Bissell Auto Care Proheat 1425 SERIES User manual

2Thanks/Consumer Services
Safety Instructions
Product View
This Guide/Features
Special Tools/Assembly
Clean-Up/Storage
Troubleshooting
Replacement Parts
3
4
5
6–8
8–9
10
11
USER’S GUIDE
1425 Series
Warranty
12
Auto Care
Proheat
®
COMPACT DEEP CLEANER
Operation
6–8

2
We’re glad you purchased a BISSELL Auto Care Proheat®. Everything we
know about floor care went into the design and construction of this
complete, high-tech home cleaning system.
Your Auto Care Proheat® is well made, and we back it with a limited one-
year warranty. We also stand behind it with a knowledgeable, dedicated
Consumer Services department, so, should you ever have a problem, you’ll
receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is
a global leader in the design, manufacture, and service of high quality
homecare products like your Auto Care Proheat®.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
President and Chief Executive Officer
Thanks for buying a BISSELL Auto Care Proheat®
2 www.bissell.ca 1-800-263-2535
BISSELL Consumer Services
For information about repairs or replacement parts, or questions about your warranty, call:
BISSELL Consumer Services
1-800-263-2535
Monday — Friday 8 a.m. — 10 p.m. ET
Saturday 9 a.m. — 8 p.m. ET
Or write:
BISSELL Canada Corporation
Box 1003
Niagara Falls, ON L2E 6W2
ATTN: Consumer Services
Or visit the BISSELL website — www.bissell.ca
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event
of a warranty claim. See “Warranty” on page 12 for details.

3
3
www.bissell.ca 1-800-263-2535
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions
should be observed, including the following:
Read all instructions before using your Auto Care
Proheat®
WARNING: To reduce the
risk of fire, electric shock, or injury:
■Do not use for any purpose other than described
in this User’s Guide.
■Use only BISSELL cleaning products intended
for use in this appliance.
■Use only manufacturer’s recommended attach-
ments.
■Do not expose to rain, store indoors.
■Do not handle Auto Care Proheat® plug or
appliance with wet hands.
■Do not leave Auto Care Proheat® when it is
plugged in.
■Do not put any object into appliance openings or
use with blocked openings. Keep free of dust, lint,
hair, and anything that may reduce air flow.
■Do not expose hair, loose clothing, fingers or
body parts to openings or moving parts.
■Keep appliance on a level surface.
■Be extra careful when cleaning stairs.
■Do not carry the appliance while in use.
■Never spray at people or animals.
■Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
■Do not pick up hot or burning objects.
■Do not pick up flammable or combustible materials
(lighter fluid, gasoline, kerosene, etc.) or use in the
presence of explosive liquids or vapour.
■Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, gasoline, etc.).
■Do not use appliance in an enclosed space filled with
vapours given off by oil base paint, paint thinner,
some moth proofing substances, flammable dust, or
other explosive or toxic vapours.
■Do not pull or carry by cord, use cord as a
handle, close door on cord, pull cord around
sharp corners or edges, run appliance over cord,
or expose cord to heated surfaces.
■Do not use with damaged cord or plug.
■Turn off all controls before unplugging.
■Unplug before attaching the TurboBrush.
■Unplug from outlet when not in use and before
conducting maintenance and troubleshooting.
■Unplug by grasping the plug, not the cord. Do not
unplug by pulling on cord.
■Do not use Auto Care Proheat® if it has been
dropped, damaged, left outdoors or dropped into
water. Have it repaired at an Authorized Service
Centre.
■Always connect to a properly grounded outlet; see
grounding instructions.
■Do not modify the 3-prong grounded plug.
SAVE THESE
INSTRUCTIONS
GROUNDING INSTRUCTIONS
This appliance must be connected to a grounded
wiring system. If it should malfunction or break
down, grounding provides a safe path of least
resistance for electrical current, reducing the risk of
electrical shock. The cord for this appliance has an
equipment-grounding conductor and a grounding
plug. It must only be plugged into an outlet that is
properly installed and grounded in accordance with
all local codes and ordinances.
WARNING: Improper
connection of the equipment-grounding
conductor can result in a risk of
electrical shock. Check with a qualified
electrician or service person if you
aren’t sure if the outlet is properly
grounded. DO NOT MODIFY THE PLUG.
If it will not fit the outlet, have a
proper outlet installed by a qualified
electrician. This appliance is designed
for use on a nominal 120-volt circuit,
and has a grounding attachment plug
that looks like the plug in the drawing
above. Make certain that the appliance
is connected to an outlet having the
same configuration as the plug. No
plug adapter should be used with
this appliance.
This model is for household use only.
Grounded
Outlets
Grounding Pin

4 www.bissell.ca 1-800-263-2535
Power Switch
Clean/
Solution Tank
Dirty/Collection Tank
Built-In Heater Switch*
*Select Models only
Heat Indicator Light*
*Select Models only
Flex Hose Clip
Tough Stain Tool
TurboBrushTM*
*Select Models only
Vacuum Flex Hose
with Spray Trigger
TurboBrushTM Clip*
*Select Models only
Quick ReleaseTM Cord Wrap
Power Cord
These items are available for purchase with your model. To order replacement parts or additional tools or formulas, please
refer to page 11.
Optional Accessories:
4” (10 cm) Tool 6” (10 cm) Tool TurboBrush Spraying, Sliding
Crevice Tool w/
Brush
32 oz (946 mL)
Little GreenTM
Formula
64 oz (1.89 L)
Pet odor &
Stain RemovalTM
Formula
32 oz (946 mL)
Auto Cleansing
FormulaTM

5
www.bissell.ca 1-800-263-2535
How To Use This Guide
Please read this Guide thoroughly before
assembling your cleaner. Pay particular
attention to the product diagram, assembly
instructions, and part names.
1. Begin by locating and organizing all parts
before assembly.
2. Familiarize yourself with the parts and where they go.
Following this User’s Guide will let you get the
best performance from your BISSELL Auto Care
Proheat® for many years.
The Clean/Solution Tank is the tank to your
left as you face the unit looking at the black
power switch.
The Dirty/Collection Tank is the tank to your right
as you face the unit looking at the black power
switch.
The Auto Care Proheat® models give you
the ability to raise the water temperature for
improved cleaning performance based on your
cleaning needs.
After turning the Built-In Heater Switch on, the
Heat Indicator Light will illuminate, indicating the
heater has reached the correct temperature.
The clip guides the storage of the vacuum flex
hose around the unit.
Attaches to the unit for storage of
the TurboBrush.
The standard tool that attaches to the Vacuum
Flex Hose.
To remove the Power Cord, gently twist/rotate
the Quick Release Cord Wrap clockwise.
Auto Care Proheat® Product Features
Clean/Solution Tank
Dirty/Collection Tank
Built-In Heater Switch (Red)
Heat Indicator Light
Flex Hose Clip
TurboBrush Clip
Tough Stain Tool
Quick Release Cord Wrap

The Power Cord, with a three-prong plug, stores
on the back of the Auto Care Proheat® by wrap-
ping around the Quick-Release Cord Wrap.
NOTE: Unwrap the Power Cord completely before
operating the unit.
Assembling your Auto Care Proheat®
is a simple process.
1. Take the Flex Hose Clip and slide the back plate
into the opening on the front of the unit. You will
hear a “snap” when it is locked in place.
If your model includes a TurboBrush,
2. Slide the TurboBrush Clip into the guides on the
Vacuum Flex Hose storage bracket, on the back of
the unit.
Auto Care Proheat® Product Features (Continued)
Putting It Together
6 www.bissell.ca 1-800-263-2535
12
WARNING:
Do not use this product while on
any type of ladder. Do not place
the product in a place where
it will be stepped on or kicked
while in use. Do not place the
product on an elevated surface
where it may be pulled off the
surface while in use.
WARNING:
Do not use an extension cord with
this product. The use of an extension
cord may result in a severe electrical
shock, particularly if the extension
cord does not have an electrical
rating higher than that of the product,
OR if the extension cord does not
have a three-prong grounding plug
and if the extension cord is not
plugged into a circuit box with a
ground fault circuit interrupter. Safety
precautions such as keeping all
connections off the ground and dry
will not eliminate the danger.
WARNING:
Use only BISSELL compact clean-
ing formulas in your cleaner. Use
of cleaning formulas which con-
tain lemon or pine oil may dam-
age this appliance and void the
warranty. Chemical spot cleaners
or solvent-based soil removers
also should not be used. These
products may react with the plas-
tic materials used in your cleaner,
causing cracking or pitting.
Power Cord

Getting Ready
7
www.bissell.ca 1-800-263-2535
1. To Fill the Clean/Solution Tank.
A.Remove the tank by lifting it straight up and
then away from the unit.
B.Unscrew the black cap at the bottom of the
Clean/Solution Tank.
C.Add BISSELL Auto Cleansing Formula to the
FORMULA fill line (8 oz.) on the Clean/Solution
Tank.
Fill the Clean/Solution Tank with hot (NOT boiling)
tap water to the WATER fill line.
Replace and tighten the black cap.
D. Replace the Clean/Solution Tank by lining up the
vertical guides on the left side of the unit with
the indentations on the Clean/Solution Tank and
gently sliding it down into position.
2. Unwrap Vacuum Flex Hose completely from
Onboard Hose Storage.
3. Attach your selected cleaning tool to the Spray
Trigger Unit by pressing tool onto Spray Trigger
firmly until the button lock snaps into hole. Make
certain the tool is securely attached.
4. Twist the Quick Release Cord Wrap clockwise to unwrap
the Power Cord completely from Onboard Cord Storage
and plug into 120 Volt, 60 Hz grounded outlet as
described in Important Safety Instructions, page 3.
5. Press Power Switch to ON Position.
NOTE: If your unit has a built-in heater, first turn
the black power switch to “ON,” then the red
heater switch to “ON”. Within 30 seconds, the
Heat Indicator light will illuminate , indicating
the heater has reached the proper temperature.
Begin by pressing the Spray Trigger for 5-10
seconds to allow the non-heated water to travel
through the heater. Now the heated water and
cleaning solution mixture are ready to clean
carpet or upholstery. See below for detailed
cleaning instructions.
6. Press and hold Spray Trigger—spray will start in a
few seconds. Raise the tool slightly to check for spray.
Cleaning effectiveness will be enhanced if you
pre-treat heavily stained or highly-soiled areas.
Here’s how to do it:
1. Hold the Cleaning Tool just above the surface of
the carpet or upholstery to be cleaned. Press the
trigger to release a spray of cleaning solution
directly onto the soiled area.
2. Wait 3-5 minutes before cleaning.
Pre-Treating
WARNING:
Be sure to unplug the
cord before attaching
the TurboBrush.
1A
2
34
Power Switch
Heat
Indicator
Light
Heater Switch
56
1B
1C 1D

1. Hold the tool approximately 1” (2.5 cm) above the
soiled surface. Press the Spray Trigger to apply
the cleaning solution to the soiled area.
2. Using the brush on the tool, gently scrub the area
to be cleaned.
Note: If using the TurboBrush, the switch
should be in the “BRUSH” position. This
activates the brush only.
3. For thorough cleaning, spray additional solution,
while the brush and suction are in contact with
the surface.
4. Apply downward pressure on the tool and pull it
toward you. The suction will remove the dirt and
cleaning solution. Continue until no more dirt can
be removed.
Note: If using the TurboBrush, move the
switch to the “SUCTION” position. This
activates the suction to remove the dirt and
cleaning solution. Move the switch back to
the “BRUSH” position for additional brush-
ing action.
5. As a final step, use “drying strokes” (by not press-
ing the Spray Trigger) to remove as much liquid/
moisture as possible. Repeat this step as often as
necessary.
Note: If using the TurboBrush, move the
switch to the “SUCTION” position. This
activates the suction to remove the dirt and
cleaning solution.
1. Turn Power Switch and Heater Switch to OFF posi-
tion.
2. Unplug Power Cord from outlet.
Note: If a significant amount of Auto Care
Proheat® formula/water remains, it is all
right to leave it in the Clean/Solution Tank
for your next cleaning task.
3. Empty and rinse the Dirty/Collection Tank after
each use, OR when dirty water reaches the
indicated maximum fill line. To remove the tank,
lift up the Dirty/Collection Tank retainer lever and
remove the tank from the unit.
BR U SH SU C TI O N
8 www.bissell.ca 1-800-263-2535
Cleaning with your Auto Care Proheat®
IMPORTANT:
Check the manufacturer’s tag before
cleaning upholstery. “W” or “WS” on the
tag means you can use your Auto Care
Proheat®. If tag is coded with an “S”
(with diagonal strike-through), or says
“Dry Clean Only,” do not proceed. If man-
ufacturer’s tag is missing or not coded,
check with your furniture dealer.
Tip:
Deep clean-
ing stairs and
high-traffic
areas on a
regular basis
can prolong
carpet life.
Tip:
Check upholstery
stuffing before
cleaning. Coloured
stuffing may bleed
through the fabric
when it becomes
wet.
After Cleaning
Tip:
Before turning off the Auto Care
Proheat®, vacuum up clean
water to thoroughly rinse out
the interior of the Vacuum Flex
Hose. Then, lift the cleaning
tool and point it upwards to
drain any remaining water into
the Dirty/Collection Tank.
Retainer Lever
3

4. Disconnect the cleaning tool from the Spray
Trigger by pushing down on button lock and pull-
ing straight off
(Do NOT twist tools to remove them)
5. Once removed from the Spray Trigger, all tools
can be cleaned by rinsing under clean running
water. The TurboBrush tool’s switch must be in
“SUCTION” position before rinsing under clean
running water.
6. Check Spray Nozzle for accumulated dirt or debris.
If necessary, clean with soft bristle brush.
1. Wipe all surfaces with a soft cloth.
2. Wrap Power Cord around the Cord Wrap on the
back of the Auto Care Proheat®.
3. Wrap Vacuum Flex Hose around the base of the
unit and secure the Spray Trigger.
4. Store unit in protected, dry area, at room
temperature (40º to 110ºF).
Note: Onboard storage for the TurboBrush
Tool has been provided on the back of the
unit. Attach the TurboBrush to the unit by
pressing it onto the holder firmly until the
button snaps into hole.
After Cleaning (continued)
Machine Storage
9
www.bissell.ca 1-800-263-2535
WARNING:
Keep spray away from face.
Failure to do so may result in
personal injury.

Troubleshooting
10 www.bissell.ca 1-800-263-2535
Water & Formula are draining out from the clean tank
Possible Causes Remedies
1. Power cord not plugged in 1. Check electrical plug
2. Blown fuse/tripped breaker 2. Replace household fuse or
reset breaker
Reduced spray or no spray
Possible Causes Remedies
1. Spray Nozzle clogged 1. Clean Spray Nozzle
2. Clean/Solution Tank empty 2. Check/Refill Tank
3. Clean/Solution Tank insert clogged 3. Clean insert at bottom of
Clean/Solution Tank
Reset breaker
4. Pump needs priming 4. Gently lift Clean/Solution
Tank while depressing the
Spray Trigger OR Gently
squeeze clean tank while
depressing Spray Trigger
Deep Cleaner won’t pick up cleaning solution
Possible Causes Remedies
1. Poor Upholstery/Carpet Tool position 1. Reposition Upholstery/Carpet
Tool on surface, follow
recommended cleaning
procedures
2. Dirty/Collection Tank is full 2. Empty Dirty/Collection Tank
3. Upholstery/Carpet Tool Brush worn 3. Replace with new Brush
4. Excess solution in Vacuum Flex Hose 4. Lift Tool and point upwards
to allow water in Hose to
flow into the
Dirty/Collection Tank
5. Incorrect Cleaning Formula 5. Use BISSELL Auto Cleansing
Formula, BISSELL Little Green
Formula ou BISSELL Pet Odor &
Stain Formula
TurboBrush attachment-Brush will not turn
Possible Causes Remedies
1. Incorrect switch position on TurboBrush 1. Reposition switch to
Brush position
TurboBrush attachment– No Suction
Possible Causes Remedies
1. Incorrect switch position on TurboBrush 1. Reposition switch to
Brush position
Thank you for selecting a BISSELL product.
Please do not return this product to the store
For any question or concern, BISSELL is happy to be of service.
Contact us directly at, 1-800-263-2535

11
Replacement parts -
11
www.bissell.ca 1-800-263-2535
1 2 345
67 8 9 10
13 14
Item Part No. Part Name
1 203-6868 4” (10 cm) Upholstery/Carpet Tool- Dusk
2 203-6869 6” (15 cm) Upholstery/Carpet Tool - Dusk
3 203-0116 Spraying, Sliding Crevice Tool w/ Brush
4 314-9162 Tough Stain Tool- Dusk
5 203-6652 TurboBrush - Dusk
6 203-5008 Clean/Solution Tank (includes cap and insert assembly)
7 203-5009 Collection/Dirty Tank (includes the airstack and float assembly)
8 203-5011 Quick Release Cord Wrap
9 203-6870 TurboBrush Clip
10 203-6871 Flex Hose Clip
11 203-5014 Cap & Insert Assembly
CLEANING FORMULAS
12 499 32 oz (946 mL) Little Green Formula Formula
13 797 64 oz (1.89 L) Pet odor & Stain RemovalTM Formula
14 98H6 32 oz (946 mL) Auto Cleansing FormulaTM
11 12

12 www.bissell.ca 1-800-263-2535
Warranty
If you need additional instruction regarding this warranty or have questions regarding what it may cover,
please contact BISSELL Consumer Services by e-mail, telephone, or regular mail as described below.
Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product, BISSELL
Canada Corporation will repair or replace (with new or remanufactured components or products), at
BISSELL’s option, free of charge from the date of purchase by the original purchaser, for one year any
defective or malfunctioning part.
See information below on “If your BISSELL product should require service”.
This warranty applies to product used for personal, and not commercial or rental service. This warranty
does not apply to routine maintenance components such as belts or brushes. Damage or malfunction
caused by negligence, abuse, or use not in accordance with the User’s Guide is not covered.
If your BISSELL product should require service:
Call BISSELL Consumer Services at the number listed below or visit the BISSELL website — www.bissell.
ca to locate a BISSELL Authorized Service Centre in your area. If there are no authorized BISSELL Service
Centres in your area, a BISSELL Representative at [email protected] or at the phone number
below will issue you a Return Authorization Number and a pre-paid mailing label to return the unit to
BISSELL for warranty repair.
The machine should be returned with a photocopy of your proof of purchase. (Your dated sales receipt is
your warranty — do not send original.) If you need information about repairs or replacement parts, or if you
have questions about your warranty, contact BISSELL Consumer Services.
E-mail: [email protected]
Or call: BISSELL Consumer Services
1-800-263-2535
Monday – Friday 8 a.m. – 10 p.m. ET
Saturday 9 a.m. – 8 p.m. ET
Or write: BISSELL Canada Corporation
ATTN: Consumer Services
Box 1003,
Niagara Falls, ON L2E 6W2
BISSELL CANADA CORPORATION IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY
NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE
PURCHASE PRICE OF THE PRODUCT.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN. ANY
IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE ONE YEAR DURATION
FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
©2008 BISSELL Homecare, Inc
BISSELL Canada Corporation
Niagara Falls, ON L2E 6S5
All rights reserved. Printed in Korea
Part Number 120-4059
Rev 10/08
Visit our website at:
www.bissell.ca