BLAUBERG Ventilatoren EH-13 100 User manual

EH13 100
EH13 125
EH13 160
EH13 150x150
EH13 164x164
Outer ventilation hood with frost protection
INSTALLATION INSTRUCTION

2
EH-13
www.ventilation-system.com
OVERALL DIMENSIONS
The outer ventilation hood is designed to prevent ingress of water and foreign objects into the ventilation equipment from outside and
to protect the ventilation duct and equipment inside it from frost.
PURPOSE
THE UNIT SHOULD NOT BE OPERATED BY CHILDREN OR PERSONS WITH REDUCED
PHYSICAL, MENTAL, OR SENSORY CAPACITIES, OR THOSE WITHOUT THE APPROPRIATE
TRAINING. THE UNIT MUST BE INSTALLED AND CONNECTED ONLY BY PROPERLY
QUALIFIED PERSONNEL AFTER THE APPROPRIATE BRIEFING.
THE CHOICE OF UNIT INSTALLATION LOCATION MUST PREVENT UNAUTHORIZED
ACCESS BY UNATTENDED CHILDREN.
137
(5 3⁄8")
BD
C
C
A
Model АB C D
EH-13 100 240 mm
(9 7/16”)
260 mm
(10 1/4”) -112 mm (4 7/16”)
EH-13 125 280 mm
(11”)
300 mm
(11 13/16”) -137 mm (5 3/8”)
EH-13 160 280 mm
(11”)
300 mm
(11 13/16”) -162 mm (6 3/8”)
EH-13 150х150 280 mm
(11”)
300 mm
(11 13/16”)
136 mm
(5 3/8”) -
EH-13 164х164 280 mm
(11”)
300 mm
(11 13/16”)
160 mm
(6 5/16”) -
DESIGN AND OPERATING PRINCIPLE
Heating element with a thermostat
Power cable
Front part of the ventilation hood
When the outdoor temperature drops below -10 °C (-14 °F), the thermostat switches on the heating cable, thus protecting the hood,
ventilation duct and the products in it against frost.

3
www.ventilation-system.com
1. Insert the air duct from indoor to protrude from outside on
the outer wall surface.
Cut the air duct excess with a hack saw or with any other
suitable tool.
WARNING! If the mounting place is located at high
altitude please refer to a mounting company possessing
an appropriate mounting equipment!
10 mm
(3/8")
Foam wedge
Following the installation of the hood and
cable routing, fill the gaps between the air
duct and the opening with a mounting
foam.
2. Mark the fastening holes for the outer ventilation hood and
drill 4 holes, 50 mm (2”) deep to suit the expansion anchors
(6x40) 6 mm (/”)x40 mm (1/”).
Use the back wall of the ventilation hood to facilitate the
marking.
200 mm
(7 7/8")
Ø6 mm (¼")
4 holes
220 mm
(8 11/16")
EH-13 125 | 160 | 150х150 | 164x164 EH-13 100
160 mm
(6 5/16")
Ø6 mm (¼")
4 holes
180 mm
(7 1/16")
3. Insert the supplied expansion anchors
6 mm (/”)x40 mm (1/”) into the holes.
Disassemble the outer ventilation hood to enable access to the
fastening holes. Remove the ventilation hood front part.
4. Lay the ventilation hood power cord from the outer side of
the air duct.
Fix the back part of the ventilation hood on the wall using the
supplied screws 4 mm (/”)x40 mm (1/”).
Connect the power cord in the room according to the wiring
diagram.
OUTER VENTILATION HOOD MOUNTING

4
EH-13
www.ventilation-system.com
CONNECTION TO POWER MAINS
Outer ventilation hood is equipped with frost protection. The power consumption of the hood depends on the temperature conditions
and is no more than 60 W (230 V/50 Hz). Sustaining current is 0.26 A.
TERMINAL DESIGNATIONS ON THE WIRING DIAGRAM:
L - phase
N - 0
QF- automatic circuit breaker
L
N
QF
blue
yellow-green
Outer ventilation hood with heating
brown
5. Cover the ventilation hood with the front part.
CAUTION! The hood is approved for use at temperatures from -35 °C (-22 ˚F) to +50 °C(+122 ˚F) .
The manufacturer cannot guarantee correct operation of the hood under conditions other than those specied.
The warranty period is 12 months from the date of purchase.
The Supplier is particularly not liable for damages arising during transportation, incorrect handling and unapproved modifications or repair work.
MANUFACTURER’S WARRANTY
EH-13 is recognized as serviceable
Quality Inspector’s Stamp Manufacture Date _____________________________________________
Seller
Name of Retail Company, Stamp of the Shop__________________________________________________________________
_________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________
Purchase Date_____________________________
OUTER VENTILATION HOOD WITH FROST PROTECTION

5
www.ventilation-system.com

6
EH-13
www.ventilation-system.com

7
www.ventilation-system.com

V113-10EN-01