Bissell ProHeat 7950 SERIES User manual

BISSELL SELF PROPELLED UDC - MODEL 7950
Highlights of the new model
The main differences between the self propelled UDC and the
standard UDC occurs in the Upper and Lower Handle Assemblies.
The Lower Handle Assembly contains a Transmission/Motor
Assembly with Belt Drtve, Rectifier/Terminal Board, and Neutral
Knob. The transmission motor is 110 volt DC.
The Neutral Knob-is the mechanism used to engage and disengage
the transmission for use. To move the unit without the use of the
transmission, the Neutral Knob must be in the "OFF" position.
The Lower Handle also contains the Heater and Trigger Valve
Assembly. The Trigger Valve Assembly has tubes that are of
different length than other Bissell UDC models. The Trigger Valve
Assembly is not interchangeable with standard models (non self
propelled).
The Upper Handle Assembly contains the "ON" - "OFF" switches for
both the unit's Power and the Heater. If the need arises to change
out the Lower Handle Assembly wire harness, it is recommended that
the Upper Handle Harness be changed out also. The two wiring
harnesses are supplied as asingle replacement kit.
The wheels are new and are not interchangeable with other models
The tube routing and components have remained the same in the
foot assembly. The pump, motor, base, brush assembly, etc. are the
same as in the standard models.
The Tool Caddy on the 7950 is different than on the standard models.
BISSF_LL - 7/03

BISSELL SELF PROPELLED UDC - MODEL 7950
LOWER HANDLE ASSEMBLY
The 7950 Lower Handle can be disassembled without removing the Tool Caddy. You
can either leave the hose wrapped and work around it, or unwrap the hose for
unobstructed access to the screws.
1. Remove (2) screws located near the bottom of the Tool Caddy (just above the tank)
on the back of the unit. You will need a long barreled Phillips screw driver- 10"
long
2. Remove (2) screws located near the top of the Tool Caddy on the back of the
utfit.
upper
3. Lift Lower Handle Front off Lower Handle Back - there are no wires connected to
the Lower Handle Front.
7/24/03 1/5

Circuitboard
BISSELL SELF PROPELLED UDC - MODEL 7950
LOWER HANDLE COMPONENTS
Junction - Upper Handle Harness
to Lower Handle
Transmission Motor (DC) Tran Transmission Linkage
* If the Transmission Linkage is removed, upon reasseanbly make sure to hook the Linkage over the
Control Ann with the hole in the Linkage covering the locating tab on the Control Arm
Transmission Linkage Ann
7/24/03
'Transmission. Control Arm locating tab
2/5

BISSELL SELF PROPELLED UDC - MODEL 7950
LOWER HANDLE COMPONENTS
NEUTRAL KNOB -controls the engagement of the transmission. In the "ON" position it aa]ows
the transmission to engage., In reassembly make sure washer is at the end of the s
IDLER ARM ASSEMBLY - Contains drive belt
7/24/03 3/5

BISSELL SELF PROPELLED UDC - MODEL 7950
LOWER HANDLE COMPONENTS
HEATER LIGHT - The Heater Light can be removed by gently pul]Jng the light
case Ul_
TRIGGER VALVE ALIGNMENT AND CLAMPS - The trigger valve needs to have the clamps
orientated so the wings face
7124103 415

BISSELL SELF PROPELLED UDC - MODEL 7950
UPPER HANDLE ASSEMBLY
The Upper Handle Assembly contains the ON/OFF switch, Heater Control switch, and the Wiring
Harness that connects to flae Lowe_ Handle Assembly Harness.
Switches ON/OFF
UPPER t-IANDLE
7124103 5/5

Upright Deep Cleaner
Model 7950
BISSELL Service Center Dept.
1-800-457-I _09
Fax: 1-800-$I 7-_535
ssued: May 2003
aartner, bissell.com
zoo_

7950
DESCRIPTION
UPPER HANDLE ASSEMBLY
SPRING - PUSH ROD
ROD
TRIGGER
SWITCH - HEATER
SWITCH - POWER
!LOWER HANDLE FRONT
LE_
31RCUIT BOARD
LINKAGE
]-RIGGER VALVE ASSY
LIGHT ASSEMBLY
SUPPORT
70_..
TRANSMISSION
_EMBLY
DRIVE BELT
LOWER HANDLE BACK ASSEMBLY
NEUTRAL KNOB ASSEMBLY
:E RACK ASSEMBLY
TOOL HOLDER
CORD WRAP
WAND CLIP
t_XLE
WHEEL - OVERMOLDED w! GEAR
E-RiNG- WHEEL AXLE
_)VERMDLDED
EXTRUDED GASKET -.136" x 32"
SEAL - OVAL
SHAMPOO BOTTLE ASSY
CAP ASSEMBLY. SHAMPOO BOITLE
AUTOLOAD OVERSEAL
DIVERTER - MED COOL GREY
FLOW IND. ASSY- CAP SP!NNER, ROTO!
DIVERTER GASKET
FLOW INDICATOR BASE
AUTOMIX KNOB GREY
MAIN HOUSING _ BLACK METALLIC
WINDOW NOZZLE ASSY -6ROW BR_u-sH- --
SPRAY TIP
T CONNECTOR
CLEARVIEW WINDOW _02165 .....
&LT
t ASSY- 6 ROW- ORANGE ,_
BRi]SH--6-_f ,,
.,p
BrSSELI.Service Center DeparIrnent
57-1509
_ll.com
DESCRIPTION
&6 ROW ORG BRUSH
CACUUM MOTOR
3ASKET - MOTOR INTAKE
SHORT AIR DUCT
GASKET - SHORT AIR DUCT
BELT COVER - BLACK METALLIC --
MOTOR COVER
MOTOR GASKET
HOSE & GRIP ASSY
AUTOLOAD RECEIVER
HANDLE RELEASE PEDAL
ELEVATOR LEVERS - RT & LT .._
PUMP ABSY
PUMP BELT
TANK ASSY - COMPLETE
TANK TOp ASSY w/HANDLE
TANK HANDLE
BAFFLE &BLADDER ASSY
BAFFLE & FLOAT ASSY
FLOAT ASSY
BLADDER
K/BAFFL_BLADDEPJFLOAT
SCREW_xI_"
MESH BAG
CARPET PROTECTANT SPRAYER ASSY
CARPET PROTECTANT CARTRIDGE 4/CS
I" TOUGH STAIN TOOL
BRUSH FOR 3" TOUGH STAIN TOOL
-RY TOOL
BRUSH FOR 4" UPHOLSTERY TOOL
CREVICE TOOL
USER'S GUIDE
CORDSET 33' 3-WIRE 17CA
WIRE HARNESS - UPPER &LOWER
-#8-1 lx.5"
HARDWARE KIT - #8 x I/2" 6(_p_s) .__
Issued: 06/03
Revi_ed:08105