Bissell CLEANVIEW 3583 SERIES User manual

®
<
III
3583, 7636, 3247,
2970, 8531 SERIES
_Product images may vary

)RTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT VACUUM.
Alwaysconnecttoapolarizedoutlet(oneslotiswiderthantheother).Unphgfromoutletwhennotinuseandbeforeconductingmaintenance.
Whenusinganelectricalappliance,basicprecautionsshouldbeobserved,includingthefollowing: !
THERISKOFFIRE,
OR INJURY:
;connect to apolarized
(one slot iswider than the
). Donot modify the polar-
plug to fit a non-polarized
cord.
not leavevacuum cleaner
it isplugged in.Unplug
when not in use
nd beforeservicing.
_o not use outdoors or on
wet surfaces.
Do not allow to be usedas atoy.
Closeattention is necessarywhen
used by or nearchildren.
>)Do not use for any purpose other
than described in this User's
Guide.Use only manufacturer's
recommended attachments.
>)Do not usewith damaged cord or
plug. Ifapplianceisnot working
as it should,has been dropped,
damaged,left outdoors,or
dropped into water,haveit repaired
at anauthorizedservicecenter,
Do not pull or carry by cord, use
cord asa handle,closea door on
cord,or pullcord around sharp
edges or corners.Do not run
applianceovercord. Keepcord
away from heated surfaces.
Do not unplug by pulling on
cord. To unplug,grasp the plug,
not the cord.
Hold plug when rewindingonto
cord reel.Do not allow plug to
whip when rewinding.
Do not handle plug or vacuum
cleanerwith wet hands.
Do not put any object into
openings. Donot usewith any
opening blocked; keepopenings
free of dust, lint,hair,andanything
that mayreduce air flow.
Keep hair,looseclothing, fingers,
and allparts of body away from
openings and moving parts.
_)Turnoff allcontrols before
plugging or unplugging
vacuum cleaner.
_)Use extracarewhen cleaning
on stairs.
_)Do not useto pick upflammable
or combustible materials(lighter
fluid, gasoline,kerosene,etc.)
or usein areaswhere they may
be present,
_)Do not usevacuum cleanerin an
enclosedspace filled with vapors
givenoff by oil base paint, paint
thinner,some moth proofing
substances,flammable dust, or
other explosiveor toxic vapors,
>)Do not useto pick uptoxic
material (chlorinebleach,
ammonia,draincleaner,etc.).
_)Do not pick upanything that is
burning or smoking,suchas
cigarettes, matches,or hot ashes,
_)Do not usewithout filters in place,
_)Do not pick up hardor sharp
objects suchas glass,nails,screws,
coins,etc.
_)Useonly on dry,indoor surfaces,
_)Keep applianceon alevelsurface,
_)Do not carry the vacuumcleaner
while it isrunning,
_)Unplug before connecting
or disconnectingthe TurboBrush®
Tool or TurboEraser®Pet Tool
(on select models),
SAVE THESE INSTRUCTIONS
FOR FUTURE USE
Thismodelisforhouseholduseonly.
THIS APPLIANCE HAS A
POLARIZED PLUG
Toreducetheriskofelectricshock,thisappliancehasapolarizedplug(onebladeiswiderthantheother).Thisplugwillfitina
polarizedoutletonlyoneway.Iftheplugdoesnotfitfullyintheoutlet,reversetheplug.Ifitstilldoesnotfit,contactaqualified
electriciantoinstallaproperoutlet.Donotchangethepluginanywav.
......._i_iiiii,!i_:

,,,,,'s,,'
....... ,ii,i!!b
A. Vacuum Base F. Dusting Brush
B. Handle G. Hose
C. Screws (2) H. Crevice Tool _
D. Hose Wand Clip I. Extension Wand
E. TurboBrush_R/TurboEraser R J. Pet Hair Corner Tool
Pet tool (on select models) (on select models)
_Note: Crevice tool is located inside Extension Wand
Assembly
1, Slide handle onto machine base
2, Screw 2 screws into existing holes with Phillips-head
screwdriver
3, Insert extension wand clip into back of vacuum base
and twist clockwise
4, Line up tabs on the cuff of the hose with the notches
on back of vacuum, twist hose clockwise to lock into place
5, Slide other end of hose into hose wand base and place
hose over upper hose wrap
6, Slide tools into place
*Productimagesmayvary www.BISSELL.com 8OO.257.7691 5

We're glad you purchased a BISSELL
vacuum. Everything we know about
floor care went into the design and
construction of this complete,
high-tech home cleaning system.
Your BISSELL vacuum is well made,
and we back it with a limited
three-year warranty. We also stand
behind it with aknowledgeable,
dedicated Consumer Care
department, so, should you ever
have a problem, you'll receive fast,
considerate assistance.
My great-grandfather invented the
floor sweeper in t876. Today, BISSELL
is a global leader in the design,
manufacture, and service of high
quality homecare products like your
BISSELL vacuum.
Thanks again, from all of us
at BISSELL.
Mark J. Bissett
Chairman & CEO
Safety Instructions ........... 2
Quick Start Guide ............ 3
Product View ................ 5
Assembly ................... 6
Operations ................ 7-9
Maintenance & Care ...... 942
Troubleshooting ............ 13
Replacement Parts ......... 14
Warranty ................... 15
Service ..................... 15
Product Registration ........ 16
Consumer Care ............. 16
www.BlSSELLcom _r 800.237.7691
4

] Handle
2 Powerswitch**
3 TankReleaseButton
4 CarryHandle
5 SuctionPowerlndicator**
6 LidReleaseButton
7 Re-MotorFilter(located
insideDirtTanklid)
8 BottomEasyEmptyTM
DirtTank
9 CordRewind
10Post-MotorFilter
11HeightAdjustmentKnob
12BrushRollOn/Off**
13FurnitureProtectionGuard
14Powerfoot
15CordClip
16TurboBrush_YTurboEraseP
PetTool**
17UpperHoseWrap
18DustingBrush
19StretchHose
20CreviceTool(Grey)
21ExtensionWand
22ExtensionWandClip
25PowerSwitch**
24HoseWand
25HoseWandBase
26HandleReleasePedal
27FootHose
AWARNING
Plasticfilmcanbedangerous,Toavoid
dangerofsuffocation,keepawayfrom
babiesandchildren.
AWARNING
Donotpluginyourvacuumcleaneruntil
youarefamiliarwithallinstructionsand
operatingprocedures,
AWARNING
Toreducetheriskofelectricshock,turn
powerswitchoffanddisconnectpolarized
plugfromelectricaloutletbeforeperforming
maintenanceortroubleshootingchecks.
*Productimagesmayvary
**Onselectmodels www.BISSELL,_

you'llneed__assembleyour
eanerisaPhillips-headscrewdriver.
handle to vacuum
vacuum handle and remove the
taped to the handle. The screw
:ontains two screws of equal length.
the vacuum upright and slide the
handle firmly into the opening at
of the vacuum body
_ck to be sure the handle is fitted to the
Jm body. If there are any gaps between
_andle and the vacuum base, continue to
the handle firmly into the base until the
idle is flush
Insert the two screws from the screw packet
the existing holes. Push each screw firmly
_to the hole before beginning to secure the
_crew with a Phillips head screwdriver. If the
handle is aligned properly on the vacuum base,
you should be able to push the screw almost
entirely into the hole until only the screw head
is visible. Tighten the screw with a Phillips head
screwdriver by rotating the screw clockwise.
2,
4,
AWARNING
Donot0peBtevacuumwithdamp0rwetfilters
orwithoutallfilteBinplacefiBt.
Attach vacuum hose_ clips &tools
1. Attach the extension wand clip by inserting
the clip into the back of the vacuum base 1.
and twisting clockwise. Mount the extension
wand (with crevice tool inside) on the back
of the vacuum.
2. Attach the Twist 'n Snap T"hose by lining
up the tabs on the cuff with the corresponding
notches on the back of the vacuum. Twist the
Twist 'n Snap hose clockwise to lock the hose
into place.
3. Slide the end of the hose wand into the
hose wand base, and fold the hose over the
upper hose wrap.
NOTE: The powerfoot will not suction properly 2.
unless the hose wand is firmly attached.
4. Slide the dusting brush into the opening
below the upper hose wrap.
3.

Power switch
The Power switch on model 3583 is located on
the left side of the vacuum. Push the rocker
switch "ON" (I) to vacuum, and "OFF" (0) when
cleaning is complete. The Power switch on
models 7636, 3247, 2970, and 8531 is located
on the front of the handle. Push the button (_
once to vacuum, and push the button (_ again
when cleaning is complete.
NOTE: You can find your model number on the
back, bottom side of the vacuum on the white
sticker by the UL rating.
Handle position
Press the handle release pedal with your foot
to place your CleanView vacuum into one of
three cleaning positions.
1. Upright - For storage and above floor
cleaning with tools.
2. Normal cleaning - Press handle release
for household floor cleaning tasks.
3. Low cleaning - With the vacuum in
normal cleaning position, press handle release
pedal again, use for reaching under low furniture
such as tables, chairs or beds.
Hei_lht adjustment
There are five height settings available for
various floor surfaces. Turn the dial on the foot
of the cleaner to the desired setting.
Lowest setting - For low pile carpet or bare
floors. To pick up debris, it may be necessary
to move up one setting.
Medium setting - For medium pile carpet.
Highest setting - For high pile and most
shag carpet.
NOTE: For optimal carpet cleaning performance,
adjust to the lowest practical setting. If your
cleaner is difficult to push, adjust to the next
higher setting.
If the dial is difficult to turn, tilt the cleaner
back slightly to take the weight off the foot
while turning.
Transportin_l cleaner
1. To move your cleaner from room to room, put
the handle in the upright position, tilt the cleaner
back on its rear wheels and push forward.
2. The cleaner can also be moved by using the
carrying handle.
ACAUTION
Beforeusingv0urvacuum,makesurethatthedi_
tankisinthe10(kedpositionandthatbothfilters
(prem0t0randp0st-m0t0r)areinplace.Donot
operatev0urvacuumwithoutthesefilters.
*Productimagesmayvary www.BISSELL.com 800,237.7691 7

Suction Power Indicator
(On model series: 7636, 3247, 2970, 8531)
The suction power indicator tells you when the
air flow in your vacuum is reduced due to dirty
filters or a clog in the hose. The suction power
indicator will remain green until the airflow is
reduced. At that time, it begins to change to red.
When it is fully red, the airflow is significantly
reduced by a dirty filter or clog. Follow the steps
on page 12 for clearing a clog. Follow the steps
on pages 9 and 10 to clean your filters. All filters
in the vacuum should be cleaned or replaced
when the clean filter indicator turns red.
NOTE: When your vacuum is turned off, the
suction power indicator will go to the green
color setting. The suction power indicator
only detects reductions in airflow when the
vacuum power is on.
Special tools
Your BISSELL CleanView vacuum is not only a
powerful carpet and rug vacuum cleaner, it's also
a versatile above floor vacuum cleaner when you
select one of the special tools.
1. Raise handle to upright position.
2. Grasp the hose wand and separate from the
hose wand base.
3. Attach tools by firmly pushing onto vacuum
hose or extension wand.
a. Crevice Tool Use in tight narrow spaces.
b. Dusting Brush Use brush to dust
furniture, blinds, books, lamps, shelves
and baseboards.
NOTICE
Pet Hair Lifter (model 8531)
Justvacuumlikeyounormallywouldandthepethair
lifterwillgrabpethairwhenV0upullbackandsuction
itupwhenyoupushforward.
a. c.
c. Extension Wand Use with desired
attachment for a longer reach.
d. TurboBrush®/TurboEraser® Pet Tool
(models 7636 &8531) Use rotating brush
action for small flat areas such as stairs and
cushions. Press gently down and pull toward
you in a raking motion; too much pressure
will cause the brush to stop rotating.
e. Pet Hair Corner Tool (model 7636)
Use tool in corners of room or stairs to pick
up annoying dirt left stuck in the corners.
Automatic Cord Rewind
1. Gently pull out power cord and stop when
yellow is visible. Do not pull power cord beyond
the red line. Plug cord into electrical outlet.
2. To return cord, turn vacuum power switch
off, and remove plug from outlet. Hold plug and
press automatic cord button to wind cord into
reel. Do not allow plug to whip when rewinding.
www.BISSELL.com _r 8OO.237.7691
d. e.
AWARNING
For models without a BrushRollOn/
Off switch(3583, 7636, 3247). Ther0tatin¢
floorbrushcontinuestorotatewhiletoolsareinuse.To
reducetheriskofinjuryfrommovingpa_s,alwaysmove
thecleanerwiththecarryinghandleatthebackofthe
cleaner.Alwaysplacevacuumcleaneronfloorwithhandle
inuprightpositionwhenusingtools.Neverplacey0ur
fingersunderthecleanerwhenitisrunning.Neverplace
p0werfootonfurnitureorunevensurfaces.Donotplace
vacuumcleanercloseenoughto0bje_st0pulltheminto
rotatingbrush.

Brush Roll On/Off
(On Model Series: 2970 & 8531)
The rotating brush On/Off pedal is located on
the front of the vacuum base. You can use your
foot to engage or disengage this pedal Ca).
When the brush roll pedal has been engaged,
the brush will start rotating. The brush roll should
be turned on for most carpeted floors. To turn the
brush roll off, disengage the pedal by pressing
on it with your foot. We recommend turning off
the brush roll for bare floor cleaning to prevent
scatter or for other delicate surfaces.
NOTICE
Thefloorbrushwillcontinuetorotatewhiley0uusey0ur
vacuumforabovefloorcleaning.Topreventcarpetdamage,
donotleanonthevacuumorletthep0werf00ttiltf0_ard.
Thiseffectsmodelswithoutabrushr0110n/0ffswitch.
a,
To maintain maximum cleaning performance, the
following maintenance steps must be performed:
1. Empty the dirt tank when the dirt reaches the
"Full" line on the side. (See page 10)
2. Check the pre-motor filter at least once a
month and clean or replace as needed.
To access the pre-motor filter, remove the Easy
Empty dirt tank from the vacuum base and push
the lid release button located on the carry
handle. Remove the foam filter from the filter
tray. On models 8531 and 7636 Series, a second
small carbon filter is included here. Replace the
second small, black odor-absorbing carbon filter
as needed.
NOTE: Black Carbon Filter is NOT washable.
3. The post-motor filter assists in the filtration
process to return clean air to the room. Replace
the post-motor filter every three to six months.
To access the post-motor filter, remove the
filter tray located below the Easy Empty dirt
tank. When the filter becomes dirty, push the
filter through the bottom of the tray to clean or
replace the filter.
NOTE: The pleated post-motor filter may NOT
be washed with water or detergent. If dust and/
or debris accumulates on the filter, gently tap
the filter on the side of a garbage container.
Note: More frequent filter cleaning or replac-
ing may be necessary if you are vacuuming
new carpet, fine dust, or have allergy concerns.
Follow the instructions on the following pages
to perform these simple maintenance steps.
AWARNING
Toreducetheriskofelectricshock,turnpowerswitchoff
anddisconnectpolarizedplugfromelectricaloutletbefore
performingmaintenanceortroubleshootingchecks,
washable
filter
Lid Release
Button
Post-Motor
Filter Tray
fitter
NOTICE
Whilevacuuming,certaincarpetsandlowhumidity
conditionsmaygeneratesmallstaticdischarges,The
dischargesareentirelyharmlessandarenotassociated
inanywaywiththemainpowersupply.
www.BISSELL._

Tank
_nk needs to be emptied when the dirt
"Full" line on the side of the tank.
cleaner from electrical outlet.
the Easy Empty dirt tank from the
by pushing the tank release button.
'the dirt tank over a garbage container.
bottom lid release button on the back
dirt tank to empty dirt.
Jnt the Easy Empty dirt tank back on the
base.
tank may be washed in warm
with a mild detergent, Make sure it is
!before replacing,
2. 3.
_1the pre-motor filter and inner cyclone
only genuine BISSELL replacement filters
in your BISSELL CleanView vacuum.
1. Unplug the cleaner from electrical outlet.
2. a. Remove the Easy Empty dirt tank and
locate the pre-motor filter as described on
the previous page.
b. Remove the foam filter from the filter
tray. In models 7636 and 8531 Series, a
second carbon filter is included in here.
The filter tray is fixed in-place, but may be
removed for cleaning by unscrewing 3,
the tray. The foam filter and tray may be
hand washed in warm water with a mild
detergent, if desired. Rinse well, then air
dry thoroughly before replacing the filter.
Make sure all components are completely
dry before replacing. A second black odor-
absorbing filter can also be found here.
Replace this when needed.
NOTE: Black Carbon Filter is NOT washable,
3. The inner cyclone may also be removed for
cleaning. With the bottom of Easy Empty dirt
tank open, reach up into the dirt cup and grasp
the cyclone. Twist the cyclone clockwise to
unlock and pull straight down to remove. Use
the Lock and Unlock Icons on the tank to help
guide the cyclone back in and lock it correctly. It
B important to lock the cyclone back in correctly
_sit will impact performance and separation.
le inner cyclone and dirt cup may be wiped
with a damp cloth. Make sure all parts are
2b.
AWARNING
Donotoperatecleanerwithdamporwetfiltersor
withoutallfiltersinplace.
NOTICE
Donotplacethedirttankorotherproductcomponents
inthedishwasher.Handwashonly.

Replacin_l the post-motor filter
Use only a genuine BISSELL replacement
post-motor filter in your BISSELL CleanView
vacuum.
1. Unplug the cleaner from electrical outlet.
2. The post-motor filter assists in the filtration
process to return clean air to the room. Replace
the post-motor filter every three to six months.
To access the post-motor filter, remove the
filter tray located below the Easy Empty dirt
tank. When the filter becomes dirty, push the
filter through the bottom of the tray to clean or
replace the filter.
NOTE: The pleated post-motor filter may NOT
be washed with water or detergent. If dust and/
or debris accumulates on the filter, gently tap
the filter on the side of a garbage container.
2.
Post-Motor
Filter i
Checkin_l rotatin_l floor brush and drive belt
You should check your vacuum cleaner's rotat-
ing floor brush and drive belt regularly for wear Brush Cover
or damage. You should also clean the brush and 3.
brush ends of strings, hair and carpet fibers.
These can wrap around the brush and hamper
its ability to effectively clean your carpet. Also
remove any debris that has accumulated under
the brush cover.
1. Unplug cleaner from electrical outlet.
2. Place handle in low position and turn vacuum
cleaner over so bottom side is up.
3. Remove the seven screws with a Phillips
head screwdriver. Lift the brush cover off.
4. Grasp rotating floor brush at both ends
and lift straight out of the vacuum foot. Slip
off the belt.
5. Clean strings, hair and other debris from
rotating floor brush, paying particular attention
to brush ends.
6. Clean strings, hair and other debris from
motor pulley and drive belt areas.
7. Check drive belt carefully for wear, cuts
or stressed areas, and replace if necessary
(see instructions on following page).
8. Check air passageway for obstructions.
Remove debris from this area.
4.
Motor
Pulle'
8.
Air
Passageway
www.BISSELL.com 800,237.7691 11

Replace drive belt
Use only a genuine BISSELL style 9 replacement
belt (#203-1093) in your BISSELL CleanView
vacuum.
1. Unplug cleaner from electrical outlet.
2. With rotating floor brush removed from
vacuum cleaner (steps 1-4 of Check rotating
floor brush and drive belt), grasp old drive
belt and remove from motor pulley. Discard
old drive belt.
3. Place new drive belt over motor pulley and
stretch other end over rotating floor brush in
the space between the bristles.
4. Place ends of rotating floor brush down
into slots on sides as shown.
5. Turn rotating floor brush by hand several
times in the direction of motor pulley. If
properly installed, drive belt will center itself
on rotating brush.
6. Reposition the brush cover and screw
all seven screws back into place.
Clearin_l a clo_l
Low suction or poor pickup may be due to
a clog in the vacuum cleaner. If you notice a
change in the sound of the motor or a reduction
in the spinning action of the dirt or brush roll,
check for clogs.
1. Unplug cleaner from electrical outlet.
2. Remove Easy Empty dirt tank from vacuum
base and empty dirt and debris.
3. Remove inner cyclone from Easy Empty dirt
tank (see page 10) and check for debris build-up
or clogs in the upper tank.
4. Check the suction inlet for a clog.
5. Grasp the hose wand to separate from the
hose wand base. Check for a clog in the base,
the wand or within the hose.
6. Remove the screw attaching the hose wand
base to the vacuum. Straighten the hose wand
base and check for clogs with a long, narrow
object such as a broom stick. Do not use sharp
objects like a clothes hanger, as these may
puncture the hose.
7. If the clog persists, follow the instructions for
Checking the rotating floor brush on page 11and
inspect the air passageway for obstructions.
AWARNING
Toreducetheriskofelectricshock,turnpowerswitchoff
anddisconnectpolarizedplugfromelectricaloutletbefore
performingmaintenance0rtr0ublesh00tingchecks.
4.
Motor
Pulley
AWARNING
Toreducetheriskofinjuryfrommovingparts,turn
offvacuumcleaneranddisconnectPowerPlugfrom
electricaloutlet.
6.
www, BISSELL,com _r 800,237,7691
12

Problem
Vacuum
cleaner won't
rum on
Vacuum
cleaner won't
pick up dirt
Possible causes
Power cord not plugged in
Blown fuse/tripped breaker
Remedies
Check electrical plug
Check/replace fuse or reset
Incorrect height adjustment
Hose not attached to suction
opening
Crack or hole in hose
Adjust powerfoot to correct hei!
Grasp the hose wand and firmly
into the hose wand base
Check hose and replace if
Broken or worn drive belt Replace drive belt, see page 11
Rotating floor brush bristles worn Replace brush
Rotating floor brush jammed
Clog in vacuum
Dirt tank full
Remove brush and clean debris
brush ends, see page 11
Follow instructions on page 12 for
clearing clogs
Empty dirt tank
Dirt tank or upper tank not
installed properly
Filters are dirty
Position correctly and lock in place
Tool won't Dirt tank full Empty dirt tank
pick up . . .
D_rt tank or upper tank not Pos_t_on correctly and lock _nplace
installed properly
Filters are dirty Check and clean or replace pre-motor
./ and post-motor filters see pages 9, 10
Vacuum cleaner Incorrect height adjustment lust powerfoot to correct
Visible dirt
escaping from
cleaner
Cord will
not retract
Dirt tank full
Filters missing or installed
incorrectly
Knotted or twisted
height setting
Empty dirt tank
Check pre-motor and post-motor
filters for correct installation
Follow instructions on page 8
Please do
not return
this product
to the store.
Other maintenance or service not included in the manual
performed by an authorized service representative.
Thank you for selecting a BISSELL product.
For any questions or concerns,
be of service. Contact us directl
www.BISSELL._

TheseitemsareavailableforyourBISSELLCteanViewVacuums.
Call 1-800-237-7691 or visit www.bissell.com
PART # PART NAME
]60-0159 BrushRoll(]3.5")
(3583,3247Series)
]60-]503 BrushRoll
(IS",7636Series)
]604504 BrushRoll
(]5",853]Series)
i.........................................
]604506 BrushRolldS")
(2970Series)
]215 Febmze®Post-MotorFilter*
(FitsallCleanViewvacuum9
PART NAME
2034093 Style9DriveBelt
(2-Pack)
1217
.............................................l
onepre-motorfilterand
onepost-motorfilter)
PetFilterPack(includesone
washablefoampro-motorfilter,
oneodor-absorbingcarbonfilter,
andonepost-motorfilter)
(7636&8531Serie9
These items are available for your BISSELL CleanView Vacuums.
Call 1-800-237-7691 or visit www.bissetLcom
14
]60q510
203-2666
2034056
TurboEraserPetTool
(7636&853]Serie©
ExtensionWand
(H",3583,7636,3247Series)
CrevkeTool
2034%7 BustingBrush
ExtensionWand
B",35835,2970,853]Series)
PetHairCornerTool
(7636Series)
*Febreze_andrelatedtrademarksareownedbyTheProcter&GambleCompanv,Cincinnati,Ohio,andusedunderlicenseb
www.BISSELhcom _r 800.237.7691
,BISSELLHomecare,Inc.

Thiswarrantygivesyouspecificlegal_lts, andyoumayalso
haveotherrightswhichmayvaryfromstatetostate.Ifyouneed
additionalinstructionregardingthiswarrantyorhavequestions
regardingwhatitmaycover,pleasecontactBISSELLConsumerCare
byE-mail,telephone,orregularmailasdescribedbelow.
Limited Three-Year Warranty
Subjecttothe*EXCEPTIONSANDEXCLUSIONSidentifiedbelow,upon
receiptoftheproductBISSELLwillrepairorreplace(withnewor
remanufacturedcomponentsorproducts),atBISSELL'soption,free
ofchargefromthedateofpurchasebytheoriginalpurchaser,for
threeyearsanydefectiveormalfunctioningpart.
Seeinformationon"IfyourBISSELLproductshouldrequireservice".
Thiswarrantyappliestoproductusedforpersonal,andnotcommercial
orrentalservice.Thiswarrantydoesnotapplytofansorroutine
maintenancecomponentssuchasfilters,belts,orbrushes,Damageor
malfunctioncausedbynegligence,abuse,neglect,unauthorizedrepair,
oranyotherusenotinaccordancewiththeUser'sGuideisnotcovered,
BISSELLISNOTLIABLEFORINCIDENTALORCONSEQUENTIALDAMAGES
OFANYNATUREASSOCIATEDWITHTHEUSEOFTHISPRODUCT,BISSELL'S
LIABILIIYWILLNOTEXCEEDTHEPURCHASEPRICEOFTHEPRODUCT.
Somestatesdo not allowthe exclusionor limita-
tionof incidentalorconsequentialdamages,sothe
abovelimitationor exclusionmay notapplyto you.
*EXCEPTIONS AND EXCLUSIONS FROM
THE TERMS OF THE LIMITED WARRANTY
THISWARRANTYISEXCLUSIVEANDINLIEUOFANYOTHER
WARRANTIESEITHERORALORWRITTEN.ANYIMPLIEDWARRANTIES
WHICHMAYARISEBYOPERATIONOFLAW,INCLUDINGTHEIMPLIED
WARRANTIESOFMERCHANTABILITYANDFITNESSFORAPARTICULAR
PURPOSE,ARELIMITEDTOTHETHREEYEARDURATIONFROMTHEDATE
OFPURCHASEASDESCRIBEDABOVE.
Somestatesdonotallowlimitationsonhowlonganimplied
warrantylastsotheabovelimitationmaynotapplytoyou.
NOTE: Please keep your original sales
receipt. It provides proof of date of
purchase in the event of a warranty claim.
If your BISSELL product
require service:
VisitBISSELL.com
BISSELLAuthorizedServiceCenterinyourarea,
Ifyouneedinformationaboutrepairsorreplacementp
havequestionsaboutyourwarranty,contact
Website or E-mail:
www.BISSELL.com
Or Call:
BISSELL Consumer Care
1-800-237-7691
Monday - Friday 8am - lOpm ET
Saturday 9am - 8pm ET
Sunday lOam - 7pm ET
Or Write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids, HI 49501
ATTN: Consumer Care
www.BISSELL._

BISSELL Rewards Points
Automatically earn points for
discounts and free shipping on
future purchases.
Faster Service
Supplying your information now
saves you time should you need
to contact us with questions
regarding your product.
Product Support
Reminders and Alerts
We'll contact you with any
important product maintenance
reminders and alerts.
Special Promotions
Optional: Register your email
to receive notice of offers,
contests, cleaning tips and more!
For information about repairs or replacement parts, or questions about your warranty:
Call:
BISSELL Consumer Care
1-800-237-7691
Monday -Friday 8 am -10 pm ET
Saturday 9am - 8 pm ET
Sunday lOam - 7pm ET
Write:
BISSELL Homecare, Inc,
PO Box 3606
Grand Rapids IHI 49501
ATTN: Consumer Care
Visit the BISSELL website: www.BISSELL.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number:
Please record your Purchase Date:
NOTE: Please keep your original sales receipt. It provides proof of purchase
date in the event of a warranty claim, See Warranty on page 15 for details,
16
'c2013BISSELLH0me(are.1no
GrandRapids,Michigan
Allrightsreserved.PrintedinChina
PartNumber160_587Rev7/13
Visitourwebsiteat:www'.%SEtL_0m