a safe place in case
you later need to transport the unit.
Keep your sales (till) receipt, which is your
guarantee.
Note: After lifting the handset you will need to wait
for several seconds to get dial tone, before keying in
the telephone number to make the call.
Also you cannot dial numbers from memories when
the mains power is off.

Binatone Help Line : 0845 345 9677 1
LCD Display
Menu/Ok
Press to access menu
Pressas “OK”keyto
confirm your operation
Press to mute/
un-mute microphone
Phonebook/Back /C
Press to access phonebook
records
Press to exit present menu
R(Recall)
You mayneedthisfunction
if your phone is connected
to a PBX, or if you use BT
SOS Call
Press and hold for 2 seconds
to activate the SOS call
Speakerphone
Press to call or answer a call
by using the speakerphone.
Microphone
Forspeakerphone
and answering
Where to find it
Important:
When the instruction simply say ‘press’ a button, this means you should press it briefly then
release it.
When the instruction say ‘press and hold’ a button, this means you should keep it pressed
until the display changes or you hear a tone.
Pres
messages, memos,
stored numbers or
Call
Delete(DEL)
s to delete
er Display records.
Intercom
Press to make an intercom
Up-Down(CDS)
Press to access the
Caller display records
and scroll through them
Press to change earpiece
speakerphone volume
Press to scroll through the
lists and menu options
/P
Press to redial the
last number
Press while dialing a
number to insert a pause
Calling Features.
machine recording.
during acall
MUTE
M1,M2, M3
Press to call numbers
stored on One Touch
memory
One-touch Memory
call or to transfer a call

Binatone Help Line : 0845 345 9677 2
What's on the display?
The display of your telephone contains one line with the Time/Date
and Icons, one line of numbers and one line of text.
What do the symbols mean?
Number field: showsthe telephone
numbers
Character field: showsthe Menu,
name and status of a call
Talk x This will display when the user picks up the
handset
Ring Off x This will display when the ringer is set to
OFF
Phonebook x This will display when you are in the
phonebook menu
Voicemail x
Repeat CID x This will display when the same caller has
called more than once
New CID x This will display when there is a new CID
entry or if one is being viewed
Sequence x Indicates the sequence number of the CID
record
Hands free/speakerphone x This will display when the speakerphone is
in use
A.M. x This will display if it is A.M., in the 12 hour
clock mode
P.M. x This is display if it is P.M., in the 12 hour
clock mode
This will display when you have a new Voice
Mail message. (This is a caller id service and
is not usually available from UK network
providers.)

Binatone Help Line : 0845 345 9677 3
Contents
Page
Where to find it 1
What’s on the display? 2
x What the symbols mean? 2
Read First before Use 5
x Choosing a site for base unit and
charger pod 5
x Mains power connection 5
x If you have a broadband line 5
Installation and Set-up
x Choose a suitable site for the base unit
6
x Connect the mains power lead and the
telephone line cord into the base unit 6
x Plug the main adaptor into your wall
socket 6
x Connect the base unit to the telephone
line 6
Desk/Wall mount installation 7
Desk Mount 7
Wall Mount 7
Basic settings
x To set Dateand Time9
Making and answering calls 10
x To make call
x
Tomake acall from redial list 10
x To make a call from caller display (CID)
list10
x To answer a call 10
x
ToMute orun-mute themicrophone11
x To change the earpiece or speakerphone
volumeduring a call11
x
Emergencycallwithoutmainspower 11
Memory/Phonebookmanagement 12
x To create a contact in your phonebook
Page
x
To delete a contact in the phonebook 13
x To delete all contacts in your phonebook
14
x
To edit a contact in yourphonebook 14
x To store a last number redial in your
phonebook
x Making calls from the phonebook
x
Reviewing phonebookmemorystatus
x
Direct MemoryCall
x
To Store the telephonenumber
x
To Speed-Dial the telephonenumber
x New CID log 17
x
To review the CID li
x To delete a Caller ID record 18
st 17
x
To delete all Caller ID records 18
x To Store a Caller ID contact in
phonebook18
Ringer volume, and melody 19
x To change ringer volume 19
Using multi-handset 21
x To make intercom calls 21
x To Transfer intercom call 21
x To set up a three-way conference 22
SOS call function 25
x How SOS call functipn works 25
x How to terminate SOS call function
25
x To Set SOS number 25
6
9
10
15
16
16
16
16
16
13
x
x
Caller Display (CDS)/Caller ID (CID) 17

Binatone Help Line : 0845 345 9677 4
Advanced use ofyourPhone26
x ToTurnkey tones on/off 26
x To Set flash (Recall)time26
x To Set Dialling Mode (Tone/Pulse)27
x To Set Base todefault settings27
x To Change thePIN code28
Troubleshooting 29
Cleaning and Care 31
Declaration of Conformity31
Guarantee and Service 32
Technical Details 33
Connection and conditions for use.
You can connect your Concept Combo 2300 to a direct exchange line (DEL) - a line
connected to a local exchange, with its own phone number; to an extension on an approved
compatible PBX. Do not connect the Concept Combo 2300 as an extension to a payphone.
The ringer equivalence numbers (RENs) of all instruments (phones, fax machines, etc.)
connected to an exchange line must not add up to more than 4 - otherwise, one or more
of them may not ring and/or answer calls correctly. The Concept Combo 2300 has a
REN of 1, and most other telephones have a REN of 1 unless marked otherwise.

BinatoneHelpLine : 0845 345 9677 5
Read FirstBefore Use
Choosing a site for thebase unitandcharger pod
The base unit and charger pod(s) should be placed on a level surface, ina position where:
x
the mains adapter plugwillreach aneasily accessible230-VAC switched mains
supplysocket- never tryto lengthen the mains power cable
x
the baseunit'stelephoneline cable will reachyour telephone line socket or
extension socket
x
it is not closeto asink, bathor shower, or anywhere else where it might get wet
x itisnot close to otherelectricalequipment-fridges,washing machines,
microwaveovens,fluorescentlights, televisions etc.
x
if the basecomes intocontactwith liquids,disconnectitpromptlyand use a soft
clothtodryit; if you believe thattheliquidhas seeped into theunit, donot
reconnect the basestation. Contact the Binatonehelpline.
x
it is away fromhot, humid conditionsand strong sunlight
Mainspower connection
IMPORTANT- The CC2300 base unit mustbe used with the mains adapter supplied
withthe unit.
Using any other adapter will result in non-compliance with EN60950, and will
invalidate any approval given to this apparatus.
If you have a Broadband line
If you connect your telephone to a line with a broadband connection, you will need to
insert a micro-filter between the telephone and the telephone line; otherwise you may
get interference between the telephone and the broadband, which could cause
problems.
In a home with broadband, every telephone must have a micro-filter connected, not
just the one at the telephone point that your modem is connected to. If you need more
broadband micro-filters, contact your broadband supplier.

Binatone Help Line : 0845 345 9677 6
Installation and Set-up
1/ Choose a suitable site for the
base unit (see page 5)
2/ Connect the mains power lead
and the telephone line cord into the
base unit
Plug one end of the telephone line
cord into the jack on the back of the
base (the other end will plug into the
telephone wall socket later)
3/ Plugthe mainsadaptorintoyourwall
socket. If you have one or morecharger pods,
plugthemainsadaptors accordingly
Makesurethat the 230VAC, 50hz mains socket is switched OFF
whenyouplugthe mains adapter into the socket.
4/ Connect the base unit to the telephone line
Insert the telephone line plug into the socketthen
See the note
on page 5
See the note
on page 5
switch mains power back ON.
Make sure the mains socket is switched on —
the phone won’t work without electrical power

BinatoneHelpLine : 0845 345 9677 7
Desk/Wallmount installation
To place the CC2300 on a desk, connect
the stand to the bottom of the phone in the
slots near the rear of the base as shown below.
Desk Mount
Insert the rigid clips of the stand into the slots
on the bottom of the phone (nearer the centre
of the base ). Press down firmly until the
flexible clips clicks into place.
To remove the stand, (1) pinch the flexible
clips, (2)pull back the stand, and then (3)
slide up and forward as shown below.
To place the CC2300 on a wall, connect the
stand to the bottom of the phone in the slots
near the front of the base as shown below.
Wall Mount

Desk/Wall mounting continued...
Insert the rigid clips of the stand into the slots
on the bottom of the phone (nearer the centre
of the base). Press down firmly until the flexible
clips clicks into place.
To remove the stand, (1) pinch the flexible
clips, (2) pull back the stand, and then (3)
slide up and forward as shown below.
Mark two points on the wall that are 77 mm
apart to lay the fixing centers as shown below.
BE CAREFULto check that there are no
electrical wires hidden in the wall. Fix two screws
at the marked locations, leaving approximately
7mm between the wall and the the screw head.
Hang the telephone on the screws using the
wall mount slots. You may need to remove the
telephone from the wall and tighten the screws
so that the telephone is securely fixed and does
not wobble. Place the Handset on the cradle with
the parking hook on the cradle arranged to fit
in the parking recess under the earpiece on
the Handset.
BinatoneHelpLine : 0845 345 9677 8
77 mm