Bio compression Sc-3008-dl User manual

SEQUENTIAL CIRCULATOR

Quality Medical Products Since 1983

Operating Instructions

SC-3008-DL

U.S. BASED MANUFACTURER

Table of Contents

Introduction ......................................................................................................... 3

Device Description and Operating Principle ..................................................... 3

Package Contents ................................................................................................ 3

Intended Use ........................................................................................................ 4

Contraindications ................................................................................................ 4

Important Safety Tips ........................................................................................... 4

Description of International Symbols.................................................................. 5

General Equipment Specifications ..................................................................... 6

Environmental Conditions................................................................................... 6

Front Operating Panel ........................................................................................ 7

8-Chamber Garment............................................................................................. 8

Operating Instructions ........................................................................................ 8-11

Guidelines for Treatment ..................................................................................... 10

Important Usage Information ............................................................................. 12

Maintenance and Storage ................................................................................... 12

Garment Cleaning/Disinfecting Instructions ..................................................... 12

Garment Specifications ....................................................................................... 14

Troubleshooting ................................................................................................... 15

Warranty Information ......................................................................................... 16

Repair Services Information ............................................................................... 16

Disposal of Device ............................................................................................... 16

Classification ....................................................................................................... 17

Electrical Specifications/Equipment Specifications .......................................... 17

EMC Manufacturer’s Declarations..................................................................... 17-18

INTRODUCTION

Congratulaons on the purchase of your BIO COMPRESSION SYSTEMS MODEL

SC-3008-DL Sequenal Circulator Device system and garments.

DEVICE DESCRIPTION AND OPERATING PRINCIPLE:

The Model SC-3008-DL Sequenal Circulator provides gradient pneumac

compression for the treatment of lymphedema and associated venous disorders.

Sequenal gradient compression helps to increase blood ow and move excess

lymph away from the aected area for clearance from the body. This device can

provide sequenal (distal to proximal) inaon/deaon cycles of compressed air

at prescribed pressures.

PACKAGE CONTENTS:

 1 SC-3008-DL Sequenal Circulator “pump”

 1 Power Cord

 1 Operang Instrucons

 2 Blocker Bars for use during single garment therapy

Garment(s) designed for your individual use are provided separately. Do not share

garments with others.

The durable, high quality material used in the manufacturing of these products

will ensure that you experience long-lasng and uninterrupted performance.

Should any problem occur, you can feel condent that your pump and garments

are backed by the industry’s best warranty and customer service!

For any quesons or for Technical Support please call:

Toll Free Phone 1-800-888-0908

Phone/Outside US 1-201-939-0716

Warranty repairs or adjustments will be performed in a mely manner with

minimal inconvenience to you. For this reason, it is important that you obtain a

“Return Authorizaon” (RA Number) when calling.

INTENDED USE:

The Model SC-3008-DL Sequenal Circulator is a pneumac compression device

intended for either primary or adjuncve treatment of primary or secondary

lymphedema. The device is also intended for addional or alternate treatment of

venous insuciency and chronic venous stasis ulcers associated with venous

insuciency as well as general treatment for swelling of the extremies. The

device is intended for both home and hospital use.

Federal (USA) law restricts this device to sale by or on the order of a

physician

CONTRAINDICATIONS:

Compression IS NOT recommended in the following condions:

 Infecons in the limb, including cellulis without appropriate anbioc

coverage

 The presence of lymphangiosarcoma

 Deep vein thrombosis (DVT)

 Inammatory phlebis or episodes of pulmonary embolism

 Congesve heart failure (CHF)

CAUTIONS AND PRECAUTIONS:

This device is not intended for use during SLEEP.

Pressure sengs should not be changed unless ordered by a physician.

High pressure should be set with cauon on paents with peripheral arterial

occlusive disease.

Cauon must be exercised for paents with insensive, irritated, sunburned,

bruised or broken skin, or with skin condions such as skin cancer, dermas,

eczema, or psoriasis in/around treatment sites.

If skin develops blisters, redness, welts, discoloraon or others noceable

changes, or if burning, itching or increased swelling should occur, disconnue

use and consult with a physician.

To prevent the potenal for reverse pressure and retrograde ow, do not

adjust the gradient pressures without a physician’s supervision.

Slip and fall hazard. To avoid the risk of tripping or falling, do not stand or

walk while wearing garments.

Tubing may present a STRANGULATION HAZARD or restrict blood ow if it be-

comes wrapped around a limb. Use cauon and KEEP FROM CHILDREN.

Use only the garments, tubing and accessories provided for use with this de-

vice.

Do not aempt to modify this device in any way

Symbol Explanation

Refer to Documentaon before using and servicing

CAUTION

Type B - applied part.

Electrical shock hazard. Disconnect LINE CORD before servicing; refer

servicing to qualied service personnel.

Federal (USA) law restricts this device to sale by or on the order of a

physician.

IP20 Protecon against entry of 12.5 mm solids;

Without protecon against ingress of water

Class II Protecon

Serial Number

Waste Electrical Goods Recycled

Authorized Representave in the European Community

Conforms with the Medical Device Direcve (93/42/EEC) and has been

subject to the conformity procedures laid down in the council direcve

Manufacturer

Catalog / Model Number

Keep Dry

GENERAL EQUIPMENT SPECIFICATIONS:

ENVIRONMENTAL CONDITIONS:

FOR OPERATION:

AMBIENT TEMPERATURE: +50°F - +100°F (+10°C -+37.8°C)

RELATIVE HUMIDITY: 30% - 75%

ATMOSPHERIC PRESSURE: 700hPa to 1060hPa

FOR TRANSPORT AND STORAGE:

ATMOSPHERIC PRESSURE: -20°F - + 100°F (-29°C- +37.8°C)

RELATIVE HUMIDITY: 30% - 75%

ATMOSPHERIC PRESSURE: 700hPa - 1060hPa

DIMENSIONS: 4.5” H x 11.75 W x 7.75” D

WEIGHT: 5.5 lbs

INFLATION: 54 Seconds

DEFLATION: 6 Seconds

CYCLE TIME: 6.5 Seconds / Chambers

ELECTRICAL: 120 VAC, 60 Hz, 0.5 A

APPLIED PART: TYPE B

PROTECTION AGAINST ELECTRICAL

SHOCK

CLASS II

OPERATION MODE: CONTINUOUS OPERATION

PROTECTION MODE AGAINST WATER: IP20

Figure 1, Front of Pump

FRONT OPERATING PANEL:

Key Funcon

1. POWER ON/OFF BUTTON

2. MODE BUTTON

3. INCREASE BUTTON

4. DECREASE BUTTON

5. LED DISPLAY

6. CHAMBER NUMBER LED

7. RECEPTOR PORTS FOR TUBING LATCH CONNECTORS

PORTS #5-8PORTS #1-4

Figure 2, Latch Connectors on the ends of the garment tubing

8. AUXILIARY AIR SUPPLY PORT FOR BILATERAL USE (WITH BLOCKER BARS INSTALLED)

Figure 3, Blocker Bars placed on auxiliary ports for single garment use

8 Chamber Garment:

Garments are available in the size and conguraon to ensure both an eecve

treatment and maximum comfort. Please refer to secon (2.5 Pung the garment on) in

the operang manual for instrucons on how to apply your garment.

LATCH CONNECTORS: Aach and detach the garment to the pump.

They aach to the Receptor Ports (7) on the front of the device.

A second garment can aach to the auxiliary receptor ports (8) for bilateral use.

(Keep the blocker bars installed for single garment use).

TUBING: Brings air from the pump to the garment.

GARMENT: Applied part for treatment, with eight segregated pneumac chambers.

OPERATING INSTRUCTIONS:

1. Unpacking Equipment

1.1 Open the shipping box and li the device up and out of the box.

(Please be sure to SAVE your shipping box for future transporng or shipping.

When transporng, the shipping box is equipped with a special “fold-up” handle

for easy carrying)

1.2 Remove the protecve end caps from the side of the device.

1.3 Remove the garment from the plasc bag and unroll both tubing secons. Unfold

the garment and spread it at.

2. PREPARE FOR TREATMENT

2.1 Place the device on a at and sturdy surface in close proximity to where the

paent will be resng.

2.2 Aach the power cord to the back of the pump and then plug it into a safe 120 VAC,

60 Hz outlet. A grounded outlet is not required.

2.3 Note the LATCH CONNECTORS, numbered 1—4 and 5—8, located at the end of the

tubing on your garment (See Figure 2). With one hand squeeze the LATCH CON-

NECTOR with numbers facing up and push into the Receptor Ports (7) with matching

numbers located on the front panel of the device. You should hear a click when fully

engaged.

2.4 If two garments are used, remove the Blocker Bars (see Figure 3) and aach the

LATCH CONNECTORS from the second garment to the auxiliary ports (8).

2.5 Pung the garment on

LEG GARMENTS, unzip the garment gently all the way down to the boom and stop

(zipper does not separate). Place the foot at the boom end of the garment and pull

on garments straps to help guide the garment up and onto your leg. Once garment

is in place pull up the zipper while supporng the garment to wrap around the leg.

ARM GARMENTS, slide the arm through the internal cavity of the garment.

Note: Do not wear the garments directly over skin. Always wear light clothing

underneath garments for hygienic reasons and to avoid irritaon. It is

recommended that light bandages, clean hosiery or stockinees be worn

under garments. Clothing should be free of zippers, buons or other items that

could rub and chafe the skin or damage the garment.

3. Turning Pump On

3.1 Seat yourself comfortably in a reclined posion, within easy reach of the pump. Legs

should be elevated (see photo on front page).

3.2 Powering on your device - Press the “Power On/O” (1) buon to turn your pump on

and o.

3.3 When rst turned on, the LED Display (5) will show the total hours the pump has

been used. Aer 5 seconds, the LED display shows which mode your pump is set to,

aer which the pump will start to blow air. The air pressure will be the same as the

previous treatment. Factory default pressure is 50 mmHg in the chamber #1, de-

creasing to 43 mmHg in chamber #8. To change the

pressure, see Secon 5.

3.4 As the pump starts to run through its cycle, the number that shows in the LED

Display (5) is the countdown mer. The SC-3008-DL includes a automac shuto

mer. To run the pump in connuous (unmed) mode, see Secon 6.

3.5 White operang in the Timed Shuto mode, it is possible to view the set pressure by

holding down the “Mode” buon. If you would like to toggle back to the countdown

mer, simple press the “Mode” buon again.

4. END OF TREATMENT

The pump powers down one of two ways:

1) Aer your 60 minute treatment is complete

2) You press the “Power On/O” (1) buon while the pump is running.

4.1 When your treatment is over, wait one minute before taking o the garment.

4.2 Squeeze the LATCH CONNECTOR and pull outward to remove garment from pump.

4.3 Connue to assist in the evacuaon of air from garment, working from top to

boom.

4.4 Once the garment feels loose enough, you can unzip the garment all the way to

boom and remove.

Repeat steps 4.2 through 4.4 if two garments are used!

NOTE: In case of a power failure your device will automacally shut-down. The

device does not have a baery backup and does not have mer memory. Once

your power is restored you will have to turn your device back on and

resume your treatment. A new 60 minute treatment will start. You can then end

the treatment manually by turning the power o.

GUIDELINES FOR TREATMENT

A physician is required to prescribe these sengs, but general guidelines

are listed below:

 All compression sengs should be discussed with the physician. It is ulmately his / her

responsibility to prescribe the seng and it should be wrien on the

prescripon upon referral. Every paent is unique and communicaon with the

physician is important when seng pressures.

 60mmHg works well for most paents. However, a dierent pressure might be

prescribed for your personal needs.

 Presence of broc ssue may require as much as 80mmHg in order to soen the -

broc ssue and achieve reducon. Once the ssue is so, the compression can be re-

adjusted to 60mmHg.

 Paents with a history of Congesve Heart Failure (CHF), which is controlled with medi-

caon, should never be in a at posion while pumping. They should be in a

reclined posion with elevated legs during treatment. Their treatment regimen

duraon may be divided into twice a day 30 minutes per treatment.

 Paents with a history of Deep Vein Thrombosis with or without a lter may

require less compression. These paents will generally tolerate 40mmHG. These

paents with a lter may need to divide their treatment into twice a day, 30

minutes per treatment. It is suggested that the provider obtain a Negave

Doppler study from the physician for their records.

To change the pressures in the individual garment chambers, See Secon 5.

5. TO SET THE PRESSURE OF EACH CHAMBER IN YOUR GARMENT

5.1 With the pump o, press the “Power” On/O buon.

5.2 The pump will display the hours of usage for 5 seconds. While the hour meter is being dis-

played (rst 5 seconds) Press and hold the “Up” and “Down” buon at the same me and

hold them down for 5 more seconds.

5.3 The next set of numbers will show the current pressure seng in the “LED Readout” and

the chamber associated with that pressure in the “Chamber Number LED”.

5.4 Change the pressure seng using the “Up” or “Down” buon unl you get to your desired

pressure.

5.5 Press the “Mode” buon to move to the next chamber and repeat the steps above.

5.6 Aer you have set the pressure in all 8 chambers, press the “Power On/O” buon and

your pump will start to operate.

6. PROGRAMMING YOUR PUMP TO OPERATE IN DIFFERENT MODES

The SC-3008-DL can run in a number of dierent modes, all of which are set in the following

manner:

6.1 With the Pump o, press the “Power” On/O buon.

6.2 The pump will display the hours of usage for 5 seconds. While the hour meter is being dis-

played (rst 5 seconds) Press and hold the “Mode” buon 5 more seconds.

6.3 Aer 5 seconds, you will see “1Hr.” in the “LED Readout”. This indicates that you are in the

Timed Shuto mode. In this mode, the pump will operate for a set period of me between

10 and 120 minutes, then automacally turn o. The pump comes preset to this mode and

1 hour so there is no reason to go through these steps if you wish to run your pump in the 1

Hour Mode. If you would like to adjust the amount of me for treatment in the “Timed

Mode”, simple press the up or down arrows while “1Hr” is showing to adjust the me.

Once your me seng is complete, press the “Power” On/O buon and your pump will

begin its cycle.

6.4 If you want to operate in a dierent mode, aer “1Hr.” shows press the “Mode” buon

again and you will see “COn” which indicates you are in connuous mode. In this mode,

the pump will not shut o unl you manually turn it o by pressing the “Power” On/O

buon. Once you see “COn”, if you want to proceed with this seng, press the “Power”

On/O buon and your pump will begin its cycle.

6.5 Your pump comes with a “Pre-Therapy” treatment opon. In this mode, the pump will run

for 10 minutes hing only chambers 6,7,8 over and over again. Aer 10 minutes, the pump

will automacally go into either the 1 Hour mode or the Connuous mode depending on

how you set up your pump. The SC-3008-DL comes preset with the Pre-Therapy mode

turned o. To turn it on, during the Mode setup, press the “Mode” buon again aer 6.4

and you will see “PrE” in the LED Readout. While this is displayed, press the “Up” buon to

change the number in the “Chamber Number LED” from 0 to 1. The “1” indicates that the

“Pre-Therapy” treatment has been acvated, a “0” indicates that it is o. To move from 1

to 0, simply press the “Down” arrow. Once this is set, hit the “MODE” buon again which

will return you to the 1 Hour Mode. Hit the “Power” buon to start your pump in this

mode, or the “MODE” buon again to move to the Connuous Mode. A Pre-Therapy treat-

ment can be used in either mode.

Please Note: The Pre-Therapy feature should not be turned on unl the pump has run for

at least 10 minutes on a paent. This will give the pump me to learn the proper pressure

sengs for each chamber.

7. HOUR METER

7.1 The hour meter is displayed for 5 seconds each me you turn on your pump. The num-

bers in the “LED Readout” show the 1-999 hours, the leer in the “Chamber Number LED”

indicates the following:

A. Less than 1000 hours

B.= 1000 - 2000 hours

C.= 2000 - 3000 hours

D.= 3000 - 4000 hours

E.= 4000 - 5000 hours

F.= 5000 - 6000 hours

7.2 To RESET the internal hour meter and return the pump to factory sengs, with the

pump turned o, press and hold the “Mode”, “Up” and “Down” buons all at the

same me for 5 seconds. The LED will then Light up.

7.3 Aer 5 seconds, release the three buons and press the “MODE” buon. This will

reset the internal hour meter and return the pump to the original factory sengs.

IMPORTANT USAGE INFORMATION:

This pump has a customized soware that remembers the pressure requirements of

each and every paent. It is very important to reset the pump back to the original

factory sengs prior to placing the pump on a new paent.

MAINTENANCE AND STORAGE:

EXTERIOR PUMP CASING CLEANING INSTRUCTIONS:

1. Clean the exterior case and tubing with a damp (not wet) cloth using mild soap and

water soluon once per month or as needed.

GARMENT CLEANING/DISINFECTING INSTRUCTIONS:

Disconnect garment from device.

2. Open garment to expose all sides either by separang Velcro type hook and loop or

by unzipping (depending on type of garment).

WARNING!

 Only an authorized technician may open the pump

 Before cleaning, unplug power cord from electrical outlet

WARNING!

 Do not allow liquids to enter the pump, as this can present an electrical

hazard

 Always allow the pump to dry before using

 Do not use bleach on the pump

3. Cleaning soluon should consist of 1/3 cup of laundry detergent per 1 gallon of

warm tap water. Use either a large sink or plasc tub able to hold enough solu-

on (depending on size and quanty of garments) to completely submerge the

garment leaving the latch connector bars out of the water.

4. Garment should be soaked for 30 minutes with mild agitaon every 5 to 10

minutes while keeping it below water surface.

5. Thoroughly rinse garment with warm tap water and allow to air dry.

6. Harder to remove soil on surface of garment may require addional washing by

hand with a clean towel while submerged. Avoid using any abrasive materials

such as scrubbing pads or chemicals that could cause damage to the exterior sur-

face of garment.

7. Re-Submerge garment for 30 minutes (with excepon of tubing connectors) in so-

luon consisng of 1 cup of bleach per 1 gallon of warm tap water, again agitang

garment every 5 to 10 minutes while keeping garment below water surface.

Rinse garment thoroughly with warm tap water and allow to air dry. This com-

pletes the disinfecng step.

WARNING! Never allow the Latch Connectors to be submerged into the

water. If water enters the inside of the garment, damage may occur to the

device.

WARNING! DO NOT place garment in washing machine.

WARNING! DO NOT use the tubing or valves as “handles” for carrying,

handing or storing garment.

8 CHAMBER GARMENT SPECIFICATIONS:

PRODUCT APPLICATION SIZE SIDE

G8-3035-SArm Small

G8-3035-MArm Medium

G8-3035-LArm Large

G8-3035-SH/S Arm & Shoulder Small

G8-3035-SH/M Arm & Shoulder Medium

G8-3035-SH/L Arm & Shoulder Large

GV-3010-S-RArm Elite Bio Small Right

GV-3010-S-LArm Elite Bio Small Le

GV-3010-M-RArm Elite Bio Medium Right

GV-3010-M-LArm Elite Bio Medium Le

GV-3010-L-RArm Elite Bio Large Right

GV-3010-L-LArm Elite Bio Large Le

GV-3000-S-1Vest & Arm Small Le or Right

GV-3000-M-1Vest & Arm Medium Le or Right

GV-3000-L-1Vest & Arm Large Le or Right

GV-3000-S-2Vest & Arms Small (2) Le or Right

GV-3000-M-2Vest & Arms Medium (2) Le or Right

GV-3000-L-2Vest & Arms Large (2) Le or Right

G8-3045-SFull Leg Small

G8-3045-MFull Leg Medium

G8-3045-LFull Leg Large

GW8-3045-SFull Leg Small Wide

GW8-3045-MFull Leg Medium Wide

GW8-3045-LFull Leg Large Wide

GXW8-3045 Full Leg Extra Wide

A8-3045-SFull Leg Small Adjustable

A8-3045-MFull Leg Medium Adjustable

A8-3045-LFull Leg Large Adjustable

GWA8-3045-SFull Leg Small Wide Adjustable

GWA8-3045-MFull Leg Medium Wide Adjustable

GWA8-3045-LFull Leg Large Wide Adjustable

GXWA8-3045 Full Leg Extra Wide Adjustable

GN8-3045-SFull Leg Small Narrow

GN8-3045-MFull Leg Medium Narrow

GN8-3045-LFull Leg Large Narrow

C8-3035-CArm Custom Arm

C8-3045-CFull Leg Custom Leg

GBA-3045-S-2Pants Small

GBA-3045-M-2Pants Medium

GBA-3045-L-2Pants Large

TROUBLESHOOTING

If the correcve acon does not solve the problem, then call Bio Compression Systems, Inc.,

at 1-800-888-0908. Be sure to have serial number available when calling for service.

NOTE: In addion to possessing proper tools and tesng equipment, authorized service

personnel have access to all electrical schemacs, calibraon instrumentaon and

criteria and an inventory of authorized replacement parts.

Symptom Possible Cause Correcve Acon

The device is not working.

No electricity Check the electrical wall outlet to be sure that

the pump is plugged into the outlet correctly.

Check the circuit breaker to be sure there is

power to the outlet.

Power cord Unplug the power cord and look for any

damage or defects.

One garment inates but the

second one does not.

The second garment is not

receiving air.

Check the garment hoses for adequate connec-

on to the device, kinks, punctures, twists and /

or folds.

The device is making strange

and/or loud noises.

Device is on a uneven or

unstable surface

Move to a more stable surface.

An internal problem Contact Bio Compression Systems, Inc., for

repair.

Regardless of the pressure

seng the garments are

applying a very low pressure.

Defecve Garment Check the garment for adequate connecon to

the device, leaks, kinks, punctures, twists and /

or folds.

An internal problem Contact Bio Compression Systems, Inc., for

repair.

CLASSIFICATION:

1. Class of protecon against electrical shock

CLASS II EQUIPMENT

2. The degree of protecon against electric shock

APPLIED PART—TYPE B

3. Mode

Connuous operaon with intermient loading or one hour med

4. According degree of protecon against ingress of water: IP20

(without protecon against ingress of water)

WARRANTY INFORMATION:

You can feel condent that your product is backed by the best warranty in the industry

covering any and all malfuncons (including parts and labor) resulng from component

and/or manufacturing defects.

Compression Pump = 3 years from date of purchase / invoice

Sleeves/Garments = 1 year from date of purchase / invoice

Serial Number: ____________________________________

Date Purchased: ___________________________________

Local Representave/Dealer: ________________________

Phone Number: ____________________________________

REPAIR SERVICE INFORMATION:

FOR ALL REPAIR SERVICES PLEASE CALL TECHNICAL SUPPORT AT

Toll Free 1-800-888-0908.

Phone/Outside US 1-201-939-0716

PLEASE HAVE YOUR MODEL AND SERIAL NUMBER AVAILABLE.

Note: Tampering with or dismantling this device in any way will void the warranty.

DISPOSAL OF DEVICE

Medical equipment and devices should be disposed of in proper containers that

meet Environmental Protecon Agency standards. Check with your local, regional

and naonal laws and regulaons to see what is required.

ELECTRICAL SPECIFICATIONS/EQUIPMENT CLASSIFICATION

The Model SC-3008-DL interior components are “double insulated” and do not require a

“protecve ground.” The system is equipped with an 18 gauge, 2-wire, 10. Power cord,

secured through the pump casing with a Heyco strain relief brushing as well as an addional

“hold-down” clamp for added safety.

1. Class of protecon against electrical shock: CLASS II EQUIPMENT

2. The degree of protecon against electric shock: APPLIED PART-TYPE B

3. Mode: CONTINUOUS OPERATION WITH INTERMITTENT LOADING

4. According degree of protecon against ingress of water: IP20

EMC Manufacturer’s Declaraon

Model SC-3008-DL electromagnec emissions—manufacturer’s declaraon

The model SC-3008-DL is intended for use in the electromagnec environment specied below. The customer or the user of the model SC-3008-DL should assure

that it is used in such an environment.

Emissions test Compliance Electromagnec environment— guidance

RF emissions

CISPR 11

Group 1 The model SC-3008-DL uses RF energy only for its internal funcons. Therefore, its RF emissions are

very low and are not likely to cause any interference in nearby electronic equipment.

RF emissions

CISPR 11

Class B

The model SC-3008-DL is suitable for use in all establishments, including domesc establishments and

those directly connected to the public low voltage power supply network that supplies building used

for domesc purposes.

Harmonic emissions

IEC 61000-3-2

Not applicable

Voltage uctuaons / icker

emissions

IEC 61000-3-3

Not applicable

Guidance and manufacturer’s declaraon—electromagnec immunity

The model SC-3008-DL is intended for use in the electromagnec environment specied below. The customer or the user of the model SC-3008-DL should assure

that it is used in such an environment.

Immunity test IEC 60601

test level Compliance level Electromagnec environment—guidance

Electrostac

discharge (ESD)

IEC 61000-4-2

± 2, 4, and6 kV contact

± 2, 4 and 8 kV air

± 2, 4, and6 kV contact

± 2, 4 and 8 kV air

Floors should be wood, concrete or ceramic

le. If oors are covered with synthec ma-

terial, the relave humidity should be at least

30%.

Electrostac

fast transient / burst

IEC 61000-4-4

± 2 kV for power supply lines

± 1 kV for input / output lines

± 2 kV

Not applicable

Mains power quality should be that of a

typical home use locaon.

Surge

IEC 61000-4-5

± 0.5 and 1 kV line(s) to line(s)

± 2 kV line(s) to earth

± 0.5 and 1 kV dierenal mode

Not applicable, no ground wire

Mains power quality should be that of a

typical home use locaon.

Voltage dips, short

interrupons and voltage

variaons on power supply

input lines

IEC 61000-4-11

<5 % UT (>95% dip in UT) for 0.5 cycles

40 % UT (60% dip in UT) for 6 cycles

70 % UT (30% dip in UT) for 30 cycles

<5 % UT (>95% dip in UT) for 5 s

<5 % UT (>95% dip in UT) for 0.5 cycles

40 % UT (60% dip in UT) for 6 cycles

70 % UT (30% dip in UT) for 30 cycles

<5 % UT (>95% dip in UT) for 5 s

Mains power quality should be that of a

typical home use locaon. If the user of the

model SC-3008-DL requires connued opera-

on during mains power interrupons, it is

recommended that the model SC-3008-DL be

powered from an uninterrupble power

supply or a baery.

Power frequency (50/60

Hz) magnec eld

IEC 61000-4-8

3 A/m 3 A/m The power frequency magnec elds should

be at the levels found in a typical home use

locaon.

NOTE: UT is the AC mains voltage prior to applicaon of the test level.

Guidance and manufacturer’s declaraon — electromagnec immunity

The model SC-3008-DL is intended for use in the electromagnec environment specied below. The customer or the user of the model SC-3008-DL should assure

that it is used in such an environment.

Immunity test IEC 60601 test level Compliance level Electromagnec environment—guidance

Conducted RF

IEC 61000-4-6

Radiated RF

IEC 1000-4-3

3 Vrms

15 kHz to 80 MHz

3 V/m

80 MHz to 2.5 GHz

3 Vrms

3 V/m

Portable and mobile RF communicaons equipment should be used no closer to any part of the

model SC-3008-DL, than the recommended separaon distance calculated from the equaon

applicable to the frequency of the transmier.

Recommended separaon distance

80 MHz to 800 MHz

800 MHz to 2.5 GHz

where P is the maximum output power rang of the transmier in was (W) according to the

transmier manufacturer and d is the recommended separaon distance in meters (m).

Field strengths from xed RF transmiers, as determined by an electromagnec site survey,a

should be less than the compliance level in each frequency range.b

Interference may occur in the vicinity of equipment marked with the following symbol:

Note 1: At 80 MHz and 800 MHz, the higher frequency range applies.

Note 2: These guidelines may not apply to all situaons. Electromagnec propagaons is aected by absorpon and reecons from structures, objects and peo-

ple.

a Field strengths from xed transmiers, such as base staons for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio

broadcast and TV broadcast cannot be predicted theorecally with accuracy. To assess the electromagnec environment due to xed RF

transmiers, an electromagnec site survey should be considered. if the measured eld strength in the locaon in which the model SC-3008-DL is used exceeds

the applicable RF compliance level above, the model SC-3008-DL should be observed to verify normal operaon. If abnormal performance is observed, addional

measures may be necessary, such as re-orienng or relocang the model SC-3008-DL.

b Over the frequency range 150 kHZ to 80 MHz, eld strengths should be less than 3 V/m.

Recommended separaon distances between portable and mobile RF communicaons equipment and the model SC-3008-DL

The model SC-3008-DL is intended for use in an electromagnec environment in which radiated RF disturbances are controlled. The customer of user of the model

SC-3008-DL can help prevent electromagnec interference by maintaining a minimum distance between portable and mobile RF communicaons equipment

(transmiers) and the model SC-3008-DL as recommended below, according to the maximum output power of the communicaons equipment.

Rated maximum output power of

transmier

Separaon distance according to frequency of transmier

150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2.5 GHz

0.01 0.12 0.12 0.23

0.1 0.38 0.38 0.73

11.2 1.2 2.3

10 3.8 3.8 7.3

100 12 12 23

For transmiers rated at a maximum output power not listed above, the recommended separaon distance d in meters (m) can be esmated using the

equaon applicable to the frequency of the transmier, where p is the maximum output power rang of the transmier in was (W) according to the

transmier manufacturer.

Note 1: At 80 MHz, the separaon distance for the higher frequency range applies.

Note 2: These guidelines may not apply in all situaons. Electromagnec propagaon is aected by absorpon and reecon from structures, objects and people.