Blaupunkt AUGSBURG CR 24 User manual

Operating instructions
Augsburg CR 24

3
Augsburg CR 24 (Code deaktiviert)
ENGLISH
ITALIANO
PORTUGUES NEDERLAND
ESPAGÑOL SVENSKA FRANÇAIS
16
79 810
3 42
11
5

13
Augsburg CR 24
DEUTSCH
ENGLISH
ITALIANO
PORTUGUES NEDERLAND
ESPAGÑOL SVENSKA FRANÇAIS
Contents
Short description ......................... 14
Important information.................. 16
What you need to know! ....................... 16
Traffic safety ......................................... 16
Installation/connection .......................... 16
Anti-theft coding .......................... 16
Wrong code number entered ................ 16
Switching the code system on .............. 17
Restart following interruption of power
supply.................................................... 17
Switching the code system off .............. 17
Optical indication of theft protection ...... 17
Radio operation............................ 18
Station search ....................................... 18
Manual station search........................... 18
Adjusting the station search sensitivity . 18
Stereo - mono switch ............................ 18
Changing the memory bank .................. 18
Storing stations ..................................... 18
Storing the strongest stations auto-
matically with Travelstore...................... 19
Recalling stored stations ....................... 19
Sampling stored stations briefly with
Preset-Scan .......................................... 18
Sampling stations briefly
with Radio-Scan .................................... 19
Traffic messages (ARI) ................ 20
Switching the traffic messages (ARI)
on and off .............................................. 20
Warning beep........................................ 20
Switching the warning beep off ............. 20
Automatic search start .......................... 20
Adjusting the volume for traffic messages
and warning beep ................................. 21
Tape operation ............................. 21
Inserting the tape .................................. 21
Ejecting the cassette............................. 21
Fast tape run ......................................... 21
Autoreverse function ............................. 22
Care of your audio equipment............... 22
Appendix....................................... 22
Technical data....................................... 22

Augsburg CR 24
14
2Rocker switch
Station search
up
down in
short intervals
down
up in
short intervals
Extra function:
Coding Confirm with after having
entered the code.
3Eject cassette tape
Press
4Cassette tape slot
Insert cassette (side A or 1 facing up, the
open side facing to the right).
Short description
1Amplifier
Tone Balance
On Off
Volume
Scan: Press for 1 second.
When “Cod” lights up in the display,
read chapter “Anti-theft coding” first.
Balance
To adjust the volume of the left and
right channel.
SCAN
Press for approximately 1 second to
sample all stations to be received.
5Rapid tape run/Autoreverse
Side A or 1 Side B or 2
Track indication
Switch-over to the other track
Press simultaneously
Fast
forward;
To stop: press FR
Fast
rewind;
To stop: press FF
6Display
Wave band
Frequency
Memory bank
Preset button
ARI priority
ARI
station code
Stereo
Sensitivity
(station search)

15
Augsburg CR 24
DEUTSCH
ENGLISH
ITALIANO
PORTUGUES NEDERLAND
ESPAGÑOL SVENSKA FRANÇAIS
71, 2, 3, 4, 5, 6 - preset buttons
For each memory bank (I, II, III) you
can store up to 6 stations.
To store a station: Press button during
radio operation and hold it. First the
station will be muted and then becomes
audible again.
To recall a station: Select the memory
bank using the FM•T button and press
the respective preset button (press re-
peatedly if necessary).
Extra function:
Coding - Read chapter “Anti-theft cod-
ing” first.
Buttons 1, 2, 3, 4 - To enter the code.
Press each button repeatedly until the
code of the car radio pass is indicated
in the display.
8lo
Station search sensitivity
“lo” lit up in the display indicates normal
sensitivity for the station search func-
tion (the system will pick up strong sta-
tions only).
“lo” not lit up in the display indicates
high sensitivity for the station search
function (the system will also pick up
weaker stations).
To change the search sensitivity:
press lo.
9ARI - traffic messages
When ARI is visible in the display, you
can only listen to those radio stations
which broadcast traffic messages.
ARI on/off: press button.
:FM•T - FM, Travelstore
Selector for the FM memory banks I, II,
III and “T” (Travelstore).
To change the memory bank:
Press button until the desired memory
bank in indicated in the display.
To store the six nearest, strongest stati-
ons automatically with Travelstore:
Store: Press FM•T until the search
starts in the display.
Recall: Press FM•T until “T” appears in
the display. Then briefly press one of
the presets 1, 2, 3, 4, 5, 6.
;PS (Preset-Scan)
To sample all stored stations of the
selected memory bank (FM I-III or T)
briefly.

Augsburg CR 24
16
Important information
What you need to know!
Beforestarting to use your new car radio you
shouldcarefullyreadthroughtheinformation
on “Traffic safety” and “Anti-theft coding”.
Traffic safety
Traffic safety has always priority. Use your
car radio in such a manner that you are
always able to cope with and react to the
prevailing traffic situation at any given time.
Remember, even at 50 km/h you are still
moving at a speed of 14 m per seconds.
It is also very important that you are able to
hear, and react to, acoustic warning signals
around you, for example from the police or
the firebrigade.
Therefore, adjust the volume reasonably.
Installation/connection
The code system can only be switched on
and off, if the radio is connected to perma-
nent power.
If you like to install your new car radio by
yourself or add other audio components to
the existing ones, then please read carefully
the enclosed instructions on installation and
connection.
Do not connect the loudspeaker outputs to
ground!
Only use the accessory and replacement
parts approved by Blaupunkt.
Anti-theft coding
The car radio comes standard with the code
system deactivated.
If the anti-theft coding system is on while the
power supply to the unit is interrupted (e.g.
theft,disconnectingthecarbattery),thesetis
electronically blocked. Then it may only be
used again after the appropriate code num-
ber has been entered (see car radio pass-
port).
Wrong code number entered
Itshouldnotbe possible forthievestoascer-
tain the code number by trial-and-error. This
is why the set will be blocked for a certain
period of time, if an incorrect code number is
entered. In this case, “- - -” will appear in the
display.
This waiting time is 10 seconds after the first
three attempts, and 1 hour following subse-
quent attempts.
After 19 unsuccessful attempts, “OFF” will
appear in the display and the set can no
longer be restarted.
Note:
Keep you car radio passport with the code
number in a safe place in order to avoid
“unauthorized access” to your car radio.

17
Augsburg CR 24
DEUTSCH
ENGLISH
ITALIANO
PORTUGUES NEDERLAND
ESPAGÑOL SVENSKA FRANÇAIS
If the power supply to the radio is interrupted
while the code system is switched on, you
need to know the right code number.
The radio will operate again as soon as you
have entered the right code number.
If you lose your radio passport and have
forgotten your code number, you will not be
able to restart the set after the power supply
hasbeeninterrupted.Inthiscase, your radio
can only be reset in our central customer
service workshop or in one of our service
agencies abroad.
Switching the code system on
Precondition:
The radio must be connected to permanent
power.
In order to switch the code system on:
•Turn the radio off.
• Hold down the preset buttons 1and 4
simultaneously.
•Turn the radio on.
“Cod” briefly appears before the radio
begins to operate.
•Release preset buttons 1and 4.
The code system is on.
“Cod” will be briefly displayed each time the
radio is turned on.
Now it is essential to enter the correct code
after the waiting period has elapsed (Cod in
the display).
If the radio is turned off before the waiting
period has elapsed, then the waiting period
restarts as soon as the radio is turned on
again.
Switching the code system off
•Turn off the radio.
•Simultaneously press preset buttons 1
and 4and hold them down.
•Turn the set on.
“Cod” will appear in the display.
•Enter the code number given in the
Blaupunkt car radio passport and con-
firm: See example “Restart following
interruption …”.
The code system is now deactivated.
Optical indication of theft protec-
tion
As optical warning of the encoded car radio,
the LED 5flashes when the ignition is
switchedoff,providedthecarradiohasbeen
connected correspondingly.
For this, please read through the installation
instructions.
Restart following interruption of
power supply
(Code system switched on)
•Switch on the set.
“Cod” will appear in the display.
•Briefly press preset button 1, “000” will
appear in the display.
•Enter the code number given in the
Blaupunkt car radio passport:
Preset button 1 only allows to choose
“0” or “1”. The first “0” will not be dis-
played.
Example: the code number is 0521.
-Press preset button 1until “000” ap-
pears in the display.
-Press preset button 2five times,
“500” appears in the display.
-Press preset button 3twice, “520”
appears in the display.
-Press preset button 4once, “521”
appears in the display.
•To confirm the code number:
Press the upper part of the rocker
switch .
Your car radio is now ready for operation.
If three dashes appear again in the display,
you have entered a wrong code number.

Augsburg CR 24
18
Adjusting the station search
sensitivity
You can adjust the sensitivity of the automa-
tic station search.
For this,
• press lo.
When “lo” is visible in the display, then
only those stations with relatively strong
signals will be picked up (low sensitivi-
ty).
When “lo” is not visible in the display,
then stations with weaker signals will
also be picked up (high sensitivity).
Stereo - mono switch
You can switch to mono when the reception
conditions are only poor:
• Press lo for approximately 2 seconds.
During mono reception the stereo sign
will go out in the display.
Each time the car radio is switched on, the
reception will automatically be set to stereo.
The radio will automatically shift to mono
when the reception conditions are poor.
Changing the memory bank
YoucanshiftbetweenthememorybanksI,II,
III and T to store and recall the stored sta-
tions.
Theselectedmemorybankisindicatedinthe
display.
• Press FM•T until the desired memory
bank is indicated in the display (press
repeatedly if necessary).
Storing stations
For each memory bank (I, II, III, T) you can
store up to six stations using the preset
buttons 1, 2, 3, 4, 5, 6.
•Select the memory bank by pressing
FM•T.
•Use the rocker switch to tune in a stati-
on (either automatically or manually).
•Press the desired preset button and
hold it. First the station will be muted
and then becomes audible again (after
approximately 2 seconds).
Now the station has been stored in the re-
spective memory bank.
Theactivatedpresetbuttonisindicatedinthe
display.
Radio operation
With this car radio you can receive FM fre-
quencies ranging from 87.5 to 108 MHz.
Station search
• Press /, the car radio will then auto-
matically tune into the next station.
Ifyouholdthe upper orlowerpart / ofthe
rockerswitchdepressed,thesearchfunction
will forward quickly in the corresponding di-
rection.
Station search
up
down in
short intervals
down
up in
short intervals
Manual station search << >>
•Press << or >>, the frequency will then
move up or down in short intervals.
Ifyouholdtherockerswitchdepressed, then
the frequencies will move up or down more
quickly.

19
Augsburg CR 24
DEUTSCH
ENGLISH
ITALIANO
PORTUGUES NEDERLAND
ESPAGÑOL SVENSKA FRANÇAIS
Sampling stations briefly
with Radio-Scan
Startingwith the currently played stationyou
can sample the following ones one after
another for approximately 8 seconds each:
• Press knob 1for approximately 1 sec-
ond.
As soon as the following station is
found, it will be sampled for approxima-
tely 8 seconds. The corresponding fre-
quency starts flashing in the display; if
this station has been already stored,
then the corresponding preset button
and memory bank will also light up in
the display. When the sampling period
has elapsed, the radio will start sam-
pling the next station.
To keep on listening to a sampled station:
•Press knob 1once again.
The Scan function is off.
If no station is selected during the sampling
process, the set will start playing the station
from which the search operation has been
started before.
Note:
If you tune into a station which has already
been stored on another memory bank, the
corresponding preset button and the memo-
ry bank will start flashing on the display for
approximately 5 seconds.
Storing the strongest stations
automatically with Travelstore
In your respective reception area you can
automatically store the six strongest FM sta-
tions, sorted according to their frequencies.
This feature is particularly useful when you
are travelling.
• Press FM•T for at least 2 seconds.
The radio will search for the nearest FM
stations and store them in the memory bank
“T”(Travelstore).Whentheprocesshasbeen
completed, the first station will be set.
Ifyou wish,you canalso storestations in the
Travelstorememorybankmanually(see“Sto-
ring stations”).
Recalling stored stations
Youcanrecallanystoredstationbypressing
the corresponding button.
•Select the memory bank.
For this, press FM•T until the desired
memory bank is indicated in the dis-
play.
•Briefly press the corresponding preset.
Sampling stored stations briefly
with Preset-Scan
You can briefly sample all stored stations of
a memory bank using the Preset-Scan func-
tion.
• Press PS,
the set will sample all stations of the
selected memory bank I, II, III or “T”
briefly one after another.
Free preset buttons will be skipped.
To stop this function:
• Press PS once again.
The radio will continue to play the cur-
rently sampled station.

Augsburg CR 24
20
Automatic search start
(during cassette operation)
Ifyoushouldleavethereceptionareaofyour
ARI station while you are playing a cassette,
thenthe car radio will automatically tune into
a different station broadcasting the ARI si-
gnal.
If no such ARI station is found within appro-
ximately 30 seconds after the search functi-
onhasstarted,thecassettewillstopandyou
will hear a warning beep.
Switch the warning beep off as described
above.
Traffic messages (ARI)
ManyFMstationsbroadcasttrafficmessages
for their reception area at regular intervals.
StationsusingtheARIsystemalsobroadcast
an “ARI signal” during their programmes, so
that your car radio can recognize them.
Another signal is broadcast to indicate the
beginning and end of a traffic message.
Traffic messages are broadcast at a preset
volume, the level of which can be regulated
(see “Adjusting the volume for traffic messa-
ges and warning beep”). If you are playing a
cassette, it will be interrupted until the traffic
message has ended and will then resume
operation.
Switching the traffic messages
(ARI) on and off
If you want to switch the reception of traffic
messages (ARI) on and off,
• press ARI.
When the reception of traffic stations is
activated, “ARI” will light up in the dis-
play.
Now the radio will only pick up those stations
broadcasting an ARI signal.
Warning beep
Should you leave the reception area of the
stationyou aretuned to,then youwill hear a
warning beep after approximately 30 sec-
onds.
If you should press a preset button for a
station which does not broadcast the ARI
signal, then you will also hear a warning
beep.
Switching the warning beep off
a) Tune to a different station broadcasting
the ARI signal:
•Press the rocker switch 2or
•activate a preset button with a stati-
on that broadcasts the ARI signal.
or
b) Switch the traffic message priority off:
• Press ARI.
“ARI” goes out in the display.

21
Augsburg CR 24
DEUTSCH
ENGLISH
ITALIANO
PORTUGUES NEDERLAND
ESPAGÑOL SVENSKA FRANÇAIS
Tape operation
Inserting the tape
•Turn the set on.
•Insert a cassette.
Insert cassette with side A or 1
facing up, the open side facing
to the right.
Eject
cassette
The cassette will be played in the direction
used last.
Ejecting the cassette
• Press .
The cassette will be ejected.
Fast tape run
Fast forward
• Press FF (fast forward).
At the end of the tape, the set will
switch to the other track and start play-
ing.
Stop fast forward
• Press FR.
Fast rewind
• Press FR (fast rewind).
When the tape has rewound to the be-
ginning, the set will switch to play the
same track again.
Stop fast rewind
• Press FF.
Side A or 1 Side B or 2
Track indication
Switch-over to the other track
Press simultaneously
Fast
forward;
To stop: press FR
Fast
rewind;
To stop: press FF
Adjusting the volume for traffic
messages and warning beep
Thevolumefortrafficmessagesandwarning
beep has been preset at the factory. Howe-
ver, you can adjust it to suit your
personal needs.
•Tune into a traffic station (“SK” lights up
in the display).
Switch on the priority for traffic messages:
• Press ARI.
•Turn down the volume.
Slightlypulloutthe(connected)setandcare-
fully adjust the desired volume while a traffic
message is broadcast. Use an appropriate
screw driver with a maximum blade width of
3 mm.
ARI

Augsburg CR 24
22
Autoreverse function
(Switching tracks during playback)
• Press FR and FF at the same time.
At the end of the tape, the unit will automati-
cally switch to the other track.
Note:
If there is too much tension on the cassette
tape during playback, the set may switch to
theothertrackbyitself.Inthiscasecheckthe
condition of the tape. Sometimes it helps to
rewind the cassette tape completely.
Care of your audio equipment
We recommend that you use only C60/C90
cassettetapesinyourcarradio.Protectyour
cassettes from dirt, dust and temperatures
exceeding 50 °C.
During cold weather, allow cold cassettes to
warm up somewhat before playing them in
ordertoavoiduneventapetransport.Opera-
ting problems and sound distortions may
occur after approximately 100 hours of play-
ing time and are caused by dust particles
which adhere to the rubber roller and the
audio head.
Useacleanercassettetoremovenormaldirt
build-up.Ifmoredirtthan usual has accumu-
lated, use a cotton bud dipped in rubbing
alcohol to clean these parts. Never use any
hard tools.
Appendix
Technical data
Amplifier:
Output power: 2 x 10 W RMS power ac-
cording to DIN 45324/3.1
into 2 Ω
FM:
Sensitivity: 0.9 µV at 26 dB signal-
to-noise ratio
Frequency
response: 35 - 15 000 Hz (-3 dB)
Cassette:
Frequency
response: 40 - 14 000 Hz (-3 dB)
Subject to modifications!

13
Augsburg CR 24 (Code deaktiviert)
DEUTSCH
ENGLISH
ITALIANO
PORTUGUES NEDERLAND
ESPAGÑOL SVENSKA FRANÇAIS
Blaupunkt-Werke GmbH
Bosch Gruppe
7/94 K7/VKD 3 D93 162 014 PM