BJ ADAPTACIONES BJ-231 User manual
BJ-231 BJ ENABLER PHONE
User Guide
BJ-231 BJ ENABLER PHONE
Page 2
1_Description of the device
With this product you can control a hands-free telephone via any of
the BJ System remote controls.
It contains two elements: A hands-free telephone model KERO KET-
37HS, and an enabler belonging to the BJ System, specific to this
telephone (Fig. 1).
Figure 1: BJ Telephone
2_Functionality
Besides the standard functions of a telephone, indicated in its user
guide, you can control the telephone wirelessly via any of the BJ
System remote controls.
In this case, the functions available are as follows:
oMaking calls with automatic dialling of numbers stored in any
of the telephone’s 10 off-line storage systems.
oMaking calls by dialling number by number any telephone
number.
oAnswering calls made to your telephone.
oHanging up a call at any time.
oDialling numbers during a call to carry out control functions
on exchanges or other automatic systems (DTMF), such as
dialling an extension, for example.
BJ System
enabler
Hands-free
telephone
#
9
6
3
0
8
5
2
*
7
4
1
1234567890
1234567890
M10
M9
M8
M7
M6
M5
M4
M3
M2
M1
Teléfono B&J
www.bj-adaptaciones.com
BJ-231
BJ-231 BJ ENABLER PHONE
Page 3
3_Installation
To install the equipment you must make as many connections
from the BJ System enabler (Section 3.1) as connections there
are on the telephone (Section 3.2):
3.1. Installing the BJ System enabler
To install the enabler just connect it to an AC 230V power socket.
The enabler’s connection characteristics are indicated on the
equipment’s label.
3.2. Installing the telephone
To install the telephone follow the device’s User Guide, supplied
with this product. It is important that the telephone’s handle is
correctly fitted to the base of the telephone and the base is
connected to the telephone line.
For proper operation the supply cable supplied with the product
must be connected.
IMPORTANT:
The enabler must be plugged in for the phone to work. Otherwise, the
telephone will be locked. The device’s pilot lamp indicates that the enabler is
connected.
IMPORTANT:
To ensure the numbers stored in the phone’s memory are not deleted if
the line goes down, the 4 rechargeable batteries supplied with the product
should be installed in the compartment at the bottom of the phone. Only
use type AAA 1.5V rechargeable batteries.
Whenever you connect or disconnect the batteries, the phone must be
disconnected from the phone line.
BJ-231 BJ ENABLER PHONE
Page 4
4_Instructions for use
The phone can be used manually in the standard way as
explained in the manufacturer’s user guide.
Alternatively, you can also control it in two other ways: using BJ
System controllers (4.1) and using switches (4.2).
4.1. Control using a BJ System controller
To control the phone using any BJ System remote control, you
just need to program on the remote the codes that make the
enabler activate the phone. Once you have programmed them,
you will be able to access the phone’s functions via the remote.
Below is a list of codes according to the action to be performed:
•Picking and hanging up the phone
To answer a call or end it, you must program the RF code
assigned in to the phone’s “Hands-free” button (consult the
controller’s User Guide to carry out this operation). The code is
given in this table:
When you receive a call and you want to answer it you just need
to activate the cell on the controller that you have just
programmed. You can end or hang up on a call with the same
button.
•Calling a number stored in the phone
To dial a number from the memory, you must first store it in the
phone’s off-line storage. To do this, follow these steps:
1. With the phone not in use and the power supply connected,
dial the number to be memorised.
2. Press the SAVE button.
3. Enter the number (from 0 to 9) corresponding to the
memory position where you wish to store the phone
number.
NOTE: You can save a new number on top of a memory
position already in use, by deleting the existing one.
RF Code
Action
110
Pick up/Hang up the phone
(Hands-free function)
BJ-231 BJ ENABLER PHONE
Page 5
To control the phone from the BJ remote control, you must
program in the different cells of the remote, the RF codes that
allow you to call the memorised numbers.
Below is a list of RF codes that activate the automatic dialling of
the memory positions:
RF Code
Action
90 Call number in memory position 0
91 Call number in memory position 1
92 Call number in memory position 2
93 Call number in memory position 3
94 Call number in memory position 4
95 Call number in memory position 5
96 Call number in memory position 6
97 Call number in memory position 7
98 Call number in memory position 8
99 Call number in memory position 9
Once you have programmed the remote, you just have to press
the corresponding button to execute the option. When the
enabler receives the command, it makes the blue LED indicator
flash three times to indicate that the call is being made. Then the
enabler will pick up the phone and dial the number automatically.
You do not need to pick it up first.
•Call via number by number dialling
To dial a number that is not stored in the phone, you must
program on your BJ System remote control, the RF codes
indicated in the following table, which correspond to the numbers
from 0 to 9. In addition, it has codes assigned to the phone’s
control functions.
BJ-231 BJ ENABLER PHONE
Page 6
RF Code
Action
100 Activate number 0on the phone
101 Activate number 1on the phone
102 Activate number 2on the phone
103 Activate number 3on the phone
104 Activate number 4on the phone
105 Activate number 5on the phone
106 Activate number 6on the phone
107 Activate number 7on the phone
108 Activate number 8on the phone
109 Activate number 9on the phone
111 Activate cell *on the phone
112 Activate cell #on the phone
To enter a number you must first activate the cell on the remote
control, which corresponds to the pick-up and hang-up function.
This will activate the phone’s hands-free function, and you will
hear the dial tone through the loudspeaker.
You can then start to dial the phone number by activating one of
the cells on the remote corresponding to the numbers to be
dialled.
Every time the enabler receives a command, the ON indicator will
be turned off for an instant.
4.2 Control via switch
The enabler for the phone has two sockets for switches that allow
you to control the following functions:
Socket for switch 1 (left) (Figure 2): By activating this socket via
a switch, the phone will be picked up and it will automatically dial
the number stored in off-line memory position 1. If you activate
it again during a call, it will be ended. By activating the socket,
the ON light indicator will flash three times.
Socket for switch 2 (right) (Figure 2): By activating this socket
via a switch, the phone will be hung up or picked up. If it was
hung up it would be picked up and vice versa. By activating the
socket, the ON light indicator will be turned off for an instant.
BJ-231 BJ ENABLER PHONE
Page 7
Figure 2. Enabler’s switch sockets.
5_Maintenance
For the phone’s maintenance see the manufacturer’s user guide.
The enabler must only be cleaned using a damp soft cloth.
Always carry this operation out with the enabler and the
telephone disconnected.
In the event of a fault in the enabler, do not handle it and
contact your distributor.
Under no circumstances should objects be inserted in the
switch’s sockets, other than floating connectors like those
indicated in the enabler’s characteristics.
6_Technical characteristics
oSocket for 3.5-mm mono female jack switch.
oPower supply: 230V~ / 50Hz.
oMaximum power supply: 250V~
oRF working frequency: 433 MHz
oDimensions: 220x190x50 mm
oThis product complies with European directives 89/336/CEE
and 73/23/CEE; you can consult the declaration of conformity
on the website given in this guide.
7_Suggestions
There are a wide range of switches and controllers to control this
enabler, please see our catalogue.
Switch input 1 Switch input 2
Table of contents
