Blaupunkt CA1.0 User manual

Enjoy it.
Operating and Installation Instructions
VEHICLE SECURITY
SYSTEM CA1.0/CA2.0
CA1.0
CA2.0

Safety Notes
This vehicle security system has been man-
ufactured according to established safety
guidelines. However, dangers may still occur
if the safety notes in this manual is not ob-
served. This manual is intended to familiarize
the user with the vehicle security system’s
important functions. Read this carefully, prior
to using the vehicle security system. Keep
this manual in an easily accessible location.
In addition, do observe the instructions of
the devices used in conjunction with this
vehicle security system.
Attentions
•
•
•
•
This manual may be updated from time to
time without any notice.
Keep the device in a dry and well-ventilat-
ed environment.
Do not drop the device or subject it to
physical shock.
Improper use or replacement of the
battery may cause in explosion hazard.
Replace with the equivalent type only.
The vehicle security system is a
complicated technical device implying
connection to the car circuits related to
engine operation. It is strongly advised to
have a professional car mechanic installing
the system.
Disclaimer
In no event shall Blaupunkt be liable for any
direct, indirect, punitive, incidental, special
consequential damages to property or life
and whatsoever arising out of or connected
with the use or misuse of our products.
USA & CANADA: This product is not intended
for sale in the United States and Canada. If
purchased in the U.S. or Canada, this product
is purchased on as-is basis. No warranty,
whether expressed or implied is provided in
the U.S. or Canada.
1
CAUTIONS

2
STRUCTURE
SPECIFICATIONS
Function
Arm
Disarm
Panic
Trunk Release
Beep Sound (Silent)
Auto Relock (Default: Activated)
Foot Brake Lock (Default: Activated)
Valet Mode (Default: Activated)
Exit Delay Time (5 & 30Sec) (Default: Activated)
Remote Arm, Disarm and Panic
Remote Silent Arm and Disarm
Remote Boot Release
Beep Sound (Remote Selectable)
Auto Relocking / Auto Rearming (Remote
Selectable)
Foot Brake Lock (Remote Selectable)
Valet Mode (Remote Selectable)
Door Not Closed Warning (Remote
Selectable)
Exit Delay Time 5 or 30 sec. (Remote
Selectable)
Door Open Detection
2 Ports Three Wire Dual Zone Shock
Sensor
Passive Immobilizer
Code Learning Technology
•
•
•
•
•
•
•
•
•
•
•
•
•
Button
Button 1
Button 2
Button 3
Hold Button 2 /4
Button 1 & 2
Hold Button 1
Hold Button 2
Hold Button 1 & 2
Hold Button 3
Ignition Status
OFF
OFF
OFF
OFF
OFF
ON (Deactivate)
ON (Deactivate)
ON (Deactivate)
ON (Deactivate)
CA1.0 CA2.0
1 1
44
2 2
33

FUNCTIONS
Press Button 1 to arm.
The central lock will be lock, alarm will
beep once, hazard light ashes and LED
light will turn on.
The immobilizer will function if the
ignition is turned ON.
Press Button 2 to disarm.
The central lock will be unlocked and
alarm will beep twice.
Hazard light ashes twice and LED light
will turn o.
Press Button 1 and 2 simultaneously to
disable Beep sound, hazard light will
ash twice.
Repeat the same step to enable the
Beep sound.
The alarm will beep and hazard light
will ash.
Press Button 3 to trigger the alarm and
hazard light for approx. 45 sec. instantly
in case of emergency.
Press buttons other than Button 3 to turn
o the alarm, alarm system will remain
armed and locked.
After 30 seconds of disarming the alarm
system and no doors are being open, the
system will automatically relock / rearm
the vehicle.
If the central locking was accidentally
unlocked after 15 sec. second alarm will
beep and hazard light ashes, indicating
the system will be rearmed and the door
will be relocked in another 15 sec.
To disable this function, turn on the
ignition, press and hold Button 1 for
2 sec., the alarm will beep twice and
hazard light ashes.
Repeat the same step to enable this
function again, alarm will beep once and
hazard light ashes.
This function will be activated either
after the ignition is turned o for 60 sec.
at disarm mode or 60 sec. passed after
Button 2 is pressed.
The passive immobilizer sends out signal
to stop the electronic start/ ignition
circuit in order to immobilize the vehicle.
The blinking LED indicates the function
is enabled.
To Cancel the passive immobilizer, press
Button 2; the LED will stop blinking
indicating the function is disabled.
Note : The auto-relock function will over-
ride passive immobilizer function.
The alarm will be triggered if any zones
are opened while the alarm status is in
armed mode.
The siren will last for 45 sec. and 5 sec.
break, every time the system check for
the zone status.
Upon completion of 3 zone status check-
ing, the violated port is ignored and the
system will be rearmed.
1. Arm (Lock)
•
•
•
2. Disarm (Unlock)
•
•
•
3. Beep Sound (Remote Selection)
•
•
•
4. Panic
•
•
5. Auto Relock/ Auto Rearm
(Remote Selection)
•
•
•
•
6. Passive Immobilizer
•
•
•
7. Doors/ Boot/ Bonnet Zone Protection
•
•
•
3

8. Key on Trigger Zone
•
•
9. Manual Override System
•
10. Ignition / Starter Disable (External
Heavy Duty 30A Relay)
•
11. 3 Independent Triggering Zones
with Memory
•
•
•
FUNCTIONS
The alarm will be triggered if the alarm is
in arm mode and the ignition is ON.
The siren will continue for 45 sec. before
it takes 5 sec. to check on the ignition
status, the siren will continue if alarm is
still in arm mode while ignition is ON.
To set o the alarm system without
using a the remote in case of missing/
malfunction remote, turn on the ignition
and press the Reset switch once.
When the alarm system is in arm mode
and ignition is ON, the system will halt
the ignition (subject to relay connection)
and the alarm will be triggered. This will
immobilize the vehicle to prevent car
from being stolen.
There are sensors on the doors/ bonnet/
boot & ignition key zones.
The alarm will beep 3 times after the
alarm is disarmed, indicating doors/
bonnet/ boot zone is triggered; 4 times
indicate sensor, 5 times indicate ignition
key zone triggered.
The memory will automatically be
erased when the ignition is turned on in
disarm mode.
A dashboard mounted red arm and
memory LED will light up to indicate
when the alarm system is arm, disarm,
triggered.
To turn on the Valet Mode, then the
ignition ON, press Button 1 and 2 for
hold for 2 sec., the alarm will beep once
and hazard light ashes, the arm LED
ashes too.
The alarm system will be disabled when
in valet mode (Not include Central Lock
System).
To return to normal mode, repeat the
same steps again while the ignition
is ON.
In disarm mode, when the alarm system
detects opened doors and the ignition is
ON, the hazard light ashes.
The hazard light will stop ashing when
the doors are closed.
When door lock mode is activated, alarm
will beep and hazard light ashes when
the doors are opened.
After 30 sec., the alarm will be trigger.
To disable this function, follow the Exit
Delay Time Selection.
12. LED Indicator shows the Status of
the Security System
•
13. Valet Mode (Remote Selection)
•
•
•
14. Door Open Detection
•
•
15. Opened Door Warning (Remote
Selection)
•
•
•
4

FUNCTIONS
TROUBLESHOOTING
Exit delay time (5/ 30 sec.) can be select-
ed by the remote control.
For exit delay time 5 sec., turn ON the
ignition, then press and hold the Button
3, the alarm will beep twice and hazard
light ashes.
When select exit delay time 5 sec.,
opened door warning function will be
disabled.
Repeat the same procedure again for the
exit delay time to 30sec., the alarm will
beep once and hazard light ashes.
Press and hold Button 2 or 4 (open trunk
signal output is required).
The alarm system will automatically
disarm each time the trunk is opened.
If the vehicle is hit by light impact, the
alarm will release a warning beep.
If the vehicle is hit by high impact, the
alarm will release the siren for 45 sec.
before it stops.
Turn the ignition ON & OFF, repeat the
steps 5 times, then keep the ignition ON.
Press any button on the remote, LED
light will be on without ashes. Press any
button again, the LED light will be o,
indicating pairing successful.
The LED will blink again as a sign for
ready learning once more. Repeat step
b. again for up to 6 pairing. A maximum
of 10 sec. is allowed for each complete
learning at one time.
After completed pairing, turn o the
ignition to exit the pairing process.
16. Exit Delay Time (Remote Selection)
•
•
•
•
17. Trunk Release Activation by Remote
(Optional)
•
•
18. 3 Wire Dual Zone Shock Sensor
(TWDZ) Optional
a)
b)
19. Transmitter Pairing Process
a)
b)
c)
d)
5
If any of the following problem occur, please resort to Troubleshooting for the possible
solutions. Consult Blaupunkt authorized dealer if problem persist.
Problems
Remote does not work
System will not arm
Possible Causes
Remote is not proggrammed
or not pair.
Weak or stale battery.
Power supply problem.
Remote is not functioning.
Solutions
Program remote and check
the wire connection.
Replace with a new and
equivalent type of battery.
Check +12V & ground (earth)
at the system module.
Check the battery level of
the remote.

6
WIRING DIAGRAM
Shock Sensor (Optional)
LED Status Indicator
Reset Switch
1 White / Yellow
Hazard Light
2 White / Yellow
3 Green
4 Blue
Central Locking
Yellow
12 White
5 Black
Brake Light
Blue
Yellow
Red
Front View
1
2
3
4
5
6
7
8
9
10
11
12
13
:
:
:
:
:
:
:
:
:
:
:
:
:
Hazard Light
Hazard Light
Lock (Relay)
Unlock (Relay)
Ground
+12V DC
Door Switch
(-) Output
Siren
Foot Brake
Key On
Unlock (-)
Lock (-)
Antenna
Boot Release Module
(Optional)
Green
10 Green/ Black
Foot Brake Switch
(Optional)
11 Orange / White
6 Red
7 Orange
Black Black
8 Grey
Orange / White
To Start Solenoid To Ignition Switch
9 Brown
Existing Low Current Solenoid
Feed Wire (+12V DC, Key “ON”only)
Ignition Key (ON)
Door / Bonnet / Boot
13 Brown / White
Ultra Sonic Sensor
(Optional)
+ 12VDC
+ 12VDC
Blue
Yellow

Designed and engineered by Blaupunkt Competence Centre
VSS CA1.0
1 521 20 011 23 01
VSS CA2.0
1 521 20 012 23 01