BINDTEC YL-300PM User manual

YL-300PM
1,000 Banknotes-Banding Machine
User Manual

Contents
1. For your safety
2. Product introduction and accessories
3. Part name and switch function
4. Installing and removing of band
5. How to control the temperature
6. How to control the band length
7. How to band
8. Checking before troubleshooting
9. Product specifications
Product warranty

1
For your safety
For your safety
Please carefully read this user manual before
operating the machine.
Maintenance requirements
1. Make sure AC 110/220V power is supplied. The voltage
fluctuation must be kept at a minimum.
2. High temperature, high humidity or any other
environmental conditions may render the unit not
operational due to the band being jammed around the
roller or otherwise.
3. Please clean the unit once every week. It is particularly
important to keep the roller and sensor clean.
4. The warranty is void if the unit is tampered with or
disassembled by anyone other than the designated
service personnel.
5. Touching the heater when the unit is operational or
within 10 minutes of the shutdown of the machine may
cause a burn injury.
6. Make sure the power is off after using the unit.

2
Product introduction and accessories
Model : YL-300PM
1,000 Banknotes-Banding Machine
YL-300PM
[Accessories]
* Manual --------- 1copy * Film band------1roll
* Cable ----------- 1pc * Guide ---------- 1pc
* Handle bolt----- 2pcs
* Using the 20mm film band
* No odor, no harmful substances in banding
* It is possible to band for 1,000bills.
* It is tightly banded with press.
* There is the function of the control time for
press.
* It can band the documents, cards, checks,
tickets
and so on.
*Banding 1,000banknotes(10bundles) with press very tight !
*Banding with 20mm(w) film band without smell !

3
Part name and switch function
[Part name]
[ Switch function]
Spacer
Beak
Reverse click
Toggle switch
Length control volume
Idle roller
Guide roller
Main roller
Roll fixing
(Band holder)
Band direction
Power/Re-set(red)button
Auto/Forward(yellow)butt
on
Start/Backward(green)butt
on
Assistance guide
Front door
Band door
PRESS ON OFF
BILL OLD NEW
TIME LONG SHORT
LONG press time for used bills
SHORT press time for new bills

4
Installing and removing of band
1. Open the front door. The toggle switch can change the mode between "inserting
band mode" and "banding mode". If the switch is in the upper position, it is
"inserting band mode" and the lamp of the Power/Re-set button will start blinking.
Open the band door and put band in the band holder. Make sure band will unroll in
the right direction(counterclockwise).
3. If too much of the band is rolled in or jammed around the rollers, press the
Start/Backward button and then the roller will turn the other way around to allow removal
of the band.
4. Push down the toggle switch. It will convert to banding mode and the heater be heated.
If the current temperature is far below the set value, the Start/Backward button will be lit
up. If it is a little below the set value, the Auto/Forward button will be lit up. If the
Power/Re-set button blinks, it indicates that the current temperature has reached the set
value, when pushing the Power/Re-set button will cause any leftover band will be cut off,
and new band will be put in place.
5. Adjust the band feeding control to change the length of the band fed on the unit by
turning the volume in your direction or the opposite direction to increase or decrease the
length, respectively.
6. When failed to insert the band into the machine or re-insert the band for re-
arrangement, press Power/Re-set button and hold 2seconds for the band to be cut off and
machine will re-band.
2. Close the band door and hold the end of the band,
push it through the guide roller and assistance guide
and then between the Idle roller and the main
roller. Press the Auto/Forward button, then the rollers
will turn to move the band forward. At this point,
allow the band to roll in automatically as shown in
the diagram.
Toggle switch
Front door
Band door

5
How to control the temperature
6
How to control the length
7
How to band
.
Set the dip switches to set the optimal temperature for the material
of the band and other conditions. You may open the front door to
set the applicable dip switch for the desired temperature.
[Example]
Set the switch No. 3 to set the temperature at 160℃.
CAUTION! If you make turn on two or more switches at the same time,
the temperature doesn’t set properly .
Use the length control volume to adjust the length of band.
Short
Long
[Preparations]
1. Connect the power cable to the power inlet.
(The fuse hold and power switch are integrated).
2.Turn the power switch on.
3. Feed the unit with band as explained above.
4. Push down the toggle switch than will convert
to banding mode.
5. Power button(red) is blinking and Start button
(green) is on at the same time press Power button.

CAUTION! Please surely check the band direction when install the band and push
the band roll to machine body.
[How to banding]
1. Put the switch to Bill Old or New and Press switch to On.
2. Put 1,000bills(10bundles) to be bundled inside the band ring.
(Start button will start blinking if the sensor detects the objects.)
3. Press Start button and then press bar will operate ,
and the band will be cut off at the same time.
*When PRESS is Off, the AUTO button can be used.
8
Checking before troubleshooting
Follow as below if there is operation trouble or machine cannot operate.
1) Turn on the Power switch and then check if the Start/Backward button(green) are on
and then the Power/Re-set button(red) is blinking.
2) If only Power/Re-set button(red) is blinking open the front door and then push down
the toggle switch (if toggle switch is up, it is feeding mode).
3) If there are not any objects on the machine but Start button(green) is blinking it is not
match the back case with sensor. Adjust the case with sensor position.
4) If the band is not stick, check the band direction or try to re feeding.
5) If the band cannot be cut the cutter life is expired so ask to A/S.
Start Button

9
Product specifications
Speed
1,000Bills: 7 cycles/min
Dimension of bundle
Max: 180 (W) x 160(H) mm
Power supply
AC 110/220V, 50/60Hz, 1.6A
Power consumption
150 W
Heater type
Plate
Band width
Film 20mm
Product size
420 (W) ×210 (D) ×500 (H) mm
Product weight
25 kg
NOTE! Use of the band supplied by BINDTEC CO., LTD is recommended to
maintain optimal performance of the machine.

Product warranty
BINDTEC CO., LTD warrants that we will repair and replace parts in accordance with the
following terms if any defects in the material or workmanship of the machine occurs
within 12 months from the day on which the user purchases it.
A purchase receipt or other evidence of the date of purchase must be shown in order to
receive warranty services.
Warranty terms
This warranty is valid only while and if product is used and handled in a normal and
reasonable manner in accordance with the User Manual and installation instructions.
Paid services
* Please carefully read the User Manual as you will be charged for any services requested
except for product malfunctions guaranteed under the warranty.
* The product is not covered under warranty if damage or defects have occurred due to:
- Customer misuse or unauthorized tampering or repairs;
- The replacement of parts other than those designated by BINDTEC CO., LTD; or
- An act of God or the normal service life of any expendable parts being expired.
Model
Applicable bands
Date of purchase
Serial No.
Purchased at

#1018~1019, 177 Sagimakgol-ro Jungwon-gu
Seongnam-si Gyeonggi-do S. Korea
TEL :[phone] / FAX :[phone]
E-mail:[e-mail]
http://www.bindtec.kr