Black & Decker Price Pfister 48-N Series User manual

48-N Series
Serie 48-N
Série 48-N
Lavatory Faucet
Grifo Para El Baño
Robinet Pour Lavabo
09-22-04 EO6773C
29163-0200
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
Copyright
©
2004, Price Pfi ster, Inc.
©
2004, Price Pfi ster, Inc.
©

Thank you for purchasing this Price Pfi ster Lavatory Faucet. All Price Pfi ster products are carefully engineered and factory tested to provide
long trouble-free use under normal conditions. This Lavatory Faucet is easy to install using basic tools and our easy to follow illustrated
instructions. If you have any questions regarding your Lavatory Faucet installation, call 1-800-Pfaucet (1-800-732-8238).
1 BEFORE PROCEEDING
WARNING:
Read all the instructions completely before proceeding.
Price Pfi ster recommends calling a professional if you are uncertain about
installing this product!
This product should be installed in accordance with all local and state plumbing and
building codes.
2 SHUT OFF WATER SUPPLY
Locate water supply inlets and shut off the water supply valves. These are
usually found under the sink or near the water meter. If you are replacing an
existing faucet, remove the faucet from the sink and clean the sink surface
thoroughly.
3 TOOLS RECOMMENDED
• PTFE plumber's tape or thread sealant • Plumber's putty
• Slotted screwdriver • Phillips head screwdriver • Pliers
• Adjustable wrench • Flashlight • Cloth
Your installation may require supply lines and/or shut-off valves, cone washers,
friction rings, or other additional tools. Consult the store where your faucet was
purchased for recommended connections that may be required for you area.
4 CHECKING THE CONTENTS OF THE BOX
Upon opening the box, check to ensure that all of the following items are
included.
A
Faucet
D
Lift Rod Button
B
Lift Rod
E
Pop-Up Assembly
C
Wingnuts (2x)
If any of these items are missing, please contact Price Pfi ster Consumer Service
at 1-800-Pfaucet (1-800-732-8238).
FAUCET INSTALLATION STEPS
5 FAUCET INSTALLATION
Following manufacturer’s recommendations on use, apply plumber’s putty
into putty groove in bottom of Putty Plate (
5A
). Insert Faucet Shanks (
5B
)
through the end holes of the sink (
5C
).
6 SECURING FAUCET
Align Faucet (
6A
) to sink surface. From underneath sink, secure Faucet using
Wingnuts (
6B
). Hand tighten.
5
6
2
3
4
2
ENGLISH
BOTTOM GROOVE
A
B
C
D
E
6A
6B
6A
6B
6B
5C
5C
5B
5A

7 WATER SUPPLY CONNECTIONS
Connect water Supply Lines (
7A
) to Faucet Inlets (
7B
).
(Supply lines and
fi ttings are not included).
8 POP-UP ROD CONNECTION
Insert Lift Rod (
8A
) into hole at the back of Faucet (
8B
). Gently, slide Lift Rod
(
8A
) down the hole in Faucet (
8B
).
POP-UP DRAIN BODY INSTALLATION STEPS
9 POP-UP PREPARATION
Remove Flange (
9A
) and unscrew Nut (
9C
) from the Pop-Up Drain Body
(
9B
). Retain the Packing Ring (
9D
) inside the Ball Rod Opening (
9E
). Take
9E). Take 9E
off the Spring Clip (
9F
) from the Ball Rod (
9G
). Place the Nut (
9C
) over
the Ball Rod (
9G
). Remove Locknut (
9H
), Friction Washer (
9J
), Rubber
Washer (
9K
), and Stopper (
9K), and Stopper (9K
9L
) from Flange (
9A
).
10 POP-UP INSTALLATION
Apply a small bead of putty underneath the Flange (
10A
) and place a ring of
putty around Drain Opening (
10B
) of sink. Use PTFE plumber’s tape to all
threaded fi ttings according to manufacturer’s instructions. Insert Flange (
10A
)
into Drain Opening (
10B
). From underneath, insert Rubber Washer (
10C
) and
Friction Washer (
10D
) over the bottom of Flange (
10A
). Thread Locknut (
10E
)
10E) 10E
until Rubber Washer (
10C
) seats securely inside Drain Opening (
10B
). Thread
Drain Body (
10F
) to bottom of Flange (
10F) to bottom of Flange (10F
10A
). Hand tighten and adjust the Drain
Body so that the Ball Rod Opening (
10G
) faces the rear. Wrench tighten Locknut
(
10E
) and wipe excess putty.
10E) and wipe excess putty.10E
11 BALLROD ADJUSTMENT
Drop the Stopper (
11A
) into the Drain Body (
11B
) from the top with the Off-Set
(
11C
) facing rear. From below, insert the Ball Rod (
11D
) into the Ball Rod Opening
(
11E
) through the Stopper Hole (
11E) through the Stopper Hole (11E
11F
) and secure with the Nut (
11F) and secure with the Nut (11F
11G
).
7
8
9
10
11
3
ENGLISH
7A
7B
8A
8B
9C
9A
9B
9D
9E
9F
9G
9K
9H
9A
9L
9B
9G
9J
9C
10F
10E
10D
10C
10A
10A
10B
10G
11F
11D
11A
11B
11C
11D
11E
11G

12 POP-UP ROD LINKAGE & ADJUSTMENT
Place one end of Spring Clip (
12C
) on end of Ball Rod (
12B
). Insert Ball Rod
(
12B
) across and through hole in Strap (
12D
). Secure other end of Spring Clip
(
12C
). Insert bottom of Lift Rod (
12A
) into hole at top of Pop-Up Strap (
12D
).
Tighten with Thumb Screw (
12E
). Adjust Lift Rod (
12E). Adjust Lift Rod (12E
12A
) height by using the
Thumb Screw (
12E
) on the Strap (
12E) on the Strap (12E
12D
) or by adjusting the hole in which Ball
Rod (
12B
) goes through Strap (
12D
). Be sure to leave enough space between
Lift Rod Knob (
12F
) and Spout Hub (
12F) and Spout Hub (12F
12G
) when Lift Rod is down.
13 UNIT START UP
Turn on hot and cold water supplies, and check for leaks above and below
the sink.
14 VALVE FUNCTION
COLD valve: close-counterclockwise, open-clockwise; HOT valve: close-
clockwise, open-counterclockwise.
15 FLUSHING & AERATOR CLEANING
After installation is complete, remove Aerator Housing (
15A
). Turn Valves
(
15B
) on and allow both hot and cold water to run for at least one minute each.
While water is running, check for leaks. To clean the aerator, disassemble Aerator
Housing (
15A
) by separating the Aerator Shell (
15C
), Basket (
15D
), and Washer
(
15E
). Once parts have been cleaned, reassemble by reversing steps.
15E). Once parts have been cleaned, reassemble by reversing steps.15E
FAUCET FUNCTIONS
MAINTENANCE & CARE
12 14
15
13
4
ENGLISH
HOT
COLD
CLOSED
OPEN
CLOSED
OPEN
15E
15D
15C
15A
15A
15B
12G
12F
12C
12C
12B
12B
12D
12D
12E
12E
12A
12A
12A
12A

16 HANDLE REMOVAL
Turn off water before proceeding!
With valves in closed position, loosen
Fastener (
16A
), and remove Handle Hub Assemblies (
16B
) from Valve Stem
(
16C
).
17 VALVE CARTRIDGE MAINTENANCE
Before working on your faucet, turn off water supplies and relieve pressure
by turning on both hot and cold valves.
Remove handles
(See Step 16)
,
unscrew Cartridge Assembly (
17A
) and inspect. Replace parts as necessary.
Reassemble parts by reversing steps.
1-800-PFAUCET (1-800-732-8238)
For Toll-Free Pfaucet information call
1-800-PFAUCET (1-800-732-8238)
or visit www.pricepfi ster.com
• Installation Support
• Care and Warranty Information
CAUTION: Maintenance
DISASSEMBLY
1. Replacement parts may be available at the store
where you purchased your faucet.
2. When replacement parts are not available, please
write or call Price Pfi ster Consumer Service.
3. Always turn off water and relieve pressure before
working on your faucet.
NOTE: Trim Care
Cleaning Instructions:
For all handles and decorative fi nishes, use only a soft
damp cloth to clean and shine. Use of polish, detergents,
abrasive cleaners, organic solvents, or acid may cause
damage.
Use of other than a soft damp cloth will
nullify our warranty!
Special Trim:
Trim products which contain porcelain or other similar
substances are not acceptable for public areas or
commercial use. Installation of said trim is at user’s risk!
16
17
5
ENGLISH
16A
16A
16B
16C
17A
17A