Bissell POWER GROOM PET 6.70E+03 User manual

USER'S GUIDE
67E2 SERIES
Earn BISSELL Rewards!
Register your
product today!
See details on
back page
2Thank You
Safety Instructions
Product View
Assembly
Operations
Maintenance and Care
Troubleshooting
Replacement Parts
3
4
5
6-10
11-14
15-16
17
20
Accessories
Product Registration
Warranty
Consumer Services
18
20
19

www.bissell.com 800.237.7691
Thanks for buying a BISSELL PowerGroom® Pet Canister Vacuum
We’re glad you purchased a BISSELL PowerGroom Pet canister
vacuum. Everything we know about floor care went into the design
and construction of this complete, high-tech home cleaning system.
Your PowerGroom Pet canister vacuum is well made, and we back
it with a limited one year warranty. We also stand behind it with
a knowledgeable, dedicated Consumer Services department, so,
should you ever have a problem, you’ll receive fast, considerate
assistance.
My great-grandfather invented the floor sweeper in 1876. Today,
BISSELL is a global leader in the design, manufacture, and
service of high quality homecare products like your PowerGroom
Pet Canister vacuum.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
Chairman, President & CEO
2

www.bissell.com 800.237.7691
IMPORTANT SAFETY INSTRUCTIONS
3
When using an electrical appliance,
basic precautions should be observed,
including the following:
READ ALL
INSTRUCTIONS
BEFORE USING YOUR
CANISTER VACUUM.
Always connect to a polarized outlet
(left slot is wider than right). Unplug
from outlet when not in use and before
conducting maintenance.
WARNING: To
reduce the risk of fire,
electric shock, or injury:
■ Do not leave cleaner when it is
plugged in.
■ Unplug from outlet when not in use
and before servicing.
■ Do not use with damaged cord or plug.
■ To unplug grasp plug not cord.
■ Do not pull or carry by cord, use cord as
a handle, close door on cord, pull cord
around sharp corners, run cleaner over
cord, or expose cord to heated surfaces.
■ Hold plug when rewinding the cord
onto the reel. Do not allow the plug
to whip when rewinding.
■ Do not use cleaner if it has been
dropped, damaged, left outdoors or
dropped into water. Have it repaired
at an Authorized Service Center.
■ Do not allow children to use as a toy.
■ Do not use outdoors or on wet surfaces.
■ Do not handle cleaner or plug with
wet hands.
■ Do not put any object into openings, use
with blocked opening, or restrict air flow.
■ Do not use without dust bag and/or
filters in place.
■ Do not allow hair, loose clothing, fingers
or body parts to get near openings or
floor brush in the appliance.
■ Do not pick up hot coals, cigarette
butts, matches or any hot, smoking,
or burning objects.
■ Do not pick up hard or sharp objects
such as glass, nails, screws, coins, etc.
■ Do not pick up flammable or combus-
tible materials (lighter fluid, gasoline,
kerosene, etc.) or use in the presence
of explosive liquids or vapor.
■ Do not unplug by pulling on cord.
■ Do not pick up toxic material (chlorine
bleach, ammonia, drain cleaner, etc.).
■ Do not use in an enclosed space filled
with vapors given off by oil base paint,
paint thinner, some moth proofing
substances, flammable dust, or other
explosive or toxic vapors.
■ Do not use for any purpose other
than described in this User’s Guide.
■ Always turn off this appliance before con-
necting or disconnecting vacuum hose.
■ Use only manufacturer’s
recommended attachments.
■ Use only on dry, indoor surfaces.
■ Keep openings free of dust, lint, hair, etc.
■ Keep appliance on a level surface.
■ Turn off all controls before plugging
or unplugging cleaner.
■ Be extra careful when cleaning stairs.
■ Close attention is necessary when
used by or near children.
SAVE THESE
INSTRUCTIONS
FOR FUTURE USE
THIS APPLIANCE
HAS A POLARIZED
PLUG.
To reduce the risk of electric shock,
this appliance has a polarized plug (one
blade is wider than the other). This plug
will fit in a polarized outlet only one
way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does
not fit, contact a qualified electrician to
install a proper outlet. Do not change
the plug in any way.
This model is for household use only.

www.bissell.com 800.237.7691
4
Variable Suction
Power Control
Brush Roll
On/Off
Telescoping
Extension Wand
Flex Hose
Swivel Hose
Powerhead
Handle
Power Button Post-Motor
HEPA Media
Filter
Bag Change
Indicator
Automatic
Cord Rewind
Button
Product view
Dusting Brush
Floor Brush Tool HolderCrevice ToolUpholstery
Tool
BareFloor Tool
Pet Tool Adaptor Accessory Storage Bag
Wide Pet
TurboBrush®
Pet Contour
Tool®

www.bissell.com 800.237.7691
Assembly
1. Connect swivel hose by squeezing both
locking buttons and inserting it into the
suction opening on the canister. Once
the swivel hose is inserted in the suction
opening, release the locking buttons.
2 . Plug the cord from the hose into the slot
on the lower left front of canister.
3. Connect and plug-in telescoping
extension wand to the handle end of the
flex hose.
4. Connect the powerhead onto the tele-
scoping extension wand.
5. Attach the tool holder to the telescoping
extension wand and insert the tools into
the holder.
6. To extend the telescopic tube, push the
black release button and then pull the
tube to the desired length.
NOTE: Shorten length of telescopic
tube for storage.
7. To store the barefloor tool, insert the stor-
age clip into the storage slot on the rear
of the vacuum or on the back of the unit
when in an upright position.
WARNING:
Plastic film can be
dangerous. To avoid danger
of suffocation, keep away
from babies and children.
1.
7.
5.
5

www.bissell.com 800.237.7691
Operations
6
Special tools
Your BISSELL PowerGroom Pet is not
only a powerful carpet and rug
vacuum cleaner, it’s also a versatile
bare floor vacuum cleaner and above
floor vacuum cleaner when you select
one of the special tools.
Powerhead:
The PowerGroom Pet comes with the
powerhead for your regular use. The
powerhead has many features, including:
1. A motorized, rotating brush that can be
turned on/off by a switch on the handle
so you can protect your bare floors.
2. Six height adjustments so you can vacuum
from non-carpet to carpeted areas with ease.
3. Variable suction control which can be con-
trolled on a switch located on the handle.
BareFloor tool:
Use to vacuum carpets, rugs and bare
floors. Swivel head turns to get into
tight spaces and fits under cabinets.
1. To vacuum carpets and rugs, push the
brush switch to the carpet position .
This will pull the brushes up into the floor
nozzle.
2. To vacuum bare floors, push the brush
switch to the bare floor position .
This will extend the brushes down from the
floor nozzle.
Pet Tool Adapter:
The Pet Tool Adapter must be attached
to the handle end of the flex hose to
use the Pet Contour Tool and the Wide
Pet TurboBrush. The narrow end of the
adapter attaches to the handle end of
the flex hose and the wide end of the
adapter attaches to the pet tool of your
choice. The adapter should fit snugly
to the hose and pet tool without using
excessive force.
Tip:
Before cleaning under low furniture,
check area first for objects that might
harm the unit or block the hose.
Tip:
Hair, string and small objects can block
the hose and tools. Check them occa-
sionally for obstructions.
1.
2.
Brush
Down
Brush
Up

Special tools continued
Pet Contour Tool:
Use to reach into corners and edges
on stairs, as well as armrests and
other curved surfaces. The tool can be
flipped to use in any direction.
Wide Pet TurboBrush:
Use rotating brush action for small,
flat areas such as cushions and beds.
Floor brush:
Ideal for cleaning edges on bare floor.
Dusting brush:
Use the dusting brush to dust furni-
ture, blinds, books, lamps, shelves
and baseboards.
Upholstery tool:
Use the upholstery tool to clean cur-
tains, draperies, cushions and fabrics.
Crevice tool:
Use the crevice tool in tight, narrow
spaces.
Power cord
The power cord is located at the
rear of the vacuum. Gently pull out
the power cord, watching for the
yellow line. Stop pulling the power
cord once the yellow line is visible.
There is also a red line, which indi-
cates the end of the usable cord. Do
not pull the power cord out beyond
the red line.
Automatic cord rewind
Your vacuum is equipped with an
automatic cord rewind. When
cleaning is finished, press the power
button OFF and grasp the plug to
disconnect from the electrical outlet.
Hold the plug and press the
automatic cord rewind button to
rewind the cord automatically.
www.bissell.com 800.237.7691
7
Operations
CAUTION:
Be careful to avoid
injury as cord retracts
very quickly.
Automatic
Cord
Rewind
Button

www.bissell.com 800.237.7691
Operations
www.bissell.com 800.237.7691
8
Power button
Turn the power on or off by pressing
lightly downward on the power button
( ).
Motorized powerhead
Set the power switch on the handle to 1
for rotating brush or 0 to turn rotating
brush off.
NOTE: The power brush will auto-
matically turn off if the telescopic
tube is in an upright position to pro-
tect your carpet from potential dam-
age caused by the rotation of the
power brush.
NOTE: The power brush will auto-
matically turn off if the rotator bar
is blocked by clogs (hair, cloth, ect.)
for your protection. In that case, turn
off the power head, unplug the vac-
uum, clean the clog, and re-start the
power brush.
Variable suction power control
The variable suction power control is
located on the top of the handle. Slide
the control toward the larger dots for
maximum suction. Slide the control
toward the smaller dots to minimize
suction for lightly soiled areas or
delicate fabrics.
Variable height adjustments
Step on the brush height adjuster
located on the right side of the motor-
ized powerhead to adjust for flooring
type (lowest setting (1)for non-carpet,
indoor areas, highest setting (6) for
plush pile carpet).
Power
Button
CAUTION:
Before using your vacuum,
make sure that the dust bag
and all filters (pre-motor
and post-motor) are in
place. Do not operate your
vacuum without the dust
bag and filters.
Variable
Suction
Control
PowerBrush
On/Off

www.bissell.com 800.237.7691
9
Operations
Handle position
Press the handle release pedal,
located in the middle of the
motorized powerhead, with your
foot to place your vacuum into
one of the three cleaning posi-
tions.
1. Upright – For storage and above
floor cleaning with tools.
2. Normal Cleaning – Press handle
release pedal once. Position used
for most household floor cleaning
tasks.
3. Low Cleaning – With the vacuum
in normal cleaning position, press
handle release pedal again. Use for
reaching under low furniture such as
tables, chairs or beds.
Bag change indicator
The bag change indicator is located
between the power button and the
automatic cord rewind button. If the
bag change indicator turns orange
while you are vacuuming, the dust
bag needs to be replaced. The dust
bag may appear to be full or only
partially full depending upon the
type of debris picked up. Fine
particles can block the airflow
in the dust bag and reduce suc-
tion before the dust bag is full. If
the bag change indicator remains
orange, even after changing the
dust bag, turn the vacuum off and
check for a clog in the hose or tools.
Tip:
Before cleaning under low furni-
ture, check area first for objects
that might harm the unit or block
the vacuum hose.
1.
2.
3.
Bag Change
Indicator

www.bissell.com 800.237.7691
Operations
10
Dust bag replacement
1. Unplug the vacuum from electrical outlet.
2. Disconnect hose
3. Open the dust bag compartment by
lifting up on the latch on the door on
the front of the vacuum.
4. Lift out the dust bag holder and dust bag.
5. Release the dust bag from the holder
by pressing the dust bag holder clip
and pulling the dust bag out of the
holder. Discard the used dust bag.
6. Slide the new dust bag into the
holder by inserting the dust bag into
the tabs located at the bottom of
the holder. Then press the dust bag
holder clip, insert the dust bag and
release the dust bag holder clip to
hold the dust bag in place.
7. Place holder and new dust bag
back into the dust bag compartment,
making sure the entire bag is tucked
in below the seal gasket.
8. Close dust bag compartment door
and press down gently until it locks
into place.
NOTE: The dust bag compart-
ment door will not close with-
out the dust bag in place.
9. Reconnect hose.
3.
4.
5
WARNING:
To reduce the risk of electric
shock, turn power switch OFF
and disconnect plug from
electrical outlet before
performing maintenance or
troubleshooting checks.

www.bissell.com 800.237.7691
11
Maintenance and care
Cleaning the pre-motor filter
The pre-motor filter protects the
motor from dirt and dust par-
ticles.
1. Unplug the vacuum from electrical
outlet.
2. Disconnect hose
3. Open the dust bag compartment by
lifting up on the latch on the door at
the front of the vacuum. Lift out the
dust bag holder and dust bag.
4. Remove the filter frame from the filter
holder by grasping the lip of the
frame and pulling up.
5. Remove the filter from the filter frame
and clean by hand washing in
warm water. A mild detergent can
be used if desired. Allow the filter to
air dry thoroughly before replacing.
6. Place the filter back into the filter frame
and replace back into the filter holder.
NOTE: The filter frame should
be placed so the protective
frame is visible.
7. Place dust bag holder and dust bag
into the dust bag compartment, mak-
ing sure the entire bag is tucked in
below the seal gasket.
8. Close dust bag compartment door
and press down gently until it locks
into place.
9. Reconnect hose.
Washable Pre-
Motor Filter
NOTICE:
This product is intended for household
use only and not for commercial or
industrial use. Vacuuming of dust
from products like plaster, concrete
or ashes will damage the motor and
void the warranty.
Tip:
For maximum cleaning perfor-
mance, check the filters often and
clean or replace if necessary.
WARNING:
Do not operate cleaner with
damp or wet filters or without
all filters in place.
3.

www.bissell.com 800.237.7691
Maintenance and care
12
The post-motor HEPA media
filter assists in the filtration
process to return clean air to
the room.
1. Unplug the vacuum from electrical
outlet.
2. Remove the filter door (located on
the rear of the vacuum) by pulling
up on the filter door latch.
3. Remove the post-motor HEPA media
filter by grasping the lip of the filter
frame and pulling up.
4. Replace the post-motor HEPA
media filter with a new filter.
NOTE: The post-motor filter is
a white, pleated HEPA media
filter. This filter is NOT wash-
able and must be replaced
when it becomes dirty.
NOTE: The HEPA media filter
should not be touched, when
handling be sure to only touch
the frame.
5. Replace the filter door by inserting
the two tabs at the top of the filter
door and pushing down on the
bottom of the filter door.
Replacing the post-motor HEPA media filter
Post-Motor
HEPA Media
Filter
2.
3.

www.bissell.com 800.237.7691
13
Maintenance and care
The Wide Pet TurboBrush
should be checked regularly
for clogs or debris wrapping
around the brush.
1. Turn vacuum OFF ( ) unplug the
vacuum from electrical outlet.
2. If a clog is present or debris is
visible, turn the collar on the neck
of the Wide Pet TurboBrush counter-
clockwise to the unlocked position
to remove the faceplate and clear
any obstructions.
3. To clean debris from the brush,
remove the brush from the drive belt
and clean debris.
4. Reposition the drive belt on the
brush. Place the ends of the brush
in the slots on the sides. Reposition
the faceplate and turn the collar
clockwise to the locked position.
Maintaining the Wide Pet TurboBrush

www.bissell.com 800.237.7691
Maintenance and care
14
The brush can usually be cleaned
without removal from the vacuum. If
there is an excessive amount of hair
and debris, however, it is best to
remove the brush.
1. Unplug the vacuum.
2. Lay the motorized powerhead for-
ward on the floor.
3. Locate the locking screws (2) on the
bottom of the powerfoot. Using a
Phillips head screwdriver, remove the
screws. Lift off the brush cover. Grasp
the brush firmly, and pull it out.
4. Clean debris from brush. Lint, carpet
pile, and hair can be removed with
a pair of scissors. If brush bristles are
worn or missing, replace brush.
5. Slide belt over brush onto the belt
track. Slide belt over the motor pulley.
To reinstall brush, slide square ends of
brush into grooves, beginning with the
belt side. The drive belt should have
room to rotate within the belt channel.
Make sure drive belt is looped over
roller and not twisted. Inspect belt
action by rolling the brush with the
palm of your hand.
6. Reattach brush cover to powerhead
with (2) screws.
Replacing the drive belt
1. Follow steps 1, 2 and 3 from the
Cleaning the motorized powerhead
section.
2. Remove old belt from brush.
3. Attach new belt, aligning as indicate
in steps 5 and 6 from Cleaning the
motorized power head section.
Cleaning the motorized powerhead
3.
5.

www.bissell.com 800.237.7691
15
Troubleshooting
Vacuum cleaner won’t run
Possible causes Remedies
1. Vacuum cleaner is not plugged in 1. Check electrical plug
2. Power button is not pressed down 2. Press power button down
Vacuum cleaner won’t pick up or low suction
Possible causes Remedies
1. Tools, flex hose and/or telescoping 1. Remove each part and check for blockages
extension wand are blocked
2. Filters are dirty 2. Check and clean or replace pre-motor
and post-motor filters
3. Dust bag is full 3. Replace with new dust bag
4. Swivel hose not securely 4. Make sure swivel hose is locked into
attached to suction opening suction opening
5. Crack or hole in flex hose 5. Check hose and replace if needed
6. Air flow regulator or variable suction power 6. Change to closed or maximum setting
control is set to open or minimum setting
Visible dust escaping from vacuum
Possible causes Remedies
1. Dust bag is full 1. Replace with new dust bag
2. Filters missing or installed incorrectly 2. Check pre-motor and post-motor filter for
correct installation
3. Filters are dirty 3. Check and clean or replace pre-motor
and post-motor filters
4. Flex hose is blocked 4. Remove hose and check for
blockages
5. Swivel hose not securely 5. Make sure swivel hose is locked into
attached to suction opening suction opening
6. Crack or hole in flex hose 6. Check hose and replace if needed
WARNING:
To reduce the risk of electric
shock, turn power OFF and
disconnect plug from electrical
outlet before performing mainte-
nance or troubleshooting.

www.bissell.com 800.237.7691
Troubleshooting
16
Other maintenance or service not included in the manual should be
performed by an authorized service representative.
Thank you for selecting a BISSELL product.
Please do not return this product to the store.
For any questions or concerns, BISSELL is happy to be of
service. Contact us directly at 1-800-237-7691.

www.bissell.com 800.237.7691
17
Replacement parts - BISSELL vacuum
Item Part No. Part Name
1 203-7270 Dust Bag (3pk)
2 203-7268 Pre-Motor Filter
3 203-7269 Post-Motor HEPA Media Filter
4 203-7315 Hose Grip with Powercord
5 203-7274 Tool Holder
1234
5

www.bissell.com 800.237.7691
Accessories
18
Item Part No. Part Name
1 203-7309 Barefloor Tool
2 203-7310 Floor Brush
3 203-7314 Extension Wand with Power Cord
4 203-7273 Upholstery Tool
5 203-7272 Dusting Brush
6 203-7271 Crevice Tool
7 203-7279 Pet Tool Adaptor
8 203-1291 Pet Contour Tool
9 203-1290 Wide Pet TurboBrush
10 203-7278 Accessory Bag
2
6
10
3
7
4
8
1
5
9

www.bissell.com 800.237.7691
19
Warranty - BISSELL PowerGroom Pet Compact Vacuum
This warranty gives you specific legal rights, and you may also have other rights which may
vary from state to state. If you need additional instruction regarding this warranty or have
questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail,
telephone, or regular mail as described below.
Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product
BISSELL Homecare, Inc. will repair or replace (with new or remanufactured components or
products), at BISSELL’s option, free of charge from the date of purchase by the original
purchaser, for one year any defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental service. This
warranty does not apply to fans or routine maintenance components such as filters, belts, or
brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any
other use not in accordance with the User's Guide is not covered.
If your BISSELL product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your
area.
If you need information about repairs or replacement parts, or if you have questions about
your warranty, contact BISSELL Consumer Services.
Website or E-mail:
www.bissell.com
Use the “Customer Support” tab.
Or Call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. - 10 p.m. ET
Saturday 9 a.m. - 8 p.m. ET
Or Write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids, MI 49501
ATTN: Consumer Services
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT
EXCEED THE PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR
WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED
ABOVE.
Some states do not allow limitations on how long an implied warranty last so the
above limitation may not apply to you.

©2010 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 110-4233
Rev 4/10
Visit our website at:
www.bissell.com
For information about repairs or replacement parts, or questions about your warranty, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. — 10 p.m. ET
Saturday 9 a.m. — 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It
provides proof of purchase date in the event of a
warranty claim. See Warranty on page 19 for details.
BISSELL consumer services
www.bissell.com 800.237.7691
20
Registering is quick, easy and offers you benefits over the lifetime of your product.
You’ll receive:
BISSELL Rewards Points
Automatically earn points for discounts and free shipping on future purchases.
Faster Service
Supplying your information now saves you time should you need to contact us with
questions regarding your product.
Product Support Reminders and Alerts
We’ll contact you with any important product maintenance reminders and alerts.
Special Promotions
Optional: Register your email to receive notice of offers, contests, cleaning tips and more!
Visit www.bissell.com/registration now!
Don't forget to register your product!