Biostar M7VIG Pro D User manual

M
M
M7
7
7V
V
VI
I
IG
G
G
P
P
Pr
r
ro
o
o-
-
-D
D
D
i
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. There is no guarantee that interference will not occur in
a particular installation.
The vendor makes no representations or warranties with respect to the
contents here of and specially disclaims any implied warranties of
merchantability or fitness for any purpose. Further the vendor reserves
the right to revise this publication and to make changes to the contents
here of without obligation to notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without
first obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice
and we will not be responsible for any mistakes found in this user’s
manual. All the brand and product names are trademarks of their
respective companies.

C
C
Co
o
on
n
nt
t
te
e
en
n
nt
t
t
ii
LAYOUT OF M7VIG PRO-D ..................................................................1
COMPONENT INDEX.............................................................................2
ENGLISH...................................................................................................3
M7VIG Pro-D Features............................................................................................... 3
Package contents......................................................................................................4
How to setup Jumper................................................................................................ 4
CPU Installation.........................................................................................................5
DDR DIMM Modules: DDR1/ DDR2...........................................................................6
Jumpers, Headers, Connectors & Slots...................................................................6
DEUTSCH................................................................................................13
Spezifikationen von M7VIG Pro-D..........................................................................13
Verpackungsinhalt................................................................................................... 14
Einstellung der Jumper........................................................................................... 14
Installation der CPU................................................................................................. 15
DDR-DIMM-Modules: DDR1/ DDR2......................................................................... 16
Jumpers, Headers, Anschlüsse & Slots ................................................................ 16
WARPSPEEDER.....................................................................................23
Introduction.............................................................................................................. 23
System Requirement............................................................................................... 23
Installation................................................................................................................ 24
Usage........................................................................................................................ 25
STUDIOFUN!TM......................................................................................33
Introduction.............................................................................................................. 33
Hardware Requirements.......................................................................................... 33
Installation Procedure............................................................................................. 33
Booting to StudioFun!............................................................................................. 35
Media control ........................................................................................................... 36
Control Panel ........................................................................................................... 37
Software Details....................................................................................................... 39
Select Region........................................................................................................... 41
Screensaver ............................................................................................................. 42
Display Settings....................................................................................................... 43
File Manager............................................................................................................. 44
TROUBLE SHOOTING...........................................................................1
PROBLEMLÖSUNG................................................................................2

1
Layout of M7VIG Pro-D
!NOTE: "represents the first pin.

2
Component Index
A. Power Source Selection for M. Communication Network Riser Slot
Keyboard and Mouse (JKBV1) (CNR1)
B. Power Source Selection for USB N. CNR Codec/ Onboard Selection
(JUSBV2) (JCODECSEL)
C. Back Panel Connector O. Floppy Disk Connector (FDD1)
D. ATX Power Connector (JATXPWER1) P. Wake On LAN Header (JWOL1)
E. Game Port Header (JGAME1) Q. System FAN Header (JSFAN1)
(optional) R. Front Panel Connector (JPANEL1)
F. Power Source Selection for USB S. Clear CMOS Function (JCMOS1)
(JUSBV1) T. Power Source Selection for USB
G. Case Open Connector (JCI1) (JUSBV3)
H. CD-ROM Audio-In Header (JCDIN1) U. Front USB Header (JUSB3)
I. Accelerated Graphics Port Slot (AGP1) V. IDE Connectors (IDE1-2)
J. PCI BUS Slots (PCI1-3) W. Frequency Selection (JCLK1)
K. Digital Audio Connector (JSPDIF1) X. DDR DIMM Modules (DDR1-2)
L. Front Audio Header (JF_AUDIO) Y. CPU Fan Connector (JCFAN1)

3
English
M7VIG Pro-D Features
A. Hardware
CPU
Provides Socket A.
Supports single AMD® for Athlon™ (Thunderbird™)/ Athlon™ XP/ Duron™
processors.
Front Side Bus at 200/266 MHz.
Chipset
North Bridge: VIA KM266 (VT8375).
South Bridge: VIA VT8235.
Main Memory
Supports up to 2 DDR devices.
Supports 200/266 MHz (without ECC) DDR SDRAM devices.
Maximum memory size of 2GB.
Super I/O
Chip: Winbond W83697HF.
Slots
Three 32-bits PCI bus master slots.
One AGP 1x/ 2x/ 4x slot.
On Board IDE
Supports four IDE disk drives.
Supports PIO Mode 4, Master Mode and Ultra DMA 33/66/100/133 Bus Master
Mode.
On Board AC’97 Sound Codec
Chip: VIA VT1612A.
Compliant with AC’97 specification.
Supports 2 channels.
On Board Peripherals
a.Rearside
1 serial port.
1 VGA port.
1 parallel port. (SPP/EPP/ECP mode)
1 Audio port in vertical position.
1 LAN jack.
PS/2 mouse and PS/2 keyboard.
4 USB2.0 ports.
b.FrontSide

4
1 floppy port supports 2 FDDs with 360K, 720K, 1.2M, 1.44M and 2.88Mbytes.
2 USB2.0 ports.
1 front audio header.
Dimensions
Micro ATX Form Factor: 21.3 X 24.4cm (W X L)
B. BIOS & Software
BIOS
Award legal Bios.
Supports APM1.2.
Supports ACPI.
Supports USB Function.
Software
Supports WarpspeederTM, 9th TouchTM, FLASHER™, WinFlasherTM and StudioFun!TM
(optional).
Offers the highest performance for Windows 98 SE, Windows 2000, Windows Me,
Windows XP, SCO UNIX etc.
Package contents
HDD Cable X1
FDD Cable X1
User’s Manual X1
USB Cable X1 (optional)
Rear I/O Panel for ATX Case X1 (optional)
Fully Setup Driver CD X1
S/PDIF Cable X1 (optional)
How to setup Jumper
The illustration shows how jumpers are setup.When the Jumper cap is placed on pins, the
jumper is “close”. If no jumper cap is placed on the pins, the jumper is ”open”. The
illustration shows a 3-pin jumper whose pin 1and 2 are “close” when jumper cap is placed
on these 2 pins.
Jumper close Jumper open Pin 1-2 close

5
CPU Installation
Step1: Pull the lever sideways away from the socket and then raise the lever up to a
90-degree angle.
Step2: Look for the white dot/cut edge. The white dot/cut edge should point towards the
lever pivot. The CPU will fit only in the correct orientation.
Step3: Hold the CPU down firmly, and then close the lever.
Step4: Put the CPU fan on the CPU and buckle it. Connect the CPU fan power cable to
the JCFAN1. This completes the installation.
CPU Fan Headers: JCFAN1
Pin No. Assignment
1 Ground
2 +12V
31
JCFAN1
3 FAN rpm Rate Sense
System Fan Headers: JSFAN1
Pin No. Assignment
1 Ground
2 +12V
31
JSFAN1
3 FAN rpm Rate Sense
Step1 Step2 Step3 Step4

6
DDR DIMM Modules: DDR1/ DDR2
DRAM Access Time: 2.5V Unbuffered DDR 200/266 MHz Type required.
DRAM Type: 64MB/ 128MB/ 256MB/ 512MB/ 1GB DIMM Module (184 pin)
Total Memory Size with Unbuffered DIMMs
DIMM Socket
Location DDR Module Total Memory Size (MB)
DDR1 64MB/128MB/256MB/512MB/1GB
*1
DDR2 64MB/128MB/256MB/512MB/1GB
*1
Max is
2GB
***Only for reference***
Installing DDR Module
1. Unlock a DIMM slot by pressing the
retaining clips outward. Align a DIMM on
the slot such that the notch on the DIMM
matches the break on the slot.
2. Insert the DIMM firmly and vertically into
the slot until the retaining chip snap back in
place and the Dimm is properly seated.
Jumpers, Headers, Connectors & Slots
Floppy Disk Connector: FDD1
The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cables.
Hard Disk Connectors: IDE1/ IDE2
The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/ 66/ 100/ 133 functionality. It has two
HDD connectors IDE1 (primary) and IDE2 (secondary).
The IDE connectors can connect a master and a slave drive, so you can connect
up to four hard disk drives. The first hard drive should always be connected to
IDE1.

7
Peripheral Component Interconnect Slots: PCI 1-3
This motherboard is equipped with 3 standard PCI slots. PCI stands for Peripheral
Component Interconnect, and it is a bus standard for expansion cards. This PCI
slot is designated as 32 bits.
Accelerated Graphics Port Slot: AGP1
Your monitor will attach directly to that video card. This motherboard supports
video cards for PCI slots, but it is also equipped with an Accelerated Graphics Port
(AGP). An AGP card will take advantage of AGP technology for improved video
efficiency and performance, especially with 3D graphics.
Front Panel Connector: JPANEL1
Front USB Header: JUSB3
Pin Assignment Pin Assignment
1 +5V(fused) 2 +5V(fused)
3 USBP4- 4 USBP5-
5 USBP4+ 6 USBP5+
7 Ground 8 Ground
2
1
10
9
JUSB3 9 KEY 10 NA
SPK
PWR_LED
HLED
SLP
RST
224
IR
123
IRON/OFF
(+) (-)
(+) (-)(+)
Pin Assignment Function Pin Assignment Function
1 +5V 2 Sleep Control
3 NA 4 Ground Sleep
Button
5 NA 6 NA NA
7 Speaker
Speaker
Connector
8 Power LED (+)
9 HDD LED (+) 10 Power LED (+)
11 HDD LED (-) Hard Drive
LED 12 Power LED (-)
POWER
LED
13 Ground 14 Power Button
15 Reset Control Reset
Button 16 Ground Power-on Button
17 NA 18 KEY
19 NA 20 KEY
21 +5V 22 Ground
23 IRTX
IrDA
Connector
24 IRRX
IrDA
Connector
JPANEL1

8
Wake On LAN Header: JWOL1
Pin Assignment
1 +5V Standby
2 Ground
13
JWOL1
3 Wake up
Power Connectors: JATXPWER1
PIN Assignment PIN Assignment
1 +3.3V 11 +3.3V
2 +3.3V 12 -12V
3 Ground 13 Ground
4 +5V 14 PS_ON
5 Ground 15 Ground
6 +5V 16 Ground
7 Ground 17 Ground
8 PW_OK 18 -5V
9 Standby Voltage
+5V 19 +5V
10
1
20
11
JATXPWER1
10 +12V 20 +5V
Power Source Selection for Keyboard and Mouse: JKBV1
JKBV1 Assignment Description
1
3
Pin 1-2 close
+5V
+5V for keyboard and mouse
1
3
Pin 2-3 close
+5V Standby
Voltage
PS/2 Mouse and PS/2 Keyboard are
powered with +5V standby voltage
Note: In order to support this function “Power-on system via keyboard and
mouse, “JKBV1” jumper cap should be placed on pin 2-3.

9
Power Source Selection for USB: JUSBV1/ JUSBV2/ JUSBV3
JUSBV1/ JUSBV2/
JUSBV3 Assignment Description
1 3
Pin 1-2 close
+5V
JUSBV2: 5V for USB located at the JUSB4
port
JUSBV3: 5V for USB located at the JUSB3
port
JUSBV1: 5V for USB located at the
JUSBLAN1 port
1 3
Pin 2-3 close
+5V Standby
Voltage JUSBV2: JUSB4 port powered with standby
voltage of 5V
JUSBV3: JUSB3 port powered with standby
voltage of 5V
JUSBV1: JUSBLAN1 port powered with
standby voltage of 5V
Note: In order to support this function “Power-on the system via USB device”,
“JUSBV1/JUSBV2/JUSBV3” jumper cap should be placed on pin 2-3
respectively.
Clear CMOS Jumper: JCMOS1
!Clear CMOS Procedures:
1. Remove AC power line.
2. Set the jumper to “Pin 2-3 close”.
3. Wait for five seconds.
4. Set the jumper to “Pin 1-2 close”.
JCMOS1 Assignment
13
Pin 1-2 Close Normal Operation (default)
13
Pin 2-3 Close Clear CMOS Data
The following procedures are for resetting the
BIOS password. It is important to follow these
instructions closely.

10
5. Power on AC.
6. Reset your desired password or clear the CMOS data.
Case Open Connector: JCI1
Pin Assignment
1 Case Open Signal
1
JCI1 2 Ground
CD-ROM Audio-In Header: JCDIN1
Pin Assignment
1 Left Channel Input
2 Ground
3 Ground
1
4
JCDIN1
4 Right Channel Input
Front Panel Audio Header: JF_AUDIO
1
29 10
JF_AUDIO
Pin Assignment Pin Assignment
1 Mic In/ Center 2 Ground
3 Mic Power/ Bass 4 Audio Power
5 Right Line Out/ Right
Speaker Out 6 Right Line Out/ Right Speaker Out
7 Reserved 8 Key
9 Left Line Out/ Left
Speaker Out 10 Left Line Out/ Left Speaker Out
Digital Audio Connector: JSPDIF1
Pin Assignment
1 +5V
2 SPDIF_OUT
13
JSPDIF1 3 Ground

11
CNR Codec/ Onboard Selection: JCODECSEL
JCODECSEL Assignment
13
Pin 1-2 Close Onboard Codec is used (default)
13
Pin 2-3 Close CNR Codec is used
CPU Frequency Selection: JCLK1
JCLK1 Assignment
1
Pin 1-2 Close
100 MHz
1
Pin 1-2 Open
133 MHz
Game Port Header: JGAME1
1
216
15
JGAME1
Pin Assignment Pin Assignment
1 +5V 2 +5V
3 Joystick B Button 1 4 Joystick A Button 1
5 Joystick B Coordinate X 6 Joystick A Coordinate X
7 MIDI Output 8 Ground
9 Joystick B Coordinate Y 10 Ground
11 Joystick B Button 2 12 Joystick A Coordinate Y
13 MIDI Input 14 Joystick A Button 2
15 NA 16 +5V

12
Back Panel Connectors
PS/2
Keyboard
PS/2
Mouse Parallel
JPRNT1
JCOM1
JKBMS1
USB
JUSB4
COM1
JVGA1
VGA1 USB
JUSBLAN1
Speaker
Out
Line In
Mic In
JAUDIO
LAN
PS/2
Keyboard
PS/2
Mouse Parallel
JPRNT1
JCOM1
JKBMS1
USB
JUSB4
COM1
JVGA1
VGA1 USB
JUSBLAN1
Speaker
Out
Line In
Mic In
JAUDIO
LAN

13
Deutsch
Spezifikationen von M7VIG Pro-D
A. Hardware
CPU
Unterstützung für Sockel A.
Unterstützung für die AMD® Athlon/(ThunderbirdTM) /AthlonTM XP/DuronTM
Prozessoren
FSB mit 200/266MHz.
Chipsatz
Northbridge: VIA KM266.(VT8375)
Southbridge: VIA KT8235.
Hauptspeicher
Unterstützung für 2 DDR Geräte.
Unterstützung für 200/266 (ohne ECC) DDR Geräte
Die maximale Speichergröße ist 2GB.
Super I/O
Chip: Winbond W83697HF.
Steckplätze
Drei 32-bit PCI-Bus-Slots.
Ein AGP-Slot. (1x/ 2x/ 4x)
Onboard-IDE
Unterstützung für vier IDE Diskettenlaufwerke.
Unterstützung für PIO Modus 4, Master Modus und Ultra DMA 33/66/100/133 Bus
Master Modus.
Onboard AC’97 Sound Codec
Chip: VIA VT1612A.
Entspricht die Spezifikation von AC’97.
Unterstützung für 2-Kanal.
Onboard-Peripheriegeräte
a. FürRückwand
1 serielle Schnittstelle.
1 VGA-Schnittstelle.
1 parallele Schnittstelle. (SPP/EPP/ECP-Modus)
Audio Schnittstellen in vertikale Stellung.
1 LAN-Buchse.
Uerstützung für PS/2-Maus und PS/2-Tastatur.
4 USB 2.0-Ports.

14
b.Für Vorderseite
1 Floppy-Port mit Unterstützung für 2 Diskettenlaufwerke.(360KB, 720KB, 1.2MB,
1.44MB und 2.88MB)
2 USB 2.0-Ports.
1 Front –Audio-Header.
Abmessungen
Micro ATX Form-Factor: 21.3 X 24.4cm (W X L)
B. BIOS & Software
BIOS
Award legal Bios.
Unterstützung für APM1.2.
Unterstützung für ACPI.
Unterstützung für USB Funktion.
Software
Unterstützung für WarpspeederTM, 9th TouchTM, FLASHER™, WinFlasherTM und
StudioFun!TM. (optional)
Unterstützung für die am meisten verbreiteten Betriebsysteme wie Windows 98SE,
Windows 2000, Windows ME, Windows XP und SCO UNIX usw.
Verpackungsinhalt
HDD Kable X1
FDD Kable X1
Benutzer Handbuch X1
USB Kable X1 (optional)
I/O-Rückwand für ATX Gehäuse X1 (optional)
Treiber CD für Installation X1
S/PDIF-Kable X1 (optional)
Einstellung der Jumper
Die Abbildung verdeutlicht, wie Jumper eingestellt werden. Pins werden durch die
Jumper-Kappe verdeckt, ist der Jumper ”geschlossen”. Keine Pins werden durch die
Jumper-Kappe verdeckt, ist der Jumper “geöffnet”. Die Abbiildung zeigt einen 3-Pin
Jumper dessen Pin1 und Pin2 ”geschlossen“ sind, bzw. es befindet sich eine
Jumper-Kappe auf diesen beiden Pins.
Jumper geschlossen Jumper geöffnet Pin1-2 geschlossen

15
Installation der CPU
Schritt 1: Ziehen Sie den Hebel seitlich vom Sockel weg. Heben Sie den Hebel dann
in 90-Grad-Winkel nach oben.
Schritt 2: Suchen Sie nach der scharfen Kante, die auf Drehpunkt des Hebels
weisen muss. Die CPU passt nur, wenn sie richtig ausgerichtet ist.
Schritt 3: Drücken Sie die CPU fest in den Sockel und schließen Sie den Hebel.
Schritt 4: SteckenSieIhren CPU-Lüfterauf dieCPU.Schließen SiedieStromversorgungsstecker
fürCPU-Lüfter an JCFAN1 an. Dann beenden Sie die Installation.
CPU-Lüfter Headers: JCFAN1
Pin Belegung
1 Masse
2 +12V
31
JCFAN1
3 FAN RPM Geschwindigkeit Sensor
System-Lüfter Headers: JSFAN1
Pin Belegung
1 Masse
2 +12V
31
JSFAN1
3 FAN RPM Geschwindigkeit Sensor
Schritt 1 Schritt 2 Schritt 3 Schritt 4

16
DDR-DIMM-Modules: DDR1/ DDR2
DRAM-Zugriffszeit: 2.5V unbuffered DDR 200/266 MHz Typ erforderlich.
DRAM Typen: 64MB/ 128MB/ 256MB/ 512MB/ 1GB DIMM-Module (184-Pin)
Gesamt Speichergröße von nicht registrierter DIMMs
DIMM-Sockel
Standort DDR-Modul Speichergröße
DDR1 64MB/128MB/256MB/512MB/1GB
*1
DDR2 64MB/128MB/256MB/512MB/1GB
*1
Maximal
2 GB
**Nur als Referenz***
Installation von DDR-Modul
1. Öffnen Sie einen DIMM-Slots, indem Sie
die seitlich Chips nach außen drücken.
Richten Sie das DIMM-Modul so über dem
Slot aus, dass das Modul mit der Kerbe in
den Slot passt.
2. Drücken Sie das DIMM-Modul in den Slot,
bis die seitlichen Clips zuschnappen und
das Modul fest sitzt.
Jumpers, Headers, Anschlüsse & Slots
Diskettenanschluss: FDD1
Das Motherboard enthält einen standardmäßigen Diskettenanschluss, der 360K-,
720K-, 1.2M-, 1.44M- und 2.88M-Disketten unterstützt. Dieser Anschluss
unterstützt die mitgelieferte Bandkabel des Diskettenlaufwerks.
Festplattenanschlüsse: IDE1 und IDE2
Das Mainboard hat einen 32-Bit Enhanced PCI IDE-Controller, der die Modi
PIO0~4, Bus Master sowie die Ultra DMA/33/66/100/133- Funktion zur Verfügung
stellt. Dieser ist mit zweii HDD-Anschlüssen versehen IDE1 (primär) und IDE2
(sekundär).
Die IDE-Anschlüsse können eine Master- und eine Slave-Festplatte verbinden, so
dass bis zu 4 Festplatten angeschlossen werden können. Die erste Festplatte
sollte immer an IDE1 angeschlossen werden.

17
Peripheral Component Interconnect Slots: PCI1-3
Dieses Motherboard ist mit 3 standardmäßigen PCI-Slots ausgestattet. PCI steht
für Peripheral Component Interconnect und bezieht sich auf einem Busstandard für
Erweiterungskarten, der den älteren ISA-Busstandard in den meisten
Schnittstellen ersetzt hat. Dieser PCI-Slot ist für 32 bits vorgesehen.
Accelerated Graphics Port Slot: AGP1
Ihr Monitor wird direkt an die Grafikkarte angeschlossen. Dieses Motherboard
unterstützt Grafikkarten für PCI-Slots, aber es ist auch mit einem Accelerated
Graphics Port ausgestattet. AGP-Karten verwenden die AGP-Technologie, um die
Wirksamkeit und Leistung von Videosignalen zu verbessern, besonders wenn es
sich um 3D-Grafiken handelt.
Stromversorgungsanschluss: JATXPWER1
PIN Belegung PIN Belegung
1 +3.3V 11 +3.3V
2 +3.3V 12 -12V
3 Masse 13 Masse
4 +5V 14 PS_ON
5 Masse 15 Masse
6 +5V 16 Masse
7 Masse 17 Masse
8 PW_OK 18 -5V
9 +5V_SB 19 +5V
20
11
10
1
JATXPWR1
10 +12V 20 +5V

18
Anschlüsse für die Vorderseite: JPANEL1
*Schlüsse: Kein Pin.
Front USB Header: JUSB3
Pin Belegung Pin Belegung
1 +5V(geschmelzt) 2 +5V(geschmelzt)
3 USBP4- 4 USBP5-
5 USBP4+ 6 USBP5+
7 Masse 8 Masse
2
1
10
9
JUSB3 9 Schlüsse 10 Kein
Wake On LAN Header: JWOL1
Pin Belegung
1 +5V reservierte Spannung
2 Masse
13
JWOL1
3 Aufwecken
SPK
PWR_LED
HLED
SLP
RST
224
IR
123
IRON/OFF
(+) (-)
(+) (-)(+)
Pin Belegung Funktion Pin Belegung Funktion
1 +5V 2 Sleep Control
3 Kein 4 Masse Schlafen-
Knopf
5 Kein 6 Kein Kein
7 Lautsprecher
Lautsprecher
Anschluss
8 Power LED (+)
9 HDD LED (+) 10 Power LED (+)
11 HDD LED (-) Festplatte
LED 12 Power LED (-)
Power-
LED
13 Masse 14 Power-Knopf
15 Reset Control Zurücksetzn-
Knopf 16 Masse Power-On
Knopf
17 Kein 18 Schlüsse Kein Pin
19 Kein 20 Schlüsse
21 +5V 22 Masse
23 IRTX
IrDA-
Anschluss
24 IRRX
IrDA
Anschluss
JPANEL1