Biorock ECOROCK-1500 Operation manual

PAGE 1 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
INSTALLATION & USER GUIDE
FOR THE
BIOROCK SYSTEMS:
ECOROCK-1500
ECOROCK-2000
ECOROCK-3000

PAGE 2 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
TABLE OF CONTENTS
A. INSTALLATION GUIDE .............................5
B. USER GUIDE...........................................23
C. APPENDICES ..........................................34

PAGE 3 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
Dear Customer,
Congratulations on your purchase of this BIOROCK® Domestic Sewage Treatment Plant. Your new
BIOROCK will guarantee years of trouble-free operation, peace of mind and protection for the
environment.
We highly recommend that you familiarize yourself with this guide for the installation, commissioning
and maintenance of your new BIOROCK system.
The instructions for the maintenance and visual checks of the system will ensure that you have a
reliable and long-lasting sewage treatment plant.
Please do not hesitate to contact your BIOROCK distributor for any queries or further assistance.
Thank you for choosing BIOROCK.
The installation and commissioning of your BIOROCK® system should be carried out by a BIOROCK
trained and approved installer. Your installer will be able to offer you a maintenance contract. The
BIOROCK Warranty is only valid if the required maintenance is carried out by a BIOROCK trained and
approved installer.
Should you not wish to take out a maintenance contract, make sure you have your sewage treatment
plant inspected and maintained on a regular basis by an industry trained, competent wastewater
professional.
BIOROCK S.à.r.l.
Z.A.E. Robert Steichen
5, Rue Bommel
L-4940 HAUTCHARAGE
Luxemburg
E-mail: [e-mail]
Telephone: [phone]
Distributor’s name:
Contact person:
Address:
E-mail:
Telephone:
READ CAREFULLY

A. INSTALLATION GUIDE
PAGE 4 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
A. INSTALLATION GUIDE
ECOROCK SYSTEMS

A. INSTALLATION GUIDE –TABLE OF CONTENTS
PAGE 5 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
TABLE OF CONTENTS
1.THE BIOROCK SEWAGE TREATMENT SYSTEM ....................................................... 6
1.1. General points ...............................................................................................................6
1.2. Sizing …...………………………………………………………………………………………………………….….……6
1.3. Precautions ....................................................................................................................6
1.4. Identification ..................................................................................................................7
1.5. Handling and transport ..................................................................................................7
2. OPERATING PRINCIPLES OF YOUR BIOROCK® SYSTEM .......................................... 8
2.1. Primary Tank –Operating principle................................................................................8
2.2. BIOROCK® Treatment Unit –Operating principle ..........................................................9
2.3. BIOROCK® Treatment Unit –Technical ..........................................................................9
3. INSTALLATION LAYOUTS .....................................................................................10
3.1 Installation layout n°1.: Gravity discharge (non-electric)........................................... 10
3.2 Installation layout n°2.: Pumped discharge (pump after PT) ......................................10
3.3 Installation layout n°3.: Pumped discharge (pump after BIOROCK® unit) ..................10
4. INSTALLATION OF THE TANKS ............................................................................11
4.1 Principles and constraints of installation works.......................................................... 12
4.1.1 Before installation of the complete system.................................................. 12
4.1.2 Installation of the Primary Tank .................................................................. 12
4.1.3 Installation of the BIOROCK® treatment unit .............................................. 12
4.2 Installation in dry ground conditions .......................................................................... 13
4.2.1 Installation and digging in dry ground conditions........................................ 13
4.2.2 Installation of the Tanks in dry ground conditions....................................... 14
4.2.3 Backfilling in dry ground conditions ............................................................. 14
4.3 Installation in wet ground conditions.......................................................................... 14
4.4 Installation in specific sites.......................................................................................... 16
4.4.1 Installation in difficult areas and sites ......................................................... 16
4.4.2 Installation in difficult ground conditions .................................................... 16
4.4.3 Backfilling in difficult sites............................................................................ 16
4.5 Installations under roads, courtyards or storage areas............................................... 17
4.6 Other specific cases ..................................................................................................... 17
4.6.1 Incline too steep ........................................................................................... 17
5. VENTILATION AND WATER DISTRIBUTION ..........................................................18
5.1 Ventilation of the Primary Tank................................................................................... 18
5.2 Ventilation of the BIOROCK® treatment unit .............................................................. 19
5.3 Water distribution ....................................................................................................... 19
5.4 BIOROCK® media ......................................................................................................... 20
5.5 Securing the lids........................................................................................................... 20
6. STOPPING AND RESTARTING THE SYSTEM ..........................................................21
7. CONFORMITY AND WORK COMPLETION ............................................................21
8. RECOMMENDATIONS OF USE AND MAINTENANCE ............................................21
9. COMPLIANCE WITH REGULATIONS AND STANDARDS..........................................21
10. WARRANTY ......................................................................................................22

A. INSTALLATION GUIDE 1. THE ECOROCK TREATMENT PLANTS
PAGE 6 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
1. THE BIOROCK® SEWAGE TREATMENT PLANT
1.1 GENERAL POINTS
The ECOROCK SYSTEMS from BIOROCK are compact non-electric Sewage Treatment Plants. The
treatment relies on the revolutionary BIOROCK® biological purification process. The ECOROCK
sewage treatment unit is exclusively designed for domestic waste water purification.
The BIOROCK® plant consists of a Primary Tank and a ECOROCK Bioreactor. Both parts (Primary Tank
and Bioreactor) must be ventilated.
A small pump can be installed in a pump shaft downstream of the system to lift the treated water
and discharge to a higher level if needed.
BIOROCK® recommends the installation of an effluent sampling at the outlet of the treatment unit.
The ECOROCK treatment unit can be installed (retrofitted) after a non-BIOROCK Primary Tank,
provided that this tank is properly sized, equipped with an efficient effluent filter and properly
vented.
1.2 SIZING
The ECOROCK units have a capacity of 6, 10, 15 and 30 P.E. (Person Equivalent). This manual is
for the ECOROCK-1500, 3000. The capacity of the individual ECOROCK unit can be increased if
the required final effluent quality is of a lower standard than the results, achieved during the
EN-12566-3 Performance test.
1.3 PRECAUTIONS
Important precautions for the proper use of the BIOROCK® system: Only domestic sewage should
enter the system; no rainwater is allowed.
To ensure the good working order of the BIOROCK® system, the use of automatic toilet cleaners,
electric waste-disposal systems and pumps equipped with blades are not to be used.
If there is a professional kitchen on site, a grease trap should be installed. The grease trap should be
installed before the primary tank.
Do not dispose of the following items to the BIOROCK® system:
Kitchen or motor oils, fats, wax, resin, paint, solvents, hydrocarbon-based products (petrol, crude oil
etc.), any pesticide or antibacterial product, items of a toxic nature, boiler or air-conditioning
condensate, swimming pool backwash, rainwater, drainage water or ground-water.
An effective effluent filter should be installed in the outlet of the Primary Tank, before the water
goes on to the Bioreactor.
We recommend that every ECOROCK unit should be equipped with a sampling pipe.
Special care should be taken with the aeration of the system. The aeration should be checked by the
installer with a smoke test. The smoke test should be performed under normal representative
conditions.
Each unit should be vented independently and equipped with its own ventilator (wind driven or
electrical). Limit the number of elbows used (never use 90oelbows, only use 45oelbows).
The high air outlets should be installed as close as possible to the low air inlets.
Achieving efficient ventilation is the responsibility of the installer. The installer understands the local
conditions.
The Primary Tank should de-aerated separately in accordance with the manufacturer's instructions.

A. INSTALLATION GUIDE 1. THE ECOROCK TREATMENT PLANTS
PAGE 7 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
1.4 IDENTIFICATION
Before installing please copy the serial number of each tank on to the documents to be kept by the
customer (Appendix 5 of this Guide.)
1.5 HANDLING AND TRANSPORT OF THE TANKS
Two integrated slots on the bottom of the tank enable a safe movement by fork lift.
Four lifting eyes are situated on the top corners of each tank, enabling lifting by crane or JCB.
The tanks should be handled, transported and stored with care after delivery to avoid being
damaged.
When looking at the tank facing the BIOROCK® logo, the serial number is:
-On an identification tag inside the tank, and
/or
Marked as on the drawing below
-Engraved on the area to your right at the
bottom of the rounded top.
Marked as on the drawing below
M Detail of the identification plate inside the tank:

A. INSTALLATION GUIDE 2. OPERATING PRINCIPLE OF ECOROCK-5000 UNITS
PAGE 8 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
2. Operating principle of an ECOROCK® Sewage Treatment Plant
2.1 THE PRIMARY TANK
2.1.1 Ventilation of the Primary Tank
Any Primary tank should have a proper unencumbered low level and high level vent. The low level
vent should be connected directly on the outlet side of the tank and the high level on the inlet side
and should not be positioned more than 10 m1from the tank and at a minimum height of 4 m1with
a wind driven ventilator also fitted. The water inlet should be made air tight. All ventilation should
be checked with a smoke test.
2.1.2 Performance of the Primary Tanks (PT)
If you don’t use a Primary Tank of BIOROCK, you have to make sure that the quality of the effluent
of the PT meets the BIOROCK requirements. A proper ventilation of a PT is necessary, not only to
avoid smell problems, but also to evacuate the produced gasses. A Primary Tank generates
malodorous gases like sulfur hydrogen (H2S). An evacuation of the gasses is necessary to avoid that
H2S will be transformed into harmful sulfuric acid (H2SO4). sulfuric acid will harm the biological
process and can cause degradation of the BIOROCK Media.
BIOROCK claims the following performance of a PT in front of a BIOROCK unit:
Composition of normal domestic wastewater (according to EN12566-3+A2 Annex B.3.2):
Variation
BOD5*1: 150 - 500 mg O2/l
COD*1: 300 –1000 mg/l
S.S.: 200 - 700 mg/l
KN: 25 - 100 mg/l
NH4-N: 22 - 80 mg/l
P-Total: 5 - 20 mg/l
*1: The ration between BOD5and COD should always be < 2
Minimum performance requirements of a Primary Tank*2:
Effluent PT Average
EN 12566-6: 2008
BOD5: 100 - 350 mg O2/l 200 ± 50 mg O2/l
COD: 200 - 600 mg/l
S.S.: 40 - 150 mg/l 80 ± 20 mg/l
KN: 35 - 100 mg/l
NH4-N: 30 - 80 mg/l
P-Total: 4 - 20 mg/l
*2: The sampling should be done with a minimum 24 hour sampling
The effluent is easy biodegradable if the ratio of BOD5and COD is less than 2. Between 2 and 3 it is
partially biodegradable and greater than 3, the effluent is not biodegradable.

A. INSTALLATION GUIDE 2. OPERATING PRINCIPLE OF ECOROCK-5000 UNITS
PAGE 9 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
2.2 THE BIOROCK TREATMENT UNIT (Bioreactor) –ECOROCK
The ECOROCK sewage treatment units are biological purification systems, using the BIOROCK®
media as a carrier material for bacteria. An ECOROCK unit consists of two biological filtration
stages and one aeration stage, has pre-treated water passed through it by gravity. The pre-
treated water is spread over the surface of the first layer of BIOROCK® media by a distribution
system and penetrates into the media for purification.
The treated water discharging from the unit must flow by gravity to the next stage or a discharge
point.
2.3 ECOROCK TREATMENT UNIT –TECHNICAL
The tanks and covers are made of polyethylene
Each tank has two lifting eyes that are situated at the middle of the tank
The water inlet has a ø of 110 mm
Air inlet and air outlet have a ø of 110 mm
The water outlet has two possible diameters; ø75 and ø 110 mm
Each unit has a serial number that is located on the right side of the tank (A/Chapter 1.3)
All materials in the BIOROCK® plants are resistant to corrosion and guarantee a long-term
lifespan
The tanks are made by rotational molding in HDPE (High Density Polyethylene)
The tanks are UV resistant and have a lifespan of at least 25 years
The HDPE tanks are 100% recyclable
The screws are made of stainless steel
The pipes are made of PVC and Polypropylene
The entire system is nearly 100% recyclable

A. INSTALLATION GUIDE > 3. INSTALLATION LAYOUTS
PAGE 10 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
3. Installation layouts
The installation of the BIOROCK® system depends on the available site, gradient, type of ground, the
level of the water inlet and the discharge options.
When the outlet for final effluent is not accessible, a sampling shaft should be installed.
When using a final effluent pump the pump shaft can be used as a sampling shaft.
3.1 INSTALLATION LAYOUT N°1
GRAVITY DISCHARGE (non-electric)
3.2 INSTALLATION LAYOUT N°2
PUMPED DISCHARGE, PUMP AFTER THE PRIMARY TANK
3.3 INSTALLATION LAYOUT N°3
PUMPED DISCHARGE, PUMP AFTER THE ECOROCK® TREATMENT UNIT
PRIMARY TANK ECOROCK
TREATMENT UNIT
OPTIONAL
SAMPLING PIPE DISCHARGE
PRIMARY
TANK
INTERMEDIATE
PUMPING WELL
ECOROCK
TREATMENT
UNIT
OPTIONAL
SAMPLING
PIPE
DISCHARGE
PRIMARY TANK ECOROCK
TREATMENT UNIT
PUMPING &
SAMPLING PIPE DISCHARGE

A. INSTALLATION GUIDE 4. INSTALLATION OF THE TANKS
PAGE 11 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
4. INSTALLATION OF THE TANKS
This chapter provides a guide to the installation and commissioning of the BIOROCK® system. This
manual cannot be a substitute for documentation and instructions from manufacturers of non-
BIOROCK® products integrated into the system by the user.
Please take photographs of each stage of the installation with particular
attention to all of the connecting pipework
DO NOT completely fill the tanks with water before unit is backfilled
DO NOT use dirty or contaminated water
DO NOT use a mechanical compactor, only compact manually
DO NOT reuse the excavated soil or spoil from the site
DO NOT install the system too close to the house or other buildings
DO NOT install the system too close to large trees
4.1 INSTALLATION PRINCIPLE
Dimensions and weight of the ECOROCK treatment units:
ECOROCK-1500
Value
Measure
Capacity in Person Equivalent (PE)*1
6
PE
Volume of the ECOROCK-5000 unit
1.500
Litres
Length of the Tank
1.150
mm
Width of the Tank
1.150
mm
Height of the Tank
2.175
mm
Height difference water inlet –water outlet
1.098
mm
Total weight (empty) of the ECOROCK-5000 unit
186
Kg
Pipe diameters
110
mm
Cover (round)
Ø 700
mm

A. INSTALLATION GUIDE 4. INSTALLATION OF THE TANKS
PAGE 12 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
*1 The capacity of the ECOROCK units can be decreased or increased if the required effluent
quality is of a higher or lower standard than the results, achieved during the EN-12566-3
Performance test.
4.1.1 Before the installation of the complete system
Always keep the system accessible
Check the tanks and the associated equipment (internal reinforcements, connections, seals, etc.)
before installation, see technical details for each tank
A minimum distance of about 3 m1from the house and 3 m1from trees which have extensive
roots should be ensured
A minimum distance of 2.5 m1from any building should be ensured, otherwise the stability of
the building should be checked
The installation should be located away from any traffic areas and parking (at least 2 m1)
The installation of the BIOROCK® system is possible in high ground water conditions if special
Precautions are taken
Consult a professional engineer if the units are to be installed with extension sets
System lids should not be buried and should always remain accessible for maintenance
The minimum distance between the primary tank and the treatment unit is 300 mm
The distance between the side of the excavation and the tanks must be minimum of 300 mm
Connections for the BIOROCK® system are made with flexible seals with a diameter of 110 mm
Local rules and legislation should be respected
4.1.2 Installation of the Primary Tank
The Primary Tank must be installed as close as possible (less than 10 m1) to the wastewater
discharge point of the property; this avoids fats clogging in the inlet pipe. With a longer pipe run
from the property to the primary tank the installation of a grease trap may be necessary
This 110 mm diameter pipe (100 mm minimum, 160 mm maximum) should have a minimum
gradient of 2 % and a maximum of 4%
ECOROCK-2000
Value
Measure
Capacity in Person Equivalent (PE)*1
10
PE
Volume of the ECOROCK-2000 unit
2.000
Litres
Length of the Tank
1.450
mm
Width of the Tank
1.150
mm
Height of the Tank
2.075
mm
Height difference water inlet –water outlet
1.098
mm
Total weight (empty) of the ECOROCK-2000 unit
241
Kg
Pipe diameters
110
mm
Cover (round)
Ø 700
mm
ECOROCK-3000
Value
Measure
Capacity in Person Equivalent (PE)*1
15
PE
Volume of the ECOROCK-3000 unit
3000
Litres
Length of the Tank
2.150
mm
Width of the Tank
1.150
mm
Height of the Tank
2.075
mm
Height difference water inlet –water outlet
1.098
mm
Total weight (empty) of the ECOROCK-3000 unit
304
Kg
Pipe diameters
110
mm
Cover (oval)
Ø 700-1.250
mm

A. INSTALLATION GUIDE 4. INSTALLATION OF THE TANKS
PAGE 13 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
The Primary Tank should always discharge by gravity into the BIOROCK® system
Install the Primary Tank allowing a gradient towards the BIOROCK® system
The Primary Tank should be installed away from any traffic area, unless special precautions are in
place
The Primary Tank must be equipped with an efficient Effluent Filter
Installation of a Pump Well
If the effluent can’t be discharged by gravity, install a pump well & pump. The pump is
required to lift the effluent (purified water) to a higher level.
BIOROCK® has developed an optional PE pump well with a diameter of 400 mm.
The PE pump well has the same height as the ECOROCK unit.
All the connections are matching with the openings at the ECOROCK units.
At the end of the BIOROCK® Reactor the purified waste water (effluent) is collected in the
pump shaft and can be easily pumped to a higher level with a normal submersible pump.
The seals on the BIOROCK® tanks are flexible and have a diameter of 110 mm
The discharge pipe for the treated effluent should have a minimum gradient of 1%
4.1.3 Installation of the BIOROCK® treatment unit
The BIOROCK® unit must be installed downstream of the Primary Tank
The effluent from the Primary Tank should flow by gravity to the BIOROCK® unit
The gradient of the treated effluent pipe to the BIOROCK® unit should be a minimum of 1%
4.2 INSTALLATION IN DRY GROUND CONDITIONS
See Appendix «Installation in dry ground conditions»
Conditions for installation:
-Dry and stable ground conditions
-Absence of water at the bottom of the excavation
4.2.1 Installation and digging in dry ground conditions
The maximum level of top soil above the backfill is 200 mm
The units must stand on a clean and stable base such as concrete
In dry ground conditions pea gravel can be used
Mud and other soft materials must be removed from the bottom of the excavation prior to
installation
A stable base must be created at the bottom of the excavation
The base of the excavation should be level and compacted
There must be a distance of at least 300 mm between the walls of the excavation and the
units

A. INSTALLATION GUIDE 4. INSTALLATION OF THE TANKS
PAGE 14 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
4.2.2 Installation of the tanks in dry ground conditions
Once the base of the excavation is stable, the installation can begin
The Primary Tank should not be positioned horizontally; it must have a slight gradient
towards the water outlet
Before connecting any water or ventilation pipes, ensure that the units are perfectly
installed
Ensure that all levels are correct so that the wastewater can flow freely through the system
Check that all connections are correctly positioned
Ensure that the seals are watertight
4.2.3 Backfilling in dry ground conditions
Backfill the hole with 3 to 6 mm smooth pea gravel, or lean-mix concrete whilst filling the
tanks with water at the same level
Do not exceed 300 mm per filling and compaction cycle
Make sure that the BIOROCK® media is completely saturated with water
Do not backfill with the soil removed during the excavation: roots and stones can damage
the tank.
Do not compact the backfill material mechanically: compact manually.
Backfilling around and filling both the Primary Tank and BIOROCK® unit with water should
take place at the same time.
Once the backfilling is finished and compacted, check the levels of the tanks again
The lids or access covers of the system should be installed just above ground, level to
provide easy access for maintenance.
Close and secure all covers with screws
Complete the backfilling once all pipework has been checked and connected.
4.3 INSTALLATION IN HIGH GROUND WATER CONDITIONS
Appendix «Installation in high ground water conditions»
The ECOROCK units can be installed in high ground water conditions with special precautions.
If you don’t use a BIOROCK® Primary Tank, please confirm with the other manufacturer that
this Primary tank is suitable for high ground water conditions.
If you don’t use a BIOROCK® Primary Tank, please consult the manufacturer to
ensure this Primary Tank is suitable for high ground water conditions.
The level of the water table must never exceed the level of liquid inside the Primary
Tank. Extremely high water tables signify a flood risk which could cause water ingress
or collapsed tanks.

A. INSTALLATION GUIDE 4. INSTALLATION OF THE TANKS
PAGE 15 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
Perform the same work as in dry ground conditions with the additional recommendations and
modifications below:
For installations in a high water table area, ensure the adequate drainage of the excavation during
installation
Anchor the unit to the concrete slab (slab thickness should be a minimum 150 mm)
The base must extend to a minimum distance of 300 mm beyond the base of the tanks on all sides
If you are unsure, a qualified civil engineer should be consulted
Anchoring the tanks to the base is achieved with a system using the anchoring points; these
are positioned on the lower corners of the tanks
For installations in a high water table area, ensure the adequate drainage of the
excavation during installation and anchor the unit to the concrete slab
Important:
The tanks should be secured and anchored to the concrete base
In all high ground water conditions, the backfilling should be carried out to a level of 20 cm below
the tank covers.
We recommend that the tanks are backfilled with (lean mix) concrete instead of a regular backfill

A. INSTALLATION GUIDE 4. INSTALLATION OF THE TANKS
PAGE 16 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
4.4 INSTALLATION IN «DIFFICULT» AREAS AND SITES
Conditions of installation:
Difficult ground conditions can be unstable ground, clay, rocks, etc.
If necessary, ensure the adequate drainage of the excavation during installation and anchor the
unit to the concrete slab.
Solutions such as sheet piling should be used to secure the sides of the excavation.
A retaining wall may be necessary to ensure that the backfill does not move in a difficult
installation.
4.4.1 Installation in difficult areas and sites
Never use heavy clay soil for the top soil level. If the top soil to be used is predominantly clay then
mix it with sand.
In all difficult grounds conditions the base of the excavation should be constructed from
concrete with a minimum depth of 300 mm.
Roots and stones can result in damage to the tank wall and should be removed.
The depth to the bottom of the excavation and the concrete base for the Primary Tank must allow
an incline of 2% minimum for the wastewater inlet pipe from the property to the Primary Tank.
4.4.2 Installation in difficult ground conditions
Once the base of the excavation is stable the installation can begin.
Before connecting any pipe work or ventilation pipes ensure the units are perfectly installed and
stable on the excavation base. Ensuring that all levels are correct is crucial if the wastewater is to
flow efficiently through the system.
Pay special attention to the rubber seals. The seals ensure that the system is watertight.
4.4.3 Backfilling in difficult ground conditions
In all difficult ground conditions backfilling should be carried out to a level of 20 cm below the
tank covers. Concrete should be used, compacted and applied in layers of 300 mm.
A retaining wall may be necessary to ensure that the backfill does not move in a difficult
installation. The thickness and structure of any retaining wall should be specified by a qualified
engineer along with the method of construction and backfilling procedure.
At the same time as backfilling around the Primary Tank and BIOROCK® unit both tanks should be
gradually filled with clear water (increments of 300 mm)
Once the backfilling is finished and compacted, check the levels of the tanks again
The various lids or access covers for the system are installed just above ground level to provide
easy access for maintenance.
Position the hatches and secure them with the screws positioned on the sides.
Backfilling to the surface is completed once all pipe work has been connected. With a maximum
depth of 20 cm the backfill should consist of top soil without any stones or sharp objects. When
building up the final level of backfill around the covers keep in mind any future settlement of the
soil.

A. INSTALLATION GUIDE 4. INSTALLATION OF THE TANKS
PAGE 17 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
4.5 INSTALLATION UNDER ROADS, COURTYARDS OR STORAGE AREAS
Installation conditions:
Roads, courtyards or storage areas: The installation will be carried out in accordance with the
preceding paragraphs, taking into account the nature of the soil.
For an installation under roads, courtyards or storage areas, a distribution slab of
reinforced concrete should be constructed and placed above the tanks
The concrete slab must be constructed in such a way that it does not rest on the tanks
The edges of the slab must rest on the surrounding ground; the ground must be stable. If unstable
ground, specific foundations should be built
These foundations, the thickness of the slab distribution, the access to the lids of the tanks, the
unit and sampling pipe, the reinforcement and the structure of the slab, etc., will be specified by a
qualified civil engineer, based on expected traffic loads and the nature of the soil
The high air outlet pipes should preferably be installed outside the concrete slab area, if this is
impossible then they should be anchored in the slab.
4.6 OTHER SPECIFIC CASES
4.6.1 Incline too steep (>5%)
A retaining wall may be necessary to ensure that the backfill does not move if the incline is too steep.
The thickness and structure of any retaining wall should be specified by a qualified engineer along
with the method of construction and backfilling procedure.
Generally, the backfill material must be compacted pea gravel or lean mix concrete applied in layers
of 30 cm. (depending on ground conditions)
If you are not sure about the installation, always consult a local engineer

A. INSTALLATION GUIDE 5. VENTILATION AND WATER DISTRIBUTION
PAGE 18 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
5. VENTILATION & WATER DISTRIBUTION
Never smoke in the vicinity of the installation or sewage works in general.
Never enter the tanks without taking the necessary safety precautions such as
ventilation, air monitoring, air supply and other procedures as required.
Always have someone else on site if entering confined spaces.
Both Primary Tank & ECOROCK unit must be vented
The ventilation may be combined, provided that the distance between the air
inlet and the air outlet are not too far apart and that the conditions allow it.
The installer is always responsible for a proper ventilation of the Primary Tank &
the ECOROCK Treatment Unit
Make sure that the ventilation works properly
Always check the efficiency of the ventilation in both the primary tank and the
treatment units with a smoke test
If the site is not suitable for non-electric ventilation, electric ventilation should be
installed
Use as few bends as possible
NEVER USE 90obends
Only use 45obends
5.1 VENTILATION OF THE PRIMARY TANK
A Primary Tank generates malodorous gases that must be removed by effective ventilation.
The Primary Tank must have a ventilation system consisting of a low air inlet and a high air outlet.
The distance between the air inlet and air outlet pipe should be as far as possible from each other.
The high air outlet pipe should have a wind driven or electrical ventilator
The wind driven ventilator must be located at least 400 mm above roof level, clear of all
potential obstacles and located at least 1 m away from any windows or skylights
We recommend a gradient of 1% to avoid any water settling in the air pipe

A. INSTALLATION GUIDE 5. VENTILATION AND WATER DISTRIBUTION
PAGE 19 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
Only use 45obends (never use 90obends)
The ventilation pipes must have a minimum diameter of 100 mm
The Primary Tank vent pipe must be independent of the properties soil vent pipe
The water inlet pipe of the Primary Tank should be plugged or capped (blocked for air)
Always check the ventilation with a smoke test in representative conditions
(calm weather and storms are not representative conditions)
5.2 VENTILATION OF THE BIOROCK® TREATMENT UNIT
The BIOROCK treatment unit has a separate ventilation system
The vent pipe for the BIOROCK unit must be independent of the properties soil vent pipe and
must not be combined with the Primary Tank vent pipe.
The aeration of the both the upper level and the middle section of the treatment unit is combined
The air intake is located at the front of the treatment unit
The air outlet pipe should always be equipped with a wind driven or electrical ventilator
The ventilation pipes must have a minimum diameter of 100 mm
Only use 45obends (never use 90obends)
Always check the ventilation with a smoke test in representative conditions
(calm weather and storms are not representative conditions)
If the ventilation is not working properly:
Check the ventilation system again by following the diagram
Check if the pipe work is obstructed or disconnected at any stage
Check if the air outlet pipe is positioned high enough
Check that the wind driven ventilator has enough capacity, otherwise change to an electric
Ventilator
5.3 WATER DISTRIBUTION PIPE
Make sure the BIOROCK® Media is saturated with clean water
Check and adjust the water distribution pipe to ensure an even distribution across the
BIOROCK® media
Adjust the height/level of the water distribution pipes using the threaded supports
The discharge angle can also be adjusted by twisting the pipes
Make sure that the BIOROCK® media is completely saturated with water
DO NOT completely fill the tanks with water before unit is backfilled
DO NOT use dirty or contaminated water
Check the connection from the Primary Tank outlet pipe to the BIOROCK® treatment unit
There should not be any accumulation of water within the BIOROCK® unit
Water should not accumulate on top of the BIOROCK® media
The level of the BIOROCK® media must be just under the water distribution pipe
Check that the water from the Primary Tank flows by gravity into the BIOROCK® unit

A. INSTALLATION GUIDE 5. VENTILATION AND WATER DISTRIBUTION
PAGE 20 / 51 Installation and User guide –ECOROCK - Systems –26-05-2016
5.4 BIOROCK® MEDIA
BIOROCK® Media is a carrier material for bacteria. The BIOROCK® Media is clearly visible in the
tank and the bags overlap each other. Under the water distribution pipe, the BIOROCK® Media
will have a grey/black colour.
Don’t touch the BIOROCK® Media and don’t clean the BIOROCK® if it’s not necessary. The top
layer of the BIOROCK® Media may be rinsed if blocked or contaminated with solids. In this case
we recommend taking out the upper bags, rinsing them (if possible) and placing them back.
For your safety always contact BIOROCK® or your BIOROCK® dealer for
replacement or re-arrangement of BIOROCK® media bags.
Used BIOROCK® media can be returned to your dealer or to BIOROCK® S.à.r.l. in
Luxemburg for recycling
5.5 SECURING THE LIDS
The lids of the BIOROCK® tanks should remain accessible for maintenance
Always close and secure the lids after use using a screw driver.
Always close and secure the lids
Always keep the lids accessible
Make sure the lids are air tight
The lids are for pedestrian use only