Black & Decker Price Pfister Catalina 48E Series User manual

08-02-04 EO6748A
27670-0500
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
Copyright
©
2004, Price P ster, Inc.
©
2004, Price P ster, Inc.
©
48E Series
Serie 48E
Série 48E
Lavatory Faucet
Grifo Para El Baño
Robinet Pour Lavabo

Thank you for purchasing this Price P ster Lavatory Faucet. All Price P ster products are carefully engineered and factory tested to provide
long trouble-free use under normal conditions. This Lavatory Faucet is easy to install using basic tools and our easy to follow illustrated
instructions. If you have any questions regarding your Lavatory Faucet installation, call 1-800-Pfaucet (1-800-732-8238).
1 BEFORE PROCEEDING
WARNING:
Read all the instructions completely before proceeding.
Price P ster recommends calling a professional if you are uncertain about
installing this product!
This product should be installed in accordance with all local and state plumbing and
building codes.
2 SHUT OFF WATER SUPPLY
Locate water supply inlets and shut off the water supply valves. These are
usually found under the sink or near the water meter. If you are replacing an
existing faucet, remove the faucet from the sink and clean the sink surface
thoroughly.
3 TOOLS RECOMMENDED
• PTFE plumber's tape or thread sealant
• Plumber's putty
• Slotted screwdriver
• Phillips head screwdriver
• Pliers
• Adjustable wrench
• Flashlight
• Cloth
Your installation may require supply lines and/or shut-off valves, cone washers,
friction rings, or other additional tools. Consult the store where your faucet was
purchased for recommended connections that may be required for you area.
4 CHECKING THE CONTENTS OF THE BOX
Upon opening the box, check to ensure that all of the following items are
included.
A
Faucet
D
Putty Plate
B
Lift Rod
E
Pop-Up Assembly
C
Wingnuts (2x)
If any of these items are missing, please contact Price P ster Consumer Service
at 1-800-Pfaucet (1-800-732-8238).
FAUCET INSTALLATION STEPS
5 PUTTY PLATE ATTACHMENT
Following manufacturer’s recommendations on use, apply plumber’s putty
into putty groove in bottom of Putty Plate (5A). Install the Putty Plate over
the three holes in your sink.
6 FAUCET INSTALLATION
Insert Faucet Shanks (6A) through the end holes of the sink. Press Deck Plate
(6B) onto Putty Plate (6C).
7 SECURING FAUCET
Align Faucet (7A) to sink surface. From underneath sink, secure Faucet using
Wingnuts (7B). Hand tighten.
5
6
7
2
3
4
2
ENGLISH
BOTTOM GROOVE
5A
A
B
C
D
E
7A
7B
7A
7B
7B
6A
6A
6B
6C

8 WATER SUPPLY CONNECTIONS
Connect water Supply Lines (8A) to Faucet Inlets (8B).
(Supply lines and
 ttings are not included).
9 POP-UP ROD CONNECTION
Insert Lift Rod (9A) into hole at the back of Spout (9B). Gently, slide Lift Rod
(9A) down the hole in Spout Hub (9B).
POP-UP DRAIN BODY INSTALLATION STEPS
10 POP-UP PREPARATION
Remove Flange (10A) and unscrew Nut (10C) from the Pop-Up Drain Body
(10B). Retain the Packing Ring (10D) inside the Ball Rod Opening (10E). Take
off the Spring Clip (10F) from the Ball Rod (10G). Place the Nut (10C) over
the Ball Rod (10G). Remove Locknut (10H), Friction Washer (10J), Rubber
Washer (10K), and Stopper (10L) from Flange (10A).
11 POP-UP INSTALLATION
Apply a small bead of putty underneath the Flange (11A) and place a ring of
putty around Drain Opening (11B) of sink. Use PTFE plumber’s tape to all
threaded  ttings according to manufacturer’s instructions. Insert Flange (11A)
into Drain Opening (11B). From underneath, insert Rubber Washer (11C) and
Friction Washer (11D) over the bottom of Flange (11A). Thread Locknut (11E)
until Rubber Washer (11C) seats securely inside Drain Opening (11B). Thread
Drain Body (11F) to bottom of Flange (11A). Hand tighten and adjust the Drain
Body so that the Ball Rod Opening (11G) faces the rear. Wrench tighten Locknut
(11E) and wipe excess putty.
12 BALLROD ADJUSTMENT
Drop the Stopper (12A) into the Drain Body (12B) from the top with the Off-Set
(12C) facing rear. From below, insert the Ball Rod (12D) into the Ball Rod Opening
(12E) through the Stopper Hole (12F) and secure with the Nut (12G).
8
9
10
11
12
3
ENGLISH
8A
8B
9A
9B
10C
10A
10A
10B
10D
10E
10F
10G
10K
10H
10A
10A
10L
10B
10G
10J
10C
11F
11E
11D
11C
11A
11B
11G
12F
12D
12A
12B
12C
12D
12E
12G
12G

13 POP-UP ROD LINKAGE & ADJUSTMENT
Place one end of Spring Clip (13C) on end of Ball Rod (13B). Insert Ball Rod
(13B) across and through hole in Strap (13D). Secure other end of Spring Clip
(13C). Insert bottom of Lift Rod (13A) into hole at top of Pop-Up Strap (13D).
Tighten with Thumb Screw (13E). Adjust Lift Rod (13A) function by adjusting
location of Thumb Screw (13E) along the Strap (13D) or by adjusting the hole in
which Ball Rod (13B) goes through Strap (13D). Be sure to leave enough space
between Lift Rod Knob (13F) and Spout Hub (13G) when Lift Rod is down.
14 UNIT START UP
Turn on hot and cold water supplies, and check for leaks above and below
the sink.
FAUCET FUNCTIONS
15 VALVE FUNCTION
COLD valve: close-counterclockwise, open-clockwise; HOT valve: close-
clockwise, open-counterclockwise.
MAINTENANCE & CARE
16 FLUSHING & AERATOR CLEANING
After installation is complete, remove Aerator Housing (16A). Turn Valves
(16B) on and allow both hot and cold water to run for at least one minute each.
While water is running, check for leaks. To clean the aerator, disassemble Aerator
Housing (16A) by separating the Aerator Shell (16C), Basket (16D), and Washer
(16E). Once parts have been cleaned, reassemble by reversing steps.
13
15
16
14
4
ENGLISH
HOT
COLD
CLOSED
OPEN
CLOSED
OPEN
16E
16D
16C
16A
16A
16B
13G
13F
13C
13C
13B
13B
13D
13D
13E
13E
13A
13A
13A
13A

17 HANDLE REMOVAL
Turn off water before proceeding!
With valves in closed position, detach
Decorative Button (17A), unscrew Fastener (17B), and remove Handle Hub
(17C) from Valve Stem (17D).
18 VALVE CARTRIDGE MAINTENANCE
Turn off water supplies and relieve pressure before working on your
faucet.
Remove handles
(See Step 17)
, unscrew Cartridge Assembly (18A) and
inspect. Replace parts as necessary. Reassemble parts by reversing steps.
1-800-PFAUCET (1-800-732-8238)
For Toll-Free Pfaucet information call
1-800-PFAUCET (1-800-732-8238)
or visit www.pricep ster.com
• Installation Support
• Care and Warranty Information
CAUTION: Maintenance
DISASSEMBLY
1.
Replacement parts may be available at the store
where you purchased your faucet.
2.
When replacement parts are not available, please
write or call Price P ster Consumer Service.
3.
Always turn off water and relieve pressure before
working on your faucet.
NOTE: Trim Care
Cleaning Instructions:
For all handles and decorative  nishes, use only a soft
damp cloth to clean and shine. Use of polish, detergents,
abrasive cleaners, organic solvents, or acid may cause
damage.
Use of other than a soft damp cloth will
nullify our warranty!
Special Trim:
Trim products which contain porcelain or other similar
substances are not acceptable for public areas or
commercial use. Installation of said trim is at user’s risk!
17 18
5
ENGLISH
17A
17A
17B
17C
17D
18A
18A

19701 DaVinci
Lake Forest, CA 92610
Phone: 1-800-Pfaucet
www.pricep ster.com
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
48E Series
Serie 48E
Série 48E
Lavatory Faucet
Grifo Para El Baño
Robinet Pour Lavabo
*
*
Letter Designates FinishLetter Designates Finish
La Letra Indica el Terminado
La Letra Indica el Terminado
La Lettre Designe La FiniLa Lettre Designe La Fini
A
Polished Chrome
Cromo Pulido
Chrome Poli
AV
Polished Chrome
with Brass Accent
Acabado de Cromo Pulido
con Extremo de Latón
Chrome Poli Fini avec
Bout en Laiton
F
PVD Brushed Brass
PVD Latón Cepillado
PVD Laiton Balayé
J
PVD Brushed Nickel
PVD Niquel Cepillado
PVD Nickel Brosse
V
PVD Polished Brass
PVD Latón
Pulido
PVD Laiton Poli
Z
Oil Rubbed Bronze
Bronce Frotado Con Aceite
Bronze Huilé
941-044*
910-024
Hot
Caliente
Chaud
910-025
Cold
Frío
Froid
940-048
Porcelain
Porcelana
Porcelaine
972-019*
971-702
941-049*
941-047*
940-049*
941-200*
931-960
974-027
940-047*
Metal
Metal
Métal