Black & Decker The Automatic Shut-Off 62784 Installation instructions

The Automatic
Shut-Off™Iron
by Black & Decker
SAVE THIS USE AND CARE BOOK
MODEL 862784
1-800-231-9786
QUESTIONS? Please call us TOLL FREE
?
Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A.

When using your iron, basic safety precautions should always be
followed, including the following:
■Read all instructions.
■Use iron only for its intended use.
■To protect against a risk of electric shock, do not immerse the iron in
water or other liquid.
■The iron should always be turned to Off before plugging into or unplug-
ging from an outlet. Never yank cord to disconnect from outlet; instead
grasp plug and pull to disconnect.
■Do not allow cord to touch hot surfaces. Let iron cool completely
before putting away. Loop cord loosely around cordwrap when storing.
■Always disconnect iron from electrical outlet when filling with or emp-
tying of water and when not in use. Be careful to avoid spilling water
over iron when filling.
■Do not operate iron with a damaged cord or plug or if the iron has
been dropped or damaged.
■To avoid the risk of electric shock, do not disassemble the iron;
instead, take it to an authorized service center for examination and
repair. Incorrect reassembly can cause a risk of electric shock when
the iron is used.
■Close supervision is necessary for any appliance being used by or near
children. Do not leave iron unattended while connected or on an iron-
ing board. Always position iron carefully to prevent it from falling if
ironing board is accidentally moved or cord is pulled. Always use heel
rest.
■Burns can occur from touching hot metal parts, hot water, or steam.
Use caution when you turn a steam iron upside down — there may be
hot water in the water tank. Avoid rapid movement of iron to minimize
hot water spillage.
■Do not operate in the presence of explosive and/or flammable fumes.
■Do not use iron outdoors.
■This product is for household use only.
2
IMPORTANT SAFEGUARDS

SPECIAL INSTRUCTIONS
■To avoid a circuit overload, do not operate another high-wattage appli-
ance on the same circuit.
■If an extension cord is necessary, a 10-ampere rated cord with a polar-
ized plug and Underwriters Laboratories listing should be used. Cords
rated for less amperage may overheat. Care should be taken to
arrange the cord so that it cannot be pulled on or tripped over.
POLARIZED PLUG This appliance has a polarized plug—one
blade is wider than the other. To reduce the
risk of electric shock, this plug will fit into a
polarized outlet only one way. If the plug
does not fit fully into the outlet, reverse it. If
it still does not fit, contact a qualified elec-
trician. Do not attempt to defeat this safety
feature by modifying the plug in any way.
This appliance is equipped with a tamper-
resistant screw to prevent removal of the
outer cover. To reduce the risk of fire or
electric shock, do not attempt to remove the
outer cover. There are no user serviceable
parts inside. Repair should be done only by
authorized service personnel.
3
SAVE THESE INSTRUCTIONS
TAMPER-
RESISTANT
SCREW

4
Water Fill Hole
Temperature
Selector Dial
Spray Nozzle
Indicator
Mark
Adjustable
Steam/Dry Dial
Push ON Button/
Power Light
Spray/Surge Button
Pivoting Cord
Cord Wrap/
Stable Heel Rest
Large Water Windows
Water Refill Mark
Water Full Mark
Heat Setting Guide
*SilverStone®
Non-Stick Soleplate
Full-Length
Button Grooves
*SilverStone®is a trademark of E.I. DuPont de Nemours & Co.
**SurgeClean™ is a trademark of The Black & Decker Corp.
**SurgeCleanTM

IMPORTANT: Follow this procedure to clean the iron
before first use and to become familiar with its
features.
1. Remove any labels, stickers, or tags which may be
attached to the body or soleplate of the iron.
2. Fill the Water Tank about 1/3 full with water (approx-
imately 2 oz.). (See “Filling With Water,” page 6)
3. Plug the iron into a standard 120V (polarized) electri-
cal outlet.
4. Set the TEMPERATURE SELECTOR DIAL to the
Cotton or Linen settings (6 or 7). Press the PUSH ON
Button and the light will come on. Preheat for about 2
minutes. (See “Starting The Iron,” page 6)
5. While ironing on an old cotton terry cloth towel for
about two minutes, try using each of the iron’s fea-
tures being careful to avoid placing hands or face near
the steam vents:
SPRAY: Turn the SPRAY/SURGE Button so that the
Spray faces the INDICATOR MARK. Pump the SPRAY
Button a few times to see the amount of water that is
released.
SURGE OF STEAM: Turn the SPRAY/SURGE Button so
that the Surge faces the INDICATOR MARK. Pump the
SURGE Button a few times to see the blast of steam
that comes out. This will also activate the
SurgeClean™ feature that will help clean the steam
vents.
STEAM SETTINGS: Turn the ADJUSTABLE STEAM/DRY
DIAL to the INDICATOR MARK for (light), (medi-
um), and (heavy) settings to become familiar
with the different amounts of steam at each setting.
5
How To Use
PREPARING
THE IRON

FILLING WITH WATER
1. Ordinary tap water can generally
be used for ironing. However, do not
use water processed through a
home softening system.
2. In extremely hard water areas
(over 180 parts per million) consider
using distilled or demineralized
water. If using distilled or demineral-
ized water, tap water should be used
the first time you use the iron and
once per month thereafter to main-
tain steam performance.
3. When filling with water, be sure
the TEMPERATURE SELECTOR DIAL
is turned to Off and the ADJUST-
ABLE STEAM/DRY DIAL is set to Dry.
Stand the iron upright on its HEEL
REST.
4. Using a clean cup, pour approxi-
mately 6-7 oz. of water into the
WATER FILL HOLE until the water
level reaches the WATER FULL
MARK on the WATER WINDOW
(Figure A). Do not overfill. The iron
can be refilled as necessary while
hot following Steps 3 & 4.
NOTE: Never place the iron directly
under a faucet to add water.
Starting the Iron
1. Plug in the iron.
2. Press the PUSH ON Button and a
green light will come on. (Figure B).
3. Use the HEAT SETTING GUIDE on
the body of the iron to select the
setting for the fabric to be ironed.
(For more detail, see the “Fabric
Ironing Chart” on page 11).
6
Figure A
FULL
Figure B

4. Turn the TEMPERATURE SELEC-
TOR DIAL to the appropriate setting
and allow to preheat for approxi-
mately 45 seconds.
NOTE: The iron will automatically
shut off after one hour. (see
“Automatic Shut-Off” page 8)
Dry Ironing
Turn the ADJUSTABLE STEAM/DRY
DIAL to the INDICATOR MARK for
Dry to iron without steam. (Figure C)
Spray
1. Be sure the iron is filled with
water before operating the SPRAY
feature.
2. Move the TEMPERATURE SELEC-
TOR DIAL to the appropriate setting.
3. Turn the SPRAY/SURGE Button so
that the Spray (Figure D) faces the
INDICATOR MARK. Pump the
SPRAY Button a few times to get
a mist.
Surge of Steam
1. Be sure the iron is filled with water
before using the SURGE feature.
2. Move the TEMPERATURE SELEC-
TOR DIAL to a setting within the
steam band (choose one of the
settings 4 thru 7 for the appropriate
fabric).
3. Turn the SPRAY/SURGE Button so
that the Surge (Figure E) faces the
INDICATOR MARK. Pump the
SURGE Button for a concentrated
blast of steam.
7
USING MOISTURE
Figure C — Dry
Figure D — Spray
INDICATOR
MARK
INDICATOR
MARK
Figure E — Surge
INDICATOR
MARK

8
AUTOMATIC
SHUT-OFF
Adjustable Steam
1. The TEMPERATURE SELECTOR
DIAL must be set within the steam
band (settings 4 thru 7) in order to
produce adjustable steam.
2. Turn the ADJUSTABLE
STEAM/DRY DIAL to the INDICATOR
MARK for (light), (medium),
and (heavy) settings. (Figure
F) Use the HEAT SETTING GUIDE on
the body of the iron to help you
match the type of fabric to the
appropriate steam setting.
3. If water spotting occurs, reduce
the steam level and/or increase the
heat setting on the TEMPERATURE
SELECTOR DIAL.
1. The Automatic Shut-Off™ Iron is designed to shut-off
automatically after one hour whether or not it is in use.
After the iron has been on for 55 minutes, the power light
will begin to blink. It will continue to blink for 5 minutes to
alert you that the iron is getting ready to shut off.
2. To extend your ironing time once the light begins blink-
ing or to restart the iron if it has shut off automatically,
simply press the PUSH ON button and the power light will
come on.
3. To shut the iron off manually, turn the TEMPERATURE
SELECTOR DIAL to Off and unplug the iron. NOTE: Simply
turning the TEMPERATURE SELECTOR DIAL to Off will
cause the soleplate to cool down but will not shut off the
iron completely (the Power Light will stay on). The
Automatic Shut-Off feature will turn the iron off completely
after one hour.
Figure F — Adjustable Steam
INDICATOR
MARK

9
SURGE
CLEAN™
1. Turn the ADJUSTABLE STEAM/DRY DIAL to Dry.
2. Turn the TEMPERATURE SELECTOR DIAL to Off.
3. Unplug the iron.
4. Allow the iron to cool, wrap the cord, and clip it in place
using the cord clip on the plug.
5. It is not necessary to empty the water if the iron is used
frequently.
6. Store the iron on its heel rest to prevent water from
leaking from the Soleplate.
1. Using the Surge of Steam feature during regular ironing
helps clean the steam vents. At the end of an ironing ses-
sion and while the iron is still hot, use the the
SurgeClean™ feature to help flush out lint. If lint is
allowed to accumulate in the vents, it can scorch and
cause brown spotting on garments being ironed.
2. Be sure the iron has water in it. Turn the TEMPERATURE
SELECTOR DIAL to a setting within the steam band (set-
tings 4 thru 7).
3. Turn the SPRAY/SURGE Button so that the Surge faces
the INDICATOR MARK. Hold the iron over an old cloth or
over the sink and pump the SURGE Button 5 or 6 times.
Then iron over an old cloth to clean residue from the
soleplate.
Care Of The Iron
*The Automatic Shut-Off IronTM is a trademark of The Black & Decker Corp.
STORING
THE IRON

1. Is the iron plugged in and the green Power Light on?
Press the PUSH ON Button.
2. If the Light is not on, will a lamp plugged into the out-
let turn on?
3. Is the TEMPERATURE SELECTOR DIAL turned to a
fabric setting?
1. Check to see if there is enough water in the Water
Tank.
2. Is the ADJUSTABLE STEAM/DRY DIAL set at , ,
or ? Adjust the Dial to Dry and back to the
desired steam level several times.
1. Turn the TEMPERATURE SELECTOR
DIAL to Off.
2. Set the ADJUSTABLE STEAM/DRY
DIAL to the INDICATOR MARK for Dry.
3. Unplug the iron and allow it to cool.
4. Empty the water by holding the iron
over a sink with the tip pointing down-
ward (Figure G). Take care to avoid
any hot water splatter. Water will
empty out the WATER FILL HOLE.
5. If all the water hasn’t drained,
repeat the emptying process.
1. Allow the iron to cool completely.
2. Wipe the outer shell and
SilverStone®non-stick soleplate with
a cloth dampened in water and a mild
household detergent. Never use abra-
sives, heavy-duty cleansers, or scour-
ing pads.
10
EMPTYING THE IRON
Figure G
CLEANING
THE OUTSIDE
SURFACES
Need Help?
IRON
WON’T HEAT?
IRON WON’T
START
STEAMING