Bismon B1-3631SFP User manual

10/100/1000Base-TX Fast Ethernet Media Converter
B1-3631SFP
( Power Inbuilt )
User’s Manual
V 1.0

1. Overview
The Media Converter complies with IEEE802.3z,IEEE802.3AB Standards. It is
designed to convert data signal between 10/100/1000 Base-T and 1000Base-SX/LX fast
Ethernet. It supports 10/100/1000Base-T and 1000Base-SX/LX applications. The data signal
converted by such high performance media converter can be transmitted up to 120Km
maximum by fiber-optical cable.
The Converter is equipped with two fiber optic connectors (One for transmitting-TX and
another for receiving-RX) and one RJ-45 Jacks and one external power supply receptacle.
Six LED indicators are built-in for easy diagnosing and monitoring the status of power,
Unshielded Twisted Paired (UTP) Link, UTP Activity, Fiber Link, Fiber Activity, Full duplex
and data rates. It can be configured automatically for Full Duplex or Half Duplex operation.
It is compact, cost-effective, low dissipative, high reliable and stable. It can be used in
standalone applications, or Rack-Mounted applications where multiple media converter
can be inserted into a rack-mount chassis (Up 16 units), and allowing all the converters to
be powered by a single internal power supply.
BISMON Datacomms Solutions
www.bismon.com

2. Specifications:
2.1 Performance introduction (Table 1)
Table 1: performance introduction
*Note: Please refer to Specifications.
2.2 Appearance (Fig.2, Table2)
fig.2 Front Panel
LED Color Funtion
RX Green The light on means the TX
port is receiving data
TX Green The light on means the TX
port is transmitting data
3. Power Inbuilt
Input: 85265VAC or -48VDC
Output: 2A, +5VDC
4. Check list
Before you start installing the Converter, verify the package contains the following:
1) The 10/100/1000Base-T to 1000Base-S X/LX Ethernet Media Converter-h1
2) The Power line----------------------h1
3) This User’s Manual-----------------h1
Please notify your sales representative immediately if any of the aforementioned items is
missing or damaged.
5.Installing the Converter
5.1 For as a standalone unit:
Parameter Type
Data rate (Mbps) 10/100 /1000
Optical wavelength
(nm)
850,1310, 1550(for over
60Km long distance)*
Fiber type(m) Single mode 9/125*
Multi-mode 50/125*
Connector type LC
Max distance (km) 20,40,60,100*
Power supply 85265VAC 50/60Hz
Operating temperature 070ć
Storage temperature -4080ć
Relative humidity 5% to 90% non
condensing
BISMON Datacomms Solutions
www.bismon.com

5.1.1 Verify if the adapter conforms to your country power requirement then insert the power
plug
5.1.2 Check the type of UTP (see fig.3)
UTP complies with IEEE802.3 Standards, and has two types: T568A T568B.
G G O B B O P P O O G B B G P P
Fig.3 The type of UTP
NOTE: G: Green˗O: Orange˗B: Blue˗P: Palm
Parallel cable: connect T568A to T568A , or T568B to T568B
Crossing-over cable: connect T568A to T568B
5.1.3 TP port list (Fig.4)
5.2 Installing
5.21 TP port installing
Media converter autodetect and connect the parallel lines RJ-45 port or the cross lines the
RJ-45 port.
5.22 Fiber port installing
Connect the fiber-optic transceiver on the media converter with the Single-mode SC fiber
connectors.
5.23 Connect to switch power adaptor
5.24 Check the appearance that converter instructions light
If connection right, the POW, TP/1000 LED is bright; Otherwise checking the Fiber port and
TP port.
Note: Connecting to Router, Bridge or Switch, please refer to the device’s Technical
Manual.
BISMON Datacomms Solutions
www.bismon.com