Biostar B760MX-E D4 User manual

FCC Informaon and Copyright
This equipment has been tested and found to comply with the limits of a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecon
against harmful interference in a residenal installaon. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instrucons,
may cause harmful interference to radio communicaons. There is no guarantee that interference
will not occur in a parcular installaon.
The vendor makes no representaons or warranes with respect to the contents here and
specially disclaims any implied warranes of merchantability or tness for any purpose. Further
the vendor reserves the right to revise this publicaon and to make changes to the contents here
without obligaon to nofy any party beforehand.
Duplicaon of this publicaon, in part or in whole, is not allowed without rst obtaining the
vendor’s approval in wring.
The content of this user’s manual is subject to be changed without noce and we will not be
responsible for any mistakes found in this user’s manual. All the brand and product names are
trademarks of their respecve companies.
Dichiarazione di conformità sintetica
Ai sensi dell’art. 2 comma 3 del D.M. 275
del 30/10/2002
Si dichiara che questo prodotto è
conforme alle normative vigenti e
soddisfa i requisiti essenziali richiesti
dalle direttive
2004/108/CE, 2006/95/CE e 1999/05/CE
quando ad esso applicabili
Short Declaration of conformity
We declare this product is complying
with the laws in force and meeting all
the essential requirements as specied
by the directives
2004/108/CE, 2006/95/CE and 1999/05/
CE
whenever these laws may be applied
The terms HDMI and HDMI High-Denion Mulmedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.

2 | Table Of Contents
Table Of Contents
FCC Informaon and Copyright ������������������������������������������������������������������������������� 1
Chapter 1: Introducon������������������������������������������������������������������������������������������� 3
1.1 Before You Start.................................................................................................................. 3
1.2 Package Checklist................................................................................................................ 3
1.3 Specicaons...................................................................................................................... 4
1.4 Rear Panel Connectors........................................................................................................ 5
B760.......................................................................................................................................... 6
1.5 Motherboard Layout .......................................................................................................... 6
B760.......................................................................................................................................... 7
Chapter 2: Hardware installaon����������������������������������������������������������������������������� 8
2.1 Install Central Processing Unit (CPU) .................................................................................. 8
2.2 Install a Heatsink............................................................................................................... 10
2.3 Connect Cooling Fans ....................................................................................................... 11
2.4 Install System Memory ..................................................................................................... 11
2.5 Expansion Slots ................................................................................................................. 13
2.6 Jumper & Switch Seng................................................................................................... 15
2.7 Headers & Connectors...................................................................................................... 16
2.8 LEDs .................................................................................................................................. 20
Chapter 3: UEFI BIOS & Soware��������������������������������������������������������������������������� 21
3.1 UEFI BIOS Setup................................................................................................................ 21
3.2 BIOS Update...................................................................................................................... 21
3.3 Soware............................................................................................................................ 25
Chapter 4: Useful help������������������������������������������������������������������������������������������� 26
4.1 Driver Installaon ............................................................................................................. 26
4.2 AMI BIOS Beep Code......................................................................................................... 27
4.3 Troubleshoong................................................................................................................ 27
APPENDIX I: Specicaons in Other Languages ����������������������������������������������������� 28
Arabic...................................................................................................................................... 28
German................................................................................................................................... 29
Spanish ................................................................................................................................... 30
Thai ........................................................................................................................................ 31
Japan....................................................................................................................................... 32

Chapter 1: Introducon | 3
B760MX-E D4｜B760MH D4｜B760MX2-E D4
Chapter 1: Introducon
1�1 Before You Start
Thank you for choosing our product. Before you start installing the motherboard, please make
sure you follow the instrucons below:
• Prepare a dry and stable working environment with sucient lighng.
• Always disconnect the computer from power outlet before operaon.
• Before you take the motherboard out from an-stac bag, ground yourself properly
by touching any safely grounded appliance, or use grounded wrist strap to remove the
stac charge.
• Avoid touching the components on motherboard or the rear side of the board unless
necessary. Hold the board on the edge, do not try to bend or ex the board.
• Do not leave any unfastened small parts inside the case aer installaon. Loose parts
will cause short circuits which may damage the equipment.
• Keep the computer from dangerous area, such as heat source, humid air and water.
• The operang temperatures of the computer should be 0 to 45 degrees Celsius.
• To avoid injury, be careful of:
Sharp pins on headers and connectors
Rough edges and sharp corners on the chassis
Damage to wires that could cause a short circuit
1.2 Package Checklist
• Serial ATA Cable x2
• Rear I/O Panel for ATX Case x1
• WIFI antenna accessories x1
• Quick Installaon Guide x1
• Fully Setup Driver DVD x1
• M.2 Anchor x1
Note
»
»The package contents may be dierent due to the sales region or models in which it was sold. For
more informaon about the standard package in your region, please contact your dealer or sales
representave.

4 | Chapter 1: Introducon
1�3 Specifications
Specicaons
CPU Support
Support for 12th/13th Generaon Intel® Core™ i9/ i7/ i5/ i3 processors and Intel® Penum® processors/
Intel® Celeron® processors in the LGA1700 package
* Please refer to www.biostar.com.tw for CPU support list.
Chipset Intel® B760
Memory
Supports Dual Channel DDR4 1866/ 2133/ 2400/ 2666/ 2933/ 3200/ 3600(OC)/ 3800(OC)/ 4000(OC)/ +4400(OC)
2x DDR4 DIMM Memory Slot, Max. Supports up to 64 GB Memory
Each DIMM supports non-ECC 4/8/16/32GB DDR4 module
Support Intel® Extreme Memory Prole (XMP) memory modules
* Please refer to www.biostar.com.tw for Memory support list.
Storage
-- Total supports 1x M.2 socket and 4x SATA III (6Gb/s) ports
4x SATA III Connector (6Gb/s)
1x M.2 (M Key) Socket (M2_PCIEG3_32G_ SATA):
Supports M.2 Type 2240 /2260 /2280 SSD module
Supports PCI-E 3.0 x4 (32Gb/s) / PCI-E 4.0 x4 (64Gb/s) - NVMe/ AHCI SSD & SATA SSD
LAN
B760MX-E D4 / B760MH D4
Intel i219v
10/ 100/ 1000 Mb/s auto negoaon, Half / Full duplex
capability
B760MX2-E D4
RTL8125B
10/ 100/ 1000/ 2500 Mb/s auto negoaon, Half / Full
duplex capability
Audio Codec ALC897
7.1 Channels, High Denion Audio
USB 4x USB 3.2 (Gen1) port (2 on rear I/Os and 2 via internal headers)
8x USB 2.0 port (4 on rear I/Os and 4 via internal headers)
Expansion Slots 1x PCIe 3.0 x1 Slot
1x PCIe 4.0 x16 Slot
Rear I/Os
B760MX-E D4 / B760MX2-E D4
1x WIFI Antenna Port
1x PS/2 Keyboard/ Mouse Port
1x HDMI
1x VGA+DVI Port
2x USB 3.2 (Gen1) port
4x USB 2.0 port
1x LAN port
3x Audio Jack
B760MH D4
1x PS/2 Keyboard/ Mouse Port
1x HDMI
1x VGA Port
2x USB 3.2 (Gen1) port
4x USB 2.0 port
1x LAN port
3x Audio Jack
Internal I/Os
B760MX-E D4 / B760MX2-E D4
4x SATA III Connector (6Gb/s)
1x M.2 (E Key) Socket : Supports 2230 type Wi-Fi &
Bluetooth module and Intel® CNVi
2x USB 2.0 Header (each header supports 2 USB 2.0
ports)
1x USB 3.2 (Gen1) Header (each header supports 2 USB
3.2 (Gen1) ports)
1x 8-Pin Power Connector
1x 24-Pin Power Connector
1x CPU Fan Connector
1x System Fan Connector
1x Front Panel Header
1x Front Audio Header
1x Internal Stereo Speaker Header
1x Clear CMOS Header
1x COM Port Header
1x TPM Header
* M.2 (E key) Wi-Fi card is not provided
B760MH D4
4x SATA III Connector (6Gb/s)
2x USB 2.0 Header (each header supports 2 USB 2.0
ports)
1x USB 3.2 (Gen1) Header (each header supports 2 USB
3.2 (Gen1) ports)
1x 8-Pin Power Connector
1x 24-Pin Power Connector
1x CPU Fan Connector
1x System Fan Connector
1x Front Panel Header
1x Front Audio Header
1x Internal Stereo Speaker Header
1x Clear CMOS Header
1x COM Port Header
1x TPM Header
Form Factor uATX Form Factor, 208 mm x 236 mm
OS Support Windows 10(64bit) / Windows 11(64bit)
* Biostar reserves the right to add or remove support for any OS with or without noce.

Chapter 1: Introducon | 5
B760MX-E D4｜B760MH D4｜B760MX2-E D4
1.4 Rear Panel Connectors
B760MX-E D4
B760MX2-E D4
B760MH D4
Note
»
»VGA/ HDMI/ DVI-D ports only work with an Intel® integrated Graphics Processor.
»
»Maximum resoluon
HDMI: 4096 x 2160 @24Hz
VGA: 4096 x 2304 @60Hz
DVI-D: 1920 x 1200 @60Hz
»
»The mainboard supports three onboard display outputs at same me and the display output
conguraon can be selected in Intel graphics driver ulity.
»
»When using the front HD audio jack and plug in the headset / microphone , the rear sound will be
automacally Disabled.
»
»The WiFi antenna port allows you to connect to the E KEY module and use the WiFi & Bluetooth
funcon.

6 | Chapter 1: Introducon
1.5 Motherboard Layout
B760MX-E D4 / B760MX2-E D4
B760
Note
»
» represents the 1st pin.

Chapter 1: Introducon | 7
B760MX-E D4｜B760MH D4｜B760MX2-E D4
B760MH D4
B760
Note
»
» represents the 1st pin.

8 | Chapter 2: Hardware installaon
Chapter 2: Hardware installaon
2.1 Install Central Processing Unit (CPU)
Step 1: Locate the CPU socket on the motherboard
Note
»
»Remove pin cap before installaon, and make good preservaon for future use. When the CPU is
removed, cover the pin cap on the empty socket to ensure pin legs won’t be damaged.
»
»The motherboard might equip with two dierent types of pin cap. Please refer below instrucon to
remove the pin cap.
Step 2: Open ILM Lever and then load plate using nger tab.
Step 3: Align and seat processor package on socket.

Chapter 2: Hardware installaon | 9
B760MX-E D4｜B760MH D4｜B760MX2-E D4
Step 4: Close the load plate.
Step 5: Remove and save cover.
Step 6: Close ILM Lever and latch
Note
»
»Ensure that you install the correct CPU designed for LGA1700 socket.
»
»The CPU ts only in one correct orientaon. Do not force the CPU into the socket to prevent
damaging the CPU.

10 | Chapter 2: Hardware installaon
2.2 Install a Heatsink
Step 1: Place the CPU fan assembly on top of the installed CPU and make sure that the four
fasteners match the motherboard holes. Orient the assembly and make the fan cable is closest
to the CPU fan connector.
Step 2: Press down two fasteners at one me in a diagonal sequence to secure the CPU fan
assembly in place. As each fastener locks into posion a click should be heard.
Note
»
»Apply the thermal interface material on the CPU before heatsink installaon, if necessary.
»
»Do not forget to connect the CPU fan connector.
»
»For proper installaon, please kindly refer to the installaon manual of your CPU heatsink.

Chapter 2: Hardware installaon | 11
B760MX-E D4｜B760MH D4｜B760MX2-E D4
2.3 Connect Cooling Fans
These fan headers support cooling-fans built in the computer. The fan cable and connector
may be dierent according to the fan manufacturer.
CPU_FAN: CPU Fan Header
Pin Assignment
1 Ground
2+12V
3FAN RPM rate sense
4 AI Fan Control
SYS_FAN1: System Fan Header
Pin Assignment
1 Ground
2+12V
3FAN RPM rate sense
4 AI Fan Control
Note
»
»CPU_FAN, SYS_FAN1 support 4-pin and 3-pin head connectors. When connecng with wires onto
connectors, please note that the red wire is the posive and should be connected to pin#2, and the
black wire is Ground and should be connected to pin#1(GND).
2.4 Install System Memory
DDR4 Modules

12 | Chapter 2: Hardware installaon
Step 1: Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot
such that the notch on the DIMM matches the break on the slot.
Step 2: Insert the DIMM vercally and rmly into the slot unl the retaining clips snap back in
place and the DIMM is properly seated.
Note
»
»If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.
Memory Capacity
DIMM Socket Locaon DDR4 Module Total Memory Size
DDR4_A 4GB/8GB/16GB/32GB Max is 64GB.
DDR4_B 4GB/8GB/16GB/32GB
Dual Channel Memory Installaon
Please refer to the following requirements to acvate Dual Channel funcon:
Install memory module of the same density in pairs, shown in the table.
Dual Channel Status DDR4_A DDR4_B
Disabled O X
Disabled X O
Enabled O O
(O means memory installed, X means memory not installed.)
Note
»
»When installing more than one memory module, we recommend to use the same brand and
capacity memory on this motherboard.

Chapter 2: Hardware installaon | 13
B760MX-E D4｜B760MH D4｜B760MX2-E D4
2.5 Expansion Slots
PCIEG4X16: PCI-Express Gen4 x16 Slots (x16 mode)
• PCI-Express 4.0 compliant.
• The maximum bandwidth of the PCIe slot is 64GB/s.
PCIEG3X1: PCI-Express Gen3 x1 Slots
• PCI-Express 3.0 compliant.
• Data transfer bandwidth up to 1GB/s per direcon; 2GB/s in total.
M2_PCIEG3_32G_SATA: M.2 (M Key) Socket
• The M.2 slot supports M.2 Type 2240/ 2260/ 2280 SSD module. When installing M.2 SSD
module, please place the screw and hex pillar to correct posion.
• Supports M.2 SATA III (6Gb/s) module and M.2 PCI Express module up to Gen3 x4
(32Gb/s) - NVMe & AHCI SSD/ SATA SSD.
HYBRID_WIFI6: M.2 (E Key) Socket (M.2 (E key) Wi-Fi card is not provided)
• Support M.2 socket 2230 type module.
• Supports WiFi/ Bluetooth module and Intel® CNVi (Integrated WiFi/ BT).
Note
»
»When using SATA SSD module on M.2 slot (M2_PCIEG3_32G_SATA), the SATA_4 connector will be
disabled.

14 | Chapter 2: Hardware installaon
Install M.2 Anchor
1. Lock the M.2 Anchor into the motherboard hole which you use for type of M.2 SSD.
2. Insert the M.2 SSD into the M.2 socket.
3. Insert the pin on the M.2 Anchor into the hole on itself.
Install an Expansion Card
You can install your expansion card by following steps:
• Read the related expansion card’s instrucon document before install the expansion
card into the computer.
• Remove your computer’s chassis cover, screws and slot bracket from the computer.
• Place a card in the expansion slot and press down on the card unl it is completely
seated in the slot.
• Secure the card’s metal bracket to the chassis back panel with a screw. (This step is only
for installing a VGA card.).
• Replace your computer’s chassis cover.
• Power on the computer, if necessary, change BIOS sengs for the expansion card.
• Install related driver for the expansion card.
Note
»
»Please be note that you will need to use M.2 type screwdriver if you want to install or uninstall the
screw. It is recommended not to use a screwdriver that does not meet the specicaons, otherwise
the screw may be damaged.

Chapter 2: Hardware installaon | 15
B760MX-E D4｜B760MH D4｜B760MX2-E D4
2.6 Jumper & Switch Setting
The illustraon shows how to set up jumpers. When the jumper cap is placed on pins, the
jumper is “close”, if not, that means the jumper is “open”.
Pin opened Pin closed Pin 1-2 closed
JCMOS1: Clear CMOS Jumper
The jumper allows users to restore the BIOS safe seng and the CMOS data. Please carefully
follow the procedures to avoid damaging the motherboard.
Pin 1-2 Open:
Normal Operaon (Default)
Pin 1-2 Short:
Clear CMOS data
Clear CMOS Procedures:
1. Remove AC power line.
2. Set the jumper to “Pin 1-2 short”, you can use a metal object like a screwdriver to touch
the two pins.
3. Wait for ve seconds.
4. Aer clearing the CMOS values, be sure the jumper is “Pin 1-2 open”.
5. Power on the AC.
6. Load Opmal Defaults and save sengs in CMOS.

16 | Chapter 2: Hardware installaon
2.7 Headers & Connectors
ATX: ATX Power Source Connector
For beer compability, we recommend to use a standard ATX 24-pin power supply for this
connector. Make sure to nd the correct orientaon before plugging the connector.
Pin Assignment Pin Assignment
13 +3.3V 1+3.3V
14 -12V 2+3.3V
15 Ground 3 Ground
16 PS_ON 4+5V
17 Ground 5 Ground
18 Ground 6 +5V
19 Ground 7 Ground
20 NC 8PW_OK
21 +5V 9Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V
ATX_12V_2X4: ATX Power Source Connector
The connector provides +12V to the CPU power circuit. If the CPU power plug is 4-pin, please
plug it into Pin 1-2-5-6 of ATX_12V_2X4.
Pin Assignment
1+12V
2+12V
3+12V
4+12V
5 Ground
6 Ground
7 Ground
8 Ground
Note
»
»Before you power on the system, please make sure that both ATX, ATX_12V_2X4 and connectors
have been plugged-in.
»
»Insucient power supplied to the system may result in instability or the peripherals not funconing
properly. Use of a PSU with a higher power output is recommended when conguring a system with
more power-consuming devices.

Chapter 2: Hardware installaon | 17
B760MX-E D4｜B760MH D4｜B760MX2-E D4
F_PANEL: Front Panel Header
This 10-pin header includes Power-on, Reset, HDD LED, Power LED connecon.
Pin Assignment Funcon Pin Assignment Funcon
1HDD LED(+) HDD
LED
2Power LED (+) Power
LED
3HDD LED(-) 4Power LED (-)
5 Ground Reset
Buon
6Power Buon Power-On
Buon
7 Reset Control 8 Ground
9NC NC 10 NA NA
SPKR: Chassis Speaker Header
Please connect the chassis speaker to this header.
Pin Assignment
1+5V
2N/A
3N/A
4Speaker
TPM_SPI: Trusted Plaorm Module Header
This header allows you to store cryptographic keys that protect informaon.
Pin Assignment Pin Assignment
1VCCSPI 2S_SPI_TPM_IRQ#
3S_PLTRST# 4S_SPI_TPM_CS2#
5NC 6F_BIOS_WP#_R
7+3V_SPI 8GND
9F_SPI_CS0#_R 10 T_SPI_CLK
11 T_SPI_MISO 12 T_SPI_MOSI
13 F_SPI_HOLD#_R 14 N/A

18 | Chapter 2: Hardware installaon
SATA_1/ SATA_2/ SATA_3/ SATA_4: Serial ATA 6.0 Gb/s Connectors
These connectors connect to SATA hard disk drives via SATA cables.
Pin Assignment
1 Ground
2TX+
3TX-
4 Ground
5RX-
6RX+
7 Ground
Note
»
»When using SATA SSD module on M.2 slot (M2_PCIEG3_32G_SATA), the SATA_4 connector will be
disabled.
F_USB32_A-5G: Header for USB 3.2 (Gen1) Ports at Front Panel
This header allows user to add addional USB ports on the PC front panel, and also can be
connected with a wide range of external peripherals.
Pin Assignment Pin Assignment
1VBUS0 11 D2+
2SSRX1- 12 D2-
3SSRX1+ 13 Ground
4 Ground 14 SSTX2+
5SSTX1- 15 SSTX2-
6SSTX1+ 16 Ground
7 Ground 17 SSRX2+
8 D1- 18 SSRX2-
9D1+ 19 VBUS1
10 ID 20 Key
F_USB20_1/ F_USB20_2: Header for USB 2.0 Ports at Front Panel
This header allows user to add addional USB ports on the PC front panel, and also can be
connected with a wide range of external peripherals.
Pin Assignment
1+5V (fused)
2+5V (fused)
3USB-
4USB-
5USB+
6USB+
7 Ground
8 Ground
9Key
10 NC

Chapter 2: Hardware installaon | 19
B760MX-E D4｜B760MH D4｜B760MX2-E D4
F_AUDIO: Front Panel Audio Header
This header allows user to connect the chassis-mount front panel audio I/O which supports HD
and AC’97 audio standards.
HD Audio AC’97
Pin Assignment Pin Assignment
1Mic Le in 1 Mic In
2 Ground 2 Ground
3 Mic Right in 3 Mic Power
4 GPIO 4 Audio Power
5 Right line in 5 RT Line Out
6Jack Sense 6RT Line Out
7Front Sense 7 Reserved
8Key 8Key
9Le line in 9LFT Line Out
10 Jack Sense 10 LFT Line Out
Note
»
»When using the front HD audio jack and plug in the headset, the rear sound will be automacally Disabled.
»
»It is recommended that you connect a high-denion front panel audio module to this connector to
avail of the motherboard’s high denion audio capability.
»
»Please try to disable the “Front Panel Jack Detecon” if you want to use an AC’97 front audio output
cable. The funcon can be found via O.S. Audio Ulity.
COM1: Serial Port Header
The motherboard has a serial port header for connecng RS-232 Port.
Pin Assignment
1 Carrier detect
2 Received data
3Transmied data
4 Data terminal ready
5Signal ground
6 Data set ready
7 Request to send
8 Clear to send
9 Ring indicator
10 Key

20 | Chapter 2: Hardware installaon
2.8 LEDs
Debug LED: Debug LED Indicators
This LEDs indicate the status of the motherboard.
BOOT - indicates boong device is not detected
or fail.
VGA - indicates GPU is not detected or fail.
DRAM - indicates DRAM is not detected or fail.
CPU - indicates CPU is not detected or fail.
Note
»
»Aer starng the computer, the LED indicators will light up in the following order:
CPU → DRAM → VGA → BOOT
»
»When the computer is ready, the LED indicator will show where the error occurred and will stay on
unl the problem is solved.
»
»Aer the computer is started, the Debug LED will not light up if there is no abnormality detected.