Blaupunkt BRISBANE SD48 7 648 000 310 User manual

Car Radio SD USB MP3 WMA
Brisbane SD48 7 648 000 310
Victoria SD48 7 648 001 310
Bedienungs- und Einbauanleitung
Operating and installation instructions
Mode d’emploi et de montage
Istruzioni d’uso e di installazione
Gebruiksaanwijzing en inbouwhandleiding
Bruks- och monteringsanvisning
Instrucciones de manejo e instalación
Instruções de serviço e de montagem
Betjenings- og monteringsvejledning
Instrukcja obsługi i montażowa
Návod k obsluze a k montáži
Návod na obsluhu a inštaláciu
Инструкция по эксплуатации и установке
www.blaupunkt.com
01_Brisb_VictoriaSD48_de.indd 101_Brisb_VictoriaSD48_de.indd 1 23.11.2007 16:12:19 Uhr23.11.2007 16:12:19 Uhr

7
18
4
1113
9
2 3 56
14 12 10
2
01_Brisb_VictoriaSD48_de.indd 201_Brisb_VictoriaSD48_de.indd 2 23.11.2007 16:12:21 Uhr23.11.2007 16:12:21 Uhr

1buttonforremovingthecontrolpan-
el (release panel)
2 Arrow buttons
3SRC button for source selection be-
tween Radio, SD, USB and CD changer
or AUX and FRONT-AUX (if connect-
ed).
4Button to switch the device on/off and
operate the volume mute feature.
5BND•TS button
Short press: Selects the FM memory
banks and the MW and LW wavebands.
Long press: Starts the Travelstore func-
tion.
6Volume control
7LCD display
8Keys 1- 5
9Slot for SD/MMC cards
:Front AUX-IN socket for connecting ex-
ternal audio sources (e.g. portable CD
players).
;DIS button
<ESC button
=TRAF•RDS button
Short press: Switches traffic informa-
tion standby on/off.
Long press: Switches convenient RDS
function on/off.
>MENU button
Short press: Calls up the menus for the
settings. Confirming menu settings.
Long press: Starts the scan function.
40
Controls
02_Brisb_VictoriaSD48_gb.indd 4002_Brisb_VictoriaSD48_gb.indd 40 23.11.2007 16:13:34 Uhr23.11.2007 16:13:34 Uhr

About these instructions..................43
Symbols used................................43
Use as directed..............................43
Declaration of conformity................43
For your safety ................................44
If you are installing device yourself....44
Observe the following!....................44
Cleaning instructions...................... 44
Disposal note ................................44
Scope of delivery.............................45
Optional equipment
(not part of the scope of delivery) ....45
Warranty.........................................46
Service ...........................................46
Detachable control panel .................47
Theft protection.............................47
Detaching the control panel.............47
Attaching the control panel..............47
Switching on/off..............................48
Switching on/off using button 4....48
Switching on/off via vehicle ignition... 48
Switching off with detachable
control panel.................................48
Timeout function .............................48
Adjusting the volume .......................49
Setting the power-on volume ...........49
Quickly reducing the volume (MUTE)....49
Switching the confirmation
beep on/off (BEEP)........................50
Muting during telephone mode ........50
Telephone Audio/Navigation Audio...50
Radio mode.....................................51
Adjusting the tuner.........................51
Switching to radio mode .................51
Convenient RDS functions...............52
Selecting the waveband/
memory bank................................52
Tuning into a station .......................53
Adjusting the sensitivity of
the station seek tuning (SENS) ........53
Storing stations .............................53
Storing stations automatically
(Travelstore) .................................54
Listening to stored stations .............54
Scanning receivable stations (SCAN) ...54
Setting the scanning time
(SCAN TIME).................................54
Programme type (PTY) ..................55
Configuring the display...................56
Traffic information...........................56
Switching traffic information
priority on/off ...............................56
Skipping a traffic announcement......57
Setting the volume for traffic
announcements.............................57
MP3/WMA mode .............................58
Preparation of an MP3/WMA
data carrier...................................58
Switching to MP3 mode..................59
Configuring the display...................60
Selecting a directory ......................60
Selecting tracks.............................60
Fast searching (audible)..................60
Repeating individual tracks or
whole directories (REPEAT).............60
Random track play (MIX).................61
Scanning tracks (SCAN)..................61
Interrupting playback (PAUSE).........61
41
ENGLISH
Contents
02_Brisb_VictoriaSD48_gb.indd 4102_Brisb_VictoriaSD48_gb.indd 41 23.11.2007 16:13:35 Uhr23.11.2007 16:13:35 Uhr

CD-changer mode............................62
Switching to CD-changer mode........62
Selecting CDs................................62
Selecting tracks.............................62
Fast searching (audible)..................62
Configuring the display...................62
Repeating individual tracks or
whole CDs (REPEAT)......................62
Random track play (MIX).................63
Scanning all tracks on all CDs (SCAN)...63
Interrupting playback (PAUSE).........63
Clock Time ......................................64
Displaying the time ........................64
Setting the time.............................64
Selecting 12/24-hour clock mode....64
Displaying the time with device
and ignition switched off.................64
Sound .............................................65
Equalizer ......................................65
Setting the left/right volume
distribution (BALANCE)..................68
Adjusting the front/rear volume
distribution (FADER)...................... 68
Equalizer presettings (PRESETS) .....68
X-BASS ...........................................69
Adjusting the X-BASS boost.............69
Adjusting E-XBASS.........................70
Display............................................71
Adjusting the display brightness.......71
Setting the display illumination
colour ..........................................71
External audio sources.....................73
Rear AUX-IN input ..........................73
Front AUX-IN socket ....................... 74
Mixing an external audio source with
another audio source (MIX AUX)....... 74
Factory settings (Normset)...............75
Technical data .................................76
Installation instructions .................484
42
Contents
02_Brisb_VictoriaSD48_gb.indd 4202_Brisb_VictoriaSD48_gb.indd 42 23.11.2007 16:13:35 Uhr23.11.2007 16:13:35 Uhr

About these instructions
These instructions contain important
information to easily and safely install
and operate the device.
Read these instructions carefully and
completely before using the device.
Keep the instructions at a location so
that they are always accessible to all
users.
Always pass on the device to third par-
ties together with these instructions.
In addition, observe the instructions of the
devices used in conjunction with this de-
vice.
Symbols used
These instructions employ the following
symbols:
DANGER!
Warns about injuries
DANGER!
Warns about accidents
DANGER!
Warns about hearing loss
The CE mark confirms the com-
pliance with EU directives.
Identifies a sequencing step
Identifies a listing
•
•
•
•
쏅
•
Use as directed
This device is intended for installation and
operation in a vehicle with 12 V vehicle sys-
tem voltage and must be installed in a DIN
slot. Observe the 'performance limits in the
technical data. Repairs and installation, if
necessary, should be performed by a spe-
cialist.
Declaration of conformity
The Blaupunkt GmbH declares that the de-
vices Victoria SD48 and Brisbane SD48
comply with the basic requirements and
the other relevant regulations of the direc-
tive 89/336/EWG.
43
ENGLISH
About these instructions
02_Brisb_VictoriaSD48_gb.indd 4302_Brisb_VictoriaSD48_gb.indd 43 23.11.2007 16:13:35 Uhr23.11.2007 16:13:35 Uhr

For your safety
The device was manufactured according to
the state of the art and established safety
guidelines. Even so, dangers may occur if
you do notobserve the safetynotes in these
instructions.
If you are installing device
yourself
You may only install the device yourself if
you are experienced in installing car sound
systems and are very familiar with the elec-
trical system of the vehicle. For this pur-
pose, observe the installation instructions
at the end of these instructions.
Observe the following!
DANGER!
Increased risk of injury from
connector
In case of an accident, the protruding con-
nector in the front AUX-IN socket may cause
injuries. The use of straight plugs or adapt-
ers can lead to an increased risk of injury.
For this reason, we recommend using
angled jack plugs, e.g. the Blaupunkt
accessories cable (7 607 001 535).
In operation
Operate the device only if traffic situa-
tion permits it! Stop at a suitable loca-
tion to perform extensive settings.
Remove orattachthecontrolpanelonly
while the vehicle is standing an.
•
•
•
To protect your hearing, always listen at
a moderate volume. During mute phas-
es (e.g. while the CD changer is chang-
ing the CD), changing the volume is not
detectable until after this mute phase.
Do not increase the volume during this
mute phase
Always listen at a moderate volume so
thatyoucanalwayshearacousticwarn-
ing signals (e.g. police).
After operation
The device is worthless to a thief with-
out the control panel. Always remove
the control panel whenever you leave
the vehicle.
Transport the control panel so that it is
protected against impacts and the con-
tacts cannot become dirty.
Cleaning instructions
Solvents, cleaning and scouring agents as
well as dashboard spray and plastics care
product may contain ingredients that will
damage the surface of the device. Use only
a dry or slightly moistened cloth for clean-
ing the device.
Disposal note
Do not dispose of your old unit in the
household trash!
Use the return and collection systems avail-
able to dispose of the old device.
•
•
•
•
44
For your safety
02_Brisb_VictoriaSD48_gb.indd 4402_Brisb_VictoriaSD48_gb.indd 44 23.11.2007 16:13:36 Uhr23.11.2007 16:13:36 Uhr

iPod/USB interface
The iPod interface or iPod/USB interface
allows connecting the iPod or iPod Mini to
the radio device and conveniently control-
ling the playback via the radio device. The
iPod/USB interface provides an additional
USB connection.
Amplifier
You can use all Blaupunkt and Velocity
amplifiers.
CD changers
You can connect the following Blaupunkt
CD changers:
CDC A 03, CDC A 08 and IDC A 09.
Scope of delivery
The scope of delivery includes:
1 Car sound system
1 Support frame
2 Disassembly tools
1 Guide pin
1 USB connecting cable
1 Operating instructions
Optional equipment
(not part of the scope of delivery)
Use only accessories approved by
Blaupunkt.
Remote control
The steering wheel and/or handheld re-
mote control allows you to access the most
important functions of your car sound sys-
tem safely and conveniently.
You cannot switch the device on/off using
the remote control!
You can find out from your Blaupunkt dealer
or on the Internet at www.blaupunkt.com
which remote controls can be used with
your car sound system.
Bluetooth/USB interface
ForBluetoothapplications,suchaswireless
hands-freecallingandBluetoothstreaming,
you can connect a Bluetooth interface. The
Bluetooth/USB interface provides an addi-
tional USB connection.
45
ENGLISH
Scope of delivery
02_Brisb_VictoriaSD48_gb.indd 4502_Brisb_VictoriaSD48_gb.indd 45 23.11.2007 16:13:36 Uhr23.11.2007 16:13:36 Uhr

Warranty
We provide a manufacturer's warranty
for products bought within the European
Union. For devices purchased outside the
European Union, the warranty terms issued
by our respective responsible domestic
agency are valid.
The warranty terms can be called up under
www.blaupunkt.com or requested directly
from:
Blaupunkt GmbH
Hotline
Robert-Bosch-Str. 200
D-31139 Hildesheim
Service
Insomecountries, Blaupunkt offersarepair
and pick-up service.
Information about the availability of this
service in your country can be found at
www.blaupunkt.com.
If you want to take advantage of this serv-
ice, you may request a pick-up service for
your device via the Internet.
Warranty Service
46
02_Brisb_VictoriaSD48_gb.indd 4602_Brisb_VictoriaSD48_gb.indd 46 23.11.2007 16:13:36 Uhr23.11.2007 16:13:36 Uhr

Detachable control panel
Theft protection
The device is equipped with a detachable
control panel (flip-release panel) to protect
your equipment against theft. The device
is worthless to a thief without this control
panel.
Protect your device against theft by taking
the control panel with you whenever you
leave your vehicle. Do not leave the control
panel inside your vehicle - not even in a hid-
ing place.
The control panel has been designed to be
easy to use.
Notes:
Never drop the control panel.
Never expose the control panel to di-
rect sunlight or other heat sources.
Avoid direct skin contact with the
control panel’s electrical contacts. If
necessary, clean the contacts with a
lint-free cloth moistened with clean-
ing alcohol.
•
•
•
Detaching the control panel
1
Press the button 1.
The locking mechanism of the control panel
is unlocked. The device switches off.
Pull the control panel straight out of the
device and to the left.
All the current settings are saved.
Attaching the control panel
Push the control panel into the guides
of the device from the left to the right.
Note:
Whenattachingthecontrolpanel,make
sure you do not push on the display.
Carefully push on the left side of the
control panel until it clicks into place.
쏅
쏅
쏅
쏅
47
ENGLISH
Detachable control panel
02_Brisb_VictoriaSD48_gb.indd 4702_Brisb_VictoriaSD48_gb.indd 47 23.11.2007 16:13:36 Uhr23.11.2007 16:13:36 Uhr

Switching on/off
There are various ways of switching the de-
vice on/off:
Switching on/off using button 4
To switch on the device, press button
4.
To switch off the device, press and
hold down button 4for longer than
two seconds.
The device switches off.
Note:
To protect the vehicle battery, the de-
vice will switch off automatically after
one hour if the ignition is off.
Switching on/off via vehicle
ignition
The device will switch on/off simultaneous-
ly with the ignition if the device is correctly
connected to the vehicle’s ignition and you
did not switch the device off and back on by
pressing button 4.
Switching off with detachable
control panel
Detach the control panel.
The device switches off.
쏅
쏅
쏅
Timeout function
The device features a time-out function
(time window). For example, if you press
the MENU button >and select a menu
item, the device switches back after ap-
prox. 8 seconds after the last button activa-
tion. The settings performed are saved.
Switching on/off Timeout function
48
02_Brisb_VictoriaSD48_gb.indd 4802_Brisb_VictoriaSD48_gb.indd 48 23.11.2007 16:13:36 Uhr23.11.2007 16:13:36 Uhr

Adjusting the volume
You can adjust the volume in steps from
0 (off) to 50 (maximum).
To increase the volume,
turn the volume control 6clockwise.
To decrease the volume,
turn the volume control 6counter-
clockwise.
Setting the power-on volume
You can set the power-on volume. You
can adjust it manually or select the "LAST
VOL" setting. If you enable "LAST VOL",
the volume which was set the last time you
switched off the device is re-enabled.
Press the MENU button >.
The display shows "MENU".
Press the or button 2repeatedly
until "ON VOLUME" appears on the dis-
play.
Press the button 2to manually ad-
just the power-on volume and
adjust the power-on volume using the
or buttons 2.
OR:
Press the button 2to select the
"LAST VOL" setting.
Whenyouhave finished making yourchang-
es,
press the MENU button >.
To exit the menu,
press the ESC button <.
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
Note:
To protect your hearing, the power-on
volume is limited to the value "38" for
the setting "LAST VOL". If the "LAST
VOL" setting is selected and the vol-
ume was set higher than "38" before
switch-off, the value "38" will be used
at switch-on.
Quickly reducing the volume
(MUTE)
You can quickly reduce the volume to a pre-
set level (Mute).
Briefly press button 4.
"MUTE" appears on the display.
Cancelling mute
To return to your previously set volume
level,
briefly press button 4again.
Adjusting the mute level
You can adjust the mute level.
Press the MENU button >.
The display shows "MENU".
Press the or button 2repeat-
edly until "MUTE LVL" appears on the
display.
Press the button 2to open the sub-
menu.
"MUTE" and the currently set value are dis-
played.
Adjust the mute level using the button
or 2.
쏅
쏅
쏅
쏅
쏅
쏅
49
ENGLISH
Adjusting the volume
02_Brisb_VictoriaSD48_gb.indd 4902_Brisb_VictoriaSD48_gb.indd 49 23.11.2007 16:13:36 Uhr23.11.2007 16:13:36 Uhr

Whenyouhave finished making yourchang-
es,
press the MENU button >.
To exit the menu,
press the ESC button <.
Switching the confirmation beep
on/off (BEEP)
The system will output a confirmation beep
for some functions if you keep a button
pressed down for longer than two seconds,
for instance, when assigning a radio station
to a station preset button. You can switch
the beep on or off.
Press the MENU button >.
The display shows "MENU".
Press the or button 2repeatedly
until"BEEPON"or "BEEP OFF" appears
on the display.
Press the button 2to call up the
submenu.
Switch the beep on or off using the
button 2. "OFF" means beep off,
"ON" means beep on.
Whenyouhave finished making yourchang-
es,
press the MENU button >.
To exit the menu,
press the ESC button <.
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
Muting during telephone mode
If your car sound system is connected with
a cell phone or navigation system, the car
soundsystemis mutedwhenacallis incom-
ing or during a voice output of the naviga-
tion. The call or the voice output is played
backvia the loudspeakersof thecardsound
system. In order for this feature to work, the
mobiletelephoneornavigationsystemmust
be connected to the car sound system as
described in the installation instructions.
You can find out from your Blaupunkt dealer
which navigation systems can be used with
your car sound system.
If a call is incoming or a navigation an-
nouncement takes place, the display shows
"TELEPHONE".
Telephone Audio/Navigation
Audio
During a telephone call or a voice output of
the navigation, no traffic announcements
are switched through.
You can set the volume level at which the
telephone calls or navigation announce-
ments are mixed in.
Press the MENU button >.
The display shows "MENU".
Press the or button 2repeatedly
until "TEL VOL" appears on the display.
Press the button 2to call up the
submenu.
"TELVOL" and the currently set value are
displayed.
Set the desired volume with the or
button 2.
쏅
쏅
쏅
쏅
50
Adjusting the volume
02_Brisb_VictoriaSD48_gb.indd 5002_Brisb_VictoriaSD48_gb.indd 50 23.11.2007 16:13:36 Uhr23.11.2007 16:13:36 Uhr

Whenyouhave finished making yourchang-
es,
press the MENU button >.
To exit the menu,
press the ESC button <.
Notes:
Ifthevolumelistenedtois higher than
the set "TEL VOL" value, telephone
calls or navigation announcements
are played back at the volume lis-
tened to.
Using the volume control 6, you can
adjust the volume for telephone calls
and navigation announcements di-
rectly during the playback.
쏅
쏅
•
•
Radio mode
Adjusting the tuner
To ensure proper functioning of the tuner,
the device must be set for the region in
which it is being operated. You can select
betweenEurope(EUROPE), America(USA)
and Thailand (THAI). The tuner is factory-
set to the region in which it was sold. If you
experience problemswith yourradiorecep-
tion, please check this setting.
The radio functions described in these op-
erating instructions refer to the tuner set-
ting EUROPE.
Switch off the device by pressing but-
ton 4.
Hold the buttons 18and DIS ;
pressed at the same time and switch on
the device again with the button 4.
The current setting is displayed.
Select your tuner region with the or
button 2.
To save the setting and to exit the menu,
press the MENU button >.
Switching to radio mode
If you are in SD, USB, CD changer or AUX-
IN mode,
press the BND•TS button 5
or
press the SRC button 3repeatedly
until "TUNER" appears on the display.
쏅
쏅
쏅
쏅
쏅
쏅
Adjusting the volume Radio mode
51
ENGLISH
02_Brisb_VictoriaSD48_gb.indd 5102_Brisb_VictoriaSD48_gb.indd 51 23.11.2007 16:13:37 Uhr23.11.2007 16:13:37 Uhr

Convenient RDS functions
This device is equipped with an RDS (Radio
Data System) radio receiver. Many FM sta-
tions broadcast a signal that not only car-
ries the programme but also additional
information such as the station name and
programme type (PTY).
The station name appears on the display as
soon as the tuner receives it.
The convenient RDS functions AF
(Alternative Frequency) and REGIONAL ex-
tend your radio’s range of functions.
AF: If the RDS function is activated, the
radio automatically tunes into the best
receivable frequency for the station
that is currently set.
REGIONAL: At certain times, some ra-
dio stations divide their programme
into regional programmes providing
different content. You can use the REG
function to prevent the car radio from
switching to alternative frequencies
that are transmitting different pro-
gramme content.
Note:
REGIONAL must be activated/deacti-
vated (REG ON/OFF) separately in the
menu.
Switching the RDS function on/off
If you want to use the RDS functions (AF
and REGIONAL),
press and hold down the TRAF•RDS
button =for longer than two sec-
onds.
The RDS function is active if RDS appears
on the display.
•
•
쏅
To deactivate,
press and hold down the TRAF•RDS
button =for longer than two sec-
onds.
The RDS symbol disappears from the dis-
play.
Switching REGIONAL on/off
Press the MENU button >.
The display shows "MENU".
Press the or button 2repeatedly
until "REG ON" or "REG OFF" appears
on the display.
Press the button 2to open the sub-
menu.
To switch REGIONAL on/off,
press the button 2.
Press the MENU button >.
To exit the menu,
press the ESC button <.
Selecting the waveband/memory
bank
This device can receive programmes broad-
cast over the FM frequency range as well as
the MW and LW (AM) wavebands. There are
three memory banks available for the FM
waveband (FM1, FM2 and FMT) and one
for each of the MW and LW wavebands.
Five stations can be stored in each memory
bank.
To switch between the FM memory banks
(FM1, FM2 and FMT) and the MW and LW
wavebands,
briefly press the BND•TS button 5.
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
52
Radio mode
02_Brisb_VictoriaSD48_gb.indd 5202_Brisb_VictoriaSD48_gb.indd 52 23.11.2007 16:13:37 Uhr23.11.2007 16:13:37 Uhr

Adjusting the sensitivity of the
station seek tuning (SENS)
You can choose whether the radio should
only tune into stations providing good re-
ception or whether it can also tune into
those with a weak reception.
Press the MENU button >.
The display shows "MENU".
Press the or button 2repeatedly
until "SENS" and the currently set value
appears on the display.
"SENS HI6" means that the tuner is set to
the highest sensitivity setting. "SENS LO1"
means it is set to the lowest sensitivity set-
ting.
Press the button 2to open the sub-
menu.
Set the desired sensitivity level using
the or button 2.
Whenyouhave finished making yourchang-
es,
press the MENU button >.
To exit the menu,
press the ESC button <.
Note:
You can set different sensitivity levels
for FM and AM (MW/LW).
Storing stations
Storing stations manually
Select the desired memory bank (FM1,
FM2, FMT) or one of the wavebands
(MW or LW).
Tune into the desired station.
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
Tuning into a station
There are various ways of tuning into a sta-
tion:
Automatic station seek tuning
Press the or button 2.
The radio tunes into the next receivable
station.
Tuning into stations manually
You can also tune into stations manually.
Note:
You can only tune into stations manu-
ally if the convenient RDS function and
RDY are deactivated.
Press the or button 2.
Browsing through broadcasting
networks (FM only)
If radio stations provide several pro-
grammes, you have the option of browsing
through these so-called "broadcasting net-
works".
Note:
The convenient RDS function and PTY
must be activated before you can use
this feature.
Press the or button 2to switch
to the next station on the broadcasting
network.
Note:
When using this feature, you will only
be able to switch to stations that you
have received once before already. To
receive the stations, use the Scan or
Travelstore function.
쏅
쏅
쏅
53
ENGLISH
Radio mode
02_Brisb_VictoriaSD48_gb.indd 5302_Brisb_VictoriaSD48_gb.indd 53 23.11.2007 16:13:37 Uhr23.11.2007 16:13:37 Uhr

Starting SCAN
Press and hold down the MENU button
>for longer than two seconds.
Scanning begins. "SCAN" and the station
name or the frequency appear intermittent-
ly on the display.
Cancelling the SCAN and continuing to
listen to a station
Press the MENU button >.
Scanning stops and the radio continues
playing the station that it tuned into last.
Setting the scanning time
(SCAN TIME)
Press the MENU button >.
The display shows "MENU".
Press the or button 2repeatedly
until "SCAN TIME" appears on the dis-
play.
Press the button 2to open the sub-
menu.
"SCAN" and the currently set value are dis-
played.
Set the desired scan time using the
or button 2.
Whenyouhave finished making yourchang-
es,
press the MENU button >.
To exit the menu,
press the ESC button <.
Note:
The adjusted scan time also applies to
scan processes in MP3/WMA mode.
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
Press and hold down one of the station
buttons 1- 58for longer than two
seconds to assign the station to that
button.
Storing stations automatically
(Travelstore)
You can automatically store the five sta-
tions offering the strongest reception in the
region (only FM). The stations are stored in
the FMT memory bank.
Note:
Any stations that were previously
stored in this memory bank are deleted
in the process.
Press and hold down the BND•TS but-
ton 5for longer than two seconds.
Thestoringprocedurebegins."FMTSTORE"
appears on the display. After the process
has completed, the radio will play the sta-
tion that is stored in memory location 1 of
the FMT memory bank.
Listening to stored stations
Select the memory bank or waveband.
Press the station button 1- 58of the
desired station.
Scanning receivable stations
(SCAN)
You can use the scan function to play all the
receivable stations briefly. You can set the
scanning time from 5 to 30 seconds in the
menu (in increments of 5 seconds).
쏅
쏅
쏅
쏅
54
Radio mode
02_Brisb_VictoriaSD48_gb.indd 5402_Brisb_VictoriaSD48_gb.indd 54 23.11.2007 16:13:37 Uhr23.11.2007 16:13:37 Uhr

Programme type (PTY)
Besides transmitting the station name,
some FM stations also provide informa-
tion on the type of programme that they are
broadcasting. Your car radio can receive
and display this information.
For example, the programme types can be:
CULTURE TRAVEL JAZZ
SPORT NEWS POP
ROCK CLASSICS
You can use the PTY function to select sta-
tions of a particular programme type.
PTY-EON
If you specify the programme type and start
seek tuning, the radio will switch from the
current station to a station of the selected
programme type.
Notes:
If the tuner does not find a station
that corresponds to the selected pro-
gramme type, you will hear a beep
and "NO PTY" appears briefly in the
display. The radio will then retune to
the station that it received last.
If the tuned radio station or another
station on the broadcasting network
broadcasts your selected programme
type at a later point in time, the radio
willautomaticallyswitchfromthecur-
rentlytunedstationorfromSDmode,
USB mode or CD-changer mode to
the station whose programme type
matches the one you selected.
If you do not want to use the PTY EON
switching, disable PTY. First, switch
to radio mode with the SRC 3or
BND•TS button 5.
•
•
•
Switching PTY on/off
The radio mode must be activated.
Press the MENU button >.
The display shows "MENU".
Press the or button 2repeatedly
until "PTY ON" or "PTY OFF" appears on
the display.
Press the button 2to display the
submenu.
Press the button 2to switch PTY
ON or OFF.
Whenyouhave finished making yourchang-
es,
press the MENU button >.
To exit the menu,
press the ESC button <.
Selecting the PTY language
You can select the language for the display
of the programme types. Options include
"DEUTSCH", "ENGLISH" and "FRANÇAIS".
Press the MENU button >.
The display shows "MENU".
Press the or button 2repeat-
edly until "PTY LANG" appears on the
display.
Press the button 2to display the
submenu.
The currently set language is displayed.
Setthe desiredlanguage using the or
button 2.
Whenyouhave finished making yourchang-
es,
press the MENU button >.
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
55
ENGLISH
Radio mode
02_Brisb_VictoriaSD48_gb.indd 5502_Brisb_VictoriaSD48_gb.indd 55 23.11.2007 16:13:38 Uhr23.11.2007 16:13:38 Uhr

To exit the menu,
press the ESC button <.
Selecting a programme type and
starting seek tuning
PTY must be activated (ON).
Press the or button 2.
The current programme type appears brief-
ly on the display.
During the display time, press the or
button 2to change to a different
program type.
Press the or button 2to start
seek tuning.
The radio will then tune into the next sta-
tion that it finds that corresponds to your
selected programme type. If the tuner does
not find a station that corresponds to the
selected programme type, you will hear a
beep and "NO PTY" appears briefly in the
display. The previously used frequency is
adjusted again.
Configuring the display
In radio mode, you have the option of dis-
playingthe stationnameorfrequencyof the
current station or the waveband or memory
bank and the time.
To switch between the display options,
press the DIS button ;.
쏅
쏅
쏅
쏅
쏅
Traffic information
Your device is equipped with an RDS-EON
receiver. EON stands for Enhanced Other
Network.Whenevera trafficannouncement
(TA) is broadcast, the system switches au-
tomatically from a station that does not pro-
videtrafficreportstotheappropriatetraffic
information station within the broadcasting
network that does.
Once the traffic announcement has been
played,thesystemwillswitchbacktothepro-
gramme that you were listening to before.
In addition, the device offers the option of
receiving traffic announcements even dur-
ing the operation of SD, USB, CD changer
and external sources (AUX-IN). For this pur-
pose, activate the priority for the traffic in-
formation.
Switching traffic information
priority on/off
Briefly press the TRAF•RDS button
=.
Thepriorityfortraffic announcements isac-
tivated if the display shows the traffic jam
symbol.
Notes:
You will hear a warning beep,
if you leave the reception area of a
traffic information station that the
system is tuned into while you are
in the SD, USB, CD changer or AUX
mode, and the subsequent automatic
seek tuning cannot find a new traffic
information station.
if you retune the radio from a traffic in-
formationstation to astation that does
not broadcast traffic information.
쏅
•
•
Radio mode Traffic information
56
02_Brisb_VictoriaSD48_gb.indd 5602_Brisb_VictoriaSD48_gb.indd 56 23.11.2007 16:13:38 Uhr23.11.2007 16:13:38 Uhr

If you hear the warning beep, you can
either switch off traffic information pri-
ority or tune into a station that broad-
casts traffic information.
Skipping a traffic announcement
"TRAFFIC" is displayed during a traffic an-
nouncement. To cancel a traffic announce-
ment without switching off the priority of
traffic information:
Duringthetrafficannouncement,press
the TRAF•RDS button =once.
The previously active audio source is played
again. If a traffic announcement is broad-
cast again, the device automatically switch-
es it through again.
Setting the volume for traffic
announcements
Press the MENU button >.
The display shows "MENU".
Press the or button 2repeatedly
until "TA VOLUME" appears on the dis-
play.
Press the button 2to open the sub-
menu.
"TA VOL" and the currently set value are dis-
played.
Set the desired volume using the or
button 2.
Whenyouhave finished making yourchang-
es,
press the MENU button >.
To exit the menu,
press the ESC button <.
쏅
쏅
쏅
쏅
쏅
쏅
쏅
Notes:
Ifthevolumelistenedtois higher than
the set volume for traffic announce-
ments, then traffic announcements
are played back one volume level
higher.
Using the volume control 6, you can
also adjust the volume during a traf-
fic announcement for the duration of
that announcement.
You can adjust the volume distribu-
tion for traffic announcements during
a traffic report. For further informa-
tion, please read the "Sound" chap-
ter.
•
•
•
57
ENGLISH
Traffic information
02_Brisb_VictoriaSD48_gb.indd 5702_Brisb_VictoriaSD48_gb.indd 57 23.11.2007 16:13:38 Uhr23.11.2007 16:13:38 Uhr