Biospace InBody230 Manual

1. Turn on the InBody230 and keep the power on until the home screen
initializes. It will take 15 seconds. During the warming, do not touch
the base.
2. Step on the foot plate and measure weight.
3. Enter your personal information and press “ENTER” button.
Installation Measurement
1. Raise the stand and lift the head and lower the arms.
2. Push the knob shown above and turn it toward right to tighten the joint screw.
3. Plug the power adapter cable into the InBody230.
4. If the air bubble is not in the center of the level indicator, tighten or loosen
the leveling screws(4EA) on the foot plate to adjust the level of InBody230.
InBody230 must be leveled properly for accurate weight measurement.
BODY COMPOSITION ANALYZER
Install Manual
1. If you use the InBody230 on a carpet, static electricity may cause serious damage to the
electronic components. If the InBody230 is to be installed on a carpet, use antistatic mats
below the InBody230. Use InBody tissue to wipe feet and hands before the measurement
starts.
2. Do not wipe the base and hand electrode with cleaning liquids. If cleaning liquids enter
into InBody230, it may cause corrosion or electric shock by short circuit. For cleaning of
the InBody230, please use InBody tissue, which also has antibacterial functionality.
3.Do not dismantle InBody230. Internal parts are not for customer use and may cause
electric shock. If InBody230 is dismantled, the warranty is void, and service costs will be
charged.
DANGER
NOTECAUTION
Please keep the packaging for future events of repacking InBody230 and sending
it for servicing or otherwise transporting InBody230 elsewhere.
Head
Stand
Base
Hand Electrode
Input Buttons
Foot Electrode
Contents of the Box
Basic
InBody230
Install Manual 1EA
User’s Manual CD 1EA
Warranty
Adapter 1EA (12V, 3.5A)
Power Cable 1EA
Optional
Thermal printer
SD400 Set
Result Sheet
Carrying Bag
InBody Tissue
<Side view of InBody230>
< Leveled state >
Level Indicator
Leveling Screws
*Make sure the power
cord is rmly plugged in .
<Rear view of InBody230>
<Rear view of InBody230>
Power switch
<Printer Cable / Option>
A
B
C
A
BC
DELETE
ABC
QZ DEF
GHI JK
PRS TUV
230매뉴얼_eng_E.indd 1 2011-03-24 오후 5:31:58

Proper Posture FAQs
Cautions before Measurement
4. Grab the hand electrode and hold your arms slightly away
from the torso.
Proper posture is essential to achieve reliable results and high reproducibility.
Do not talk or move during the InBody test.
Q1. I do not know how to congure the settings.
A. Use the left right buttons (◀,▶) or number to select a category among
Region, Printer, Result, Other and Interface. Then the selected item’s
sub-categories are displayed on the screen.
Q2. Can I use my printer?
A. There is a list of compatible printers.
Please contact Biospace or the local distributor.
Q3. I do not know why error messages are shown on the LCD.
A. The InBody230 displays an error message to alert the operator of
problems and to recommend the correct action.
Turn the InBody230 off and on again
after removing the objects from the
foot plate.
If entered subject data are beyond
acceptable ranges, this error message
appears.
A subject should wipe his/her soles and
palms with wet tissue and try again.
Q4. Where can I buy printer paper and other optional devices?
A. Please contact Biospace or the local distributor.
Q5. How do I know the measurement taken is correct?
A. After taking the measurement, check the impedance at the bottom of the
results sheet printed. The impedance value must decrease in the
arrow direction.
Q6. How do I clean hand/foot electrode?
A. For cleaning of hand/foot electrode, please use InBody tissue, which
also has antibacterial functionality.
Do not use this equipment in combination with the following electronic medical devices.
- Medical devices, such as a pacemaker.
- Electronic life support systems, such as an articial heart/lung.
- Portable electronic medical devices, such as an electrocardiograph.
Measurements may not be possible due to callouses on the palm or sole.
In this case, wipe the palm and sole with an InBody Tissue before measuring.
For any problems with InBody230 or for any clinical information, contact:
Biospace Co., Ltd. [Head ofce]
518-10 Dogok 2- dong, Gangnam-gu, Seoul 135-854 KOREA
TEL : [phone] FAX : [phone]
Homepage : http://www.e-inbody.com E-mail : [e-mail]
For more information on the functions of InBody230 and descriptions on the thermal results sheet items,
see the user’s manual CD included.
For purpose of improvement, specications and design are subject to change without notice.
Gently grip the hand
electrodes so that all the
four ngers of each hand
are touching the surface
of the either hand
electrode. Touch the
circular electrode with
the thumb.
If the examinee’s
thighs are in contact
with each other, have
the examinee wear a
pair of knee-length
shorts so that the
thighs are not in contact
each other.
Step on the foot plate with bare feet,
ensuring that both heels are touching
the smaller foot electrode on either side
as illustrated.
Do not wear socks
during measurement.
Armpits are not closed up.
Straight both arms.
5. Remain still during measurement and the test takes about 30 seconds.
DANGER
NOTECAUTION
If you are using a printer, a result sheet will be printed automatically.
<Option>
ⓒ
1996 ~ Biospace Co., Ltd. All rights reserved. BM-ENG-40-E-110131
230매뉴얼_eng_E.indd 2 2011-03-24 오후 5:32:00