Bircher RFGate 2.2.W2.F.A Quick guide

1
12 3 4 5
ON
+
2032
23
175 189
50.8
138
10.8
4.8
80 45
121 162 178
RFGate 2.2.W2.F.A
14
4.3
57.6
1 7. 0
15.5 65.7
Wireless signal transmission system for safety edges, two channels
Translation of the original operating instructions
General
1Safety instructions
2Common application
2.1 Industrial door with wicket door
ENGLISH
349284D
10/17
Warning: Switch off the operating voltage before working on the system.
Only trained, qualied personnel may perform installation and startup.
The unit may only be opened and repaired by Bircher Reglomat employ-
ees. The switching unit may only be used to protect against dangers on
crushing and shearing points and on automatic industrial doors (intended
use). National and international regulations on industrial door safety must
be complied with. Always consider the safety functions of your applica-
Transmitter 1
DIP switch 5 ON
tion as a whole, never just in relation to one individual section of the
system. A risk assessment in advance is mandatory. The installer is re-
sponsible for installing the industrial door system correctly.
i
It is recommended to change the batteries every year.
i
Transmitter 1 Transmitter 2 Receiver
Receiver
Safety edges
8.2 kΩ
Transmitter 1 input 1 corresponds to receiver output 1
Transmitter 2 corresponds to receiver output 2
Magnet
Transmitter 2
Drilling template enclosed

2
8K2
1 2
ON
IN1 IN2 2)
1 2
ON
IN1 IN2 2)
1)
3 4 5 6 7 8
8K28K2
3 4 5 6 7 8
8K28K2
2
ON
1 2
+
+
2032
2032
1
ON
1 2
+
2032
NC 2x
i
NC
3 4 5 6 7 8
NO 5x
+/~ –/~
12/24V
AC/DC
1 2 3 4 5 6 7 8 9 10 11 12
VCC1 VCC2 COM1 OUT1 SOUT1 COM2 OUT2 SOUT2 TST1
COM.T1
TST2
COM.T2
DIP switch Sensor connection DIP switch Sensor connection
1) Change from NC to NO, see chapter 3.2
2)
i
IN2 without function
Relay contacts are shown unpowered
3.2 Changing input from NC to NO (factory setting = NC)
4.2 Wiring: Outputs and control
4.3 DIP switches
3.1 DIP switch setting according to sensor (safety edge, switching contact)
4Receiver
3Transmitter 1
Gate control
with NC input
Gate control
8.2 kOhm input
Gate control with
NO input
Remove jumper(s)
4.1 Wiring: Power supply and test inputs
1 2 3 4 5
ON *Safety application
Standard
according to EN ISO 13849-1
1 2 3 4 5
ON Inactive ➔ no safety function
(Radio connection is not monitored)
12 3 4 5
ON Transmission frequency
869.85 MHz:
Set DIP-switch before pairing transmitter –
receiver
12 3 4 5
ON *868.95 MHz:
Set DIP-switch before pairing transmitter –
receiver
12 34 5
ON Test input type
NC
activated = contact open
12 34 5
ON *NO
activated = contact closed
12 3 45
ON Automatic frequency adjustment
Active
Used only in case of severe radio disturbance
12 3 45
ON *Inactive
12 3 4 5
ON *Programming (2 transmitters)
Transmitter 1 corresponds to output 1
Transmitter 2 corresponds to output 2
12 3 4 5
ON Programming (for 2 channel transmitter)
Not for this application
*= factory setting
RFGate 2.2.S.F
1.
Insert
battery 1
4.
Insert
battery 2
2.
Status
3.
Change
5.
Change
concluded
Press button on
transmitter Status changes LED ashes
LED ashes 2x LED ashes 5x
> 1.5 sec.
After inserting battery 1, you have
10 seconds to change the status
Observe the
sequence
NO
i
Transmitter 2 is xed to NC
Test Common

3
ON
1 2
+
+
2032
2032
2
1
ON
1 2
+
2032
1 2
ON
1 2 3 4 5
ON
i
i
ON
12 3 4 5
ON
2x
2x
OK?
OK?
< 5 mm
+
3V
LITHIUM
CR 2032
+
3V
LITHIUM
CR 2032
+
3V
LITHIUM
CR 2032
+
3V
LITHIUM
CR 2032
+
6.1 Pairing the transmitter with the receiver
5Set-up
6Programming
2.
On the trans-
mitter 1 for
channel 1
On the receiver
On the receiver
Press and
release button
Beep Wait 2 beeps
10 sec.
4.
On the trans-
mitter 2 for
channel 2
Press and
release button
Beep Wait
10 sec.
3.
On the receiver
Beep BeepRelease button Release buttonLED
lights up
LED ashesPress button
> 1.5 sec.
Press
button
> 1.5 sec.
1.
On the receiver
BeepPress button
> 1.5 sec.
LED lights up
7.
Transmitter 1:
mount
Release button
4.
Transmitter 1:
insert
batteries
5.
Transmitter 2:
insert
batteries
Please observe the torque when
fastening the cover:
Max. 45 N cm
1.
Check DIP switch
settings
6.
Programming (Chapter 6.1):
pair transmitter with receiver
The distance between the trans-
mitter and receiver and additional
transmitters must be at least 1 m
2 beeps
Observe
order
Code saved
LED goes out
Code saved
LED goes out
8.
Transmitter 1:
wire
3.
Receiver:
Turn on power
supply
2.
Receiver: Install
and wire
11.
System test:
safety edge on gate
see 7.1
Beep
Beep
BeepBeep
BeepBeep
Beep
9.
Mount trans-
mitter 2 and
the magnet
10.
Note: Distance between
magnet / transmitter when
doors are closed
12.
System test wicket door:
opening and closing
see 7.1
Transmitter 1:
Transmitter 2:
Wicket
door
correctly
positioned

4
12345
ON SAB
SELECT
REL 1 REL21
R2R1
1 2
12345
ON SAB
SELECT
REL 1 REL21
R2R1
1 2
2x
4x
Bircher Reglomat AG, Wiesengasse 20, CH-8222 Beringen, www.bircher-reglomat.com
3V
LITHIUM
CR 2032
+
3V
LITHIUM
CR 2032
+
3V
LITHIUM
CR 2032
+
3V
LITHIUM
CR 2032
+
7Standard operation
9Technical data
10 EC-Declaration of Conformity
11 Contact
7.1 Receiver LED indicators
7.2 Warning indicator for low battery voltage
Object
detected
LED off
Wicket doors
open
LED off
LED 1 LED 2
Signal emitted with each activation of the transmitter
Receiver
Supply voltage 12/24 V ACDC
Transmitter memory 7 + 7
Output 2 relays 24 V, 0.5 A; micro switch-off 1B
Power consumption 0.5 W @ 12 V; 1.2 W @ 24 V
Test signal input 12/24 VACDC
Protection class IEC 60529 IP55
Transmitter 1
Battery power 2 x Lithium 3 V type CR2032
Power consumption Transmitting: 17 mA standby: 16 µA
Protection class IEC 60529 IP55
Manufacturer: Bircher Reglomat AG, Wiesengasse 20, CH-8222 Beringen
Following directives have been observed: MD 2006/42/EC, RoHS 2011/65/EU, RED 2014/53/EU
EC type-examination certicate: E6945
Notied inspection centre: Suva, technology division, SCESp 0008, ID no. 1246
Product variant: RFGate 2.1.x, RFGate 2.2.x
Safety OK Wicket doors
closed
LED on LED on
Battery voltage
low
System
Frequency bands 868.95 MHz & 869.85 MHz
Range Under optimum conditions up to 100 m
Pollution degree 2
Working temperature -20 °C to +55 °C
Transmitter 2
Battery power 2 x Lithium 3 V type CR2032
Power consumption Transmitting: 17 mA standby: 16 µA
Protection class IEC 60529 IP65
6.2 Transmitter reset (Deletion of transmitter-receiver pairing)
6.3 Memory full
Press button Hold down button Short beepsBeep WaitRelease button
10 sec.
> 1.5 sec. > 3 sec.
2 beeps
On the receiver Memory cleared
on all trans-
mitters
BeepBeep Beep BeepBeep
Beep
Beep 10 sec.
8Alternative installation with double sided tape (not supplied)
Caution!
Ensure surfaces are clean, dry and free of dust and grease.
View of transmitter 2
(bottom) Double-sided
adhesive tape
6.4 Battery change
Danish seller
Swissdoor ApS, Stenhuggervej 2, DK-5471 Soendersoe
[email protected], www.swissdoor.dk