Blendtec Rapid Rinser User manual

www.commercial.blendtec.com | Rapid Rinser and Rapid Rinse Station
Owner’s Manual

2
Forgetscrubbingjars
forgetdowntime
Just like having someone else do it for you
rapid
rinser

3
SECTION 1 - IMPORTANT SAFEGUARDS�����������������������������������4
SECTION 2 - COMPONENT OVERVIEW ������������������������������������5
SECTION 3 - UNPACKING����������������������������������������������������5
SECTION 4 - INSTALLATION �������������������������������������������������6
SECTION 5 - OPERATING INSTRUCTIONS ���������������������������������6
SECTION 6 - SANITATION ����������������������������������������������������7
SECTION 7 - WARRANTY AND SERVICE �����������������������������������7
SECTION 8 - RAPID RINSE STATION����������������������������������������9
Table of Contents
RAPID RINSER
RAPID RINSE STATION

4
SECTION 1 – IMPORTANT SAFEGUARDS
Read all instructions carefully before using your Rapid Rinser�
1.1 HEALTH CERTIFICATION
The Blendtec Rapid Rinser and its accessories are certified by NSF International
(NSF), under Blendtec�
1.2 WATER HOSE PRECAUTIONS
▶ Do not operate with a damaged water hose or fitting�
▶ Should the water line or fitting become damaged, it should be replaced by a qualified
person to avoid hazard�
▶ Do not allow the water line to hang over the edge of the work surface�
▶ Always shut the water off at the source before cleaning, moving, or servicing�
1.3 TURN OFF THE WATER WHEN NOT IN USE
1.4 NEVER OPERATE THIS DEVICE WITHOUT A BLENDER JAR (OR
OTHER DRINK CONTAINER) IN PLACE
▶ Avoid contacting the spray nozzle while the system is pressurized�
▶ Never use the unit if it is not secured to the work surface with the suction cups provided
or used in the Rapid Rinse Station�
▶ Do not rinse cracked or broken glassware with this device�
1.5 NEVER OPERATE THE UNIT IF IT APPEARS TO BE DAMAGED
If the unit malfunctions, call Blendtec first� If it is dropped or damaged in any way, call
Blendtec Technical Support at 1�800�Blendtec (1�800�253�6383) to evaluate the extent of
damage and the possibility of either repair or replacement�
1.6 INSTALL UNIT WITH APPROPRIATE BACKFLOW PROTECTION
Backflow prevention must be installed to comply with federal, state or local codes that have
jurisdiction over the location�
1.7 DO NOT USE WATER THAT IS HOTTER THAN 120°F (48°C) IN THE
RAPID RINSER

5
SECTION 2 - COMPONENT OVERVIEW
2.1 EXTERNAL VIEW AND COMPONENTS
Refer to the lower left figure (Figure 1) below to identify the external components of the
rinser:
1� Spray nozzle
2� Rinser base
3� Water hose
4� Suction cups
5� 3/8” Compression fitting (Optional 3/8” BSPT adapter)
2.2 INTERNAL COMPONENTS
Refer to the lower right figure (Figure 2) below to identify the internal components of the
rinser:
1� Magnet
2� Spring
3� Upper shell
4� Nozzle vane
5� Nozzle
6� Lower shell
7� Water valve
SECTION 3 - UNPACKING
Save your packaging materials for future storage or return shipping� Save these instructions
for future reference�
3.1 UNPACKING YOUR RAPID RINSER
You should have received the following items in your package:
1� Rapid Rinser
2� Water hose
3� Owner’s manual
4� Rapid Rinse Station - Optional see section 8
5
3
1
2
6
4
1
4
3
2
5
Figure 1 Figure 2
7

6
Remove all components from shipping carton and verify all items were included in the box�
Check for any packing materials that may have blocked any of the openings of the Rapid
Rinser, the water hose or compression fitting� Inspect all items for possible handling damage,
immediately contact your Blendtec representative if there is evidence of broken or missing
parts�
3.2 RECORDING YOUR DATE OF PURCHASE / RECEIPT
Record below the date you received / purchased your Rapid Rinser� You will need this date
when contacting Blendtec for service�
Date of Purchase / Receipt _________________________
SECTION 4 - INSTALLATION
This equipment is to be installed with adequate backflow protection to comply with federal,
state, or local codes having jurisdiction�
4.1 PLACE THE RAPID RINSER IN THE SINK BASIN WHERE IT WILL BE
USED
Ensure the suction cups provided adhere to the basin floor (lightly moisten each cup with a
drop of water to facilitate suction)�
4.2 PLACE A BLENDER JAR (OR OTHER RINSABLE CONTAINER 8”
[20.3cm] WIDE OR SMALLER) OVER THE SPRAY NOZZLE
4.3 CONNECT THE WATER HOSE TO AN AVAILABLE WATER LINE
It is recommended that a certified plumber install the available water line with its own shut-
off valve�
4.4 TURN THE WATER ON
After the water line has been connected to the rinser, turn on the water supply� It is strongly
recommended that you use hot water following the requirements stated in section 1�7�
4.5 PRIME THE RINSER
Press the blender jar (or other rinsable kitchen container) down to activate the Rapid Rinser�
A steady spray of water should shoot from the nozzle into the blender jar� Release the
pressure on the blender jar to stop the flow of water� Should the above not work, contact
your Blendtec representative�
SECTION 5 - OPERATING INSTRUCTIONS
5.1 PLACE THE BLENDER JAR (OR OTHER RINSABLE KITCHEN
CONTAINER) UPSIDE DOWN ON THE RAPID RINSER BASE
5.2 TURN THE WATER ON TO ACTIVATE THE RAPID RINSER
5.3 FIRMLY PRESS THE BLENDER JAR DOWN TO ACTIVATE WATER
VALVE
5.4 RELEASE THE DOWNWARD PRESSURE WHEN THE JAR HAS BEEN
RINSED TO YOUR SATISFACTION

7
5.5 ONCE THE SPRAY OF WATER HAS SUBSIDED, REMOVE THE
RINSED BLENDER JAR AND ALLOW IT TO DRY IN THE INVERTED
POSITION
5.6 TURN THE WATER OFF WHEN THE RAPID RINSER IS NOT IN USE.
THIS WILL PREVENT ANY POSSIBILITY OF SPRAY WHEN A BLENDER
JAR IS NOT IN POSITION
SECTION 6 - SANITATION�
6.1 SHORT-TERM SANITATION
Shut off the water� Disconnect the water hose from the water source� Carefully pull the
Rapid Rinser away from the sink basin floor� Immerse the entire Rapid Rinser in a sink full of
sanitizing solution per the sanitizer’s manufacturer’s recommendation� Pull the Rapid Rinser
out of the sanitizing solution and rinse it completely with clean water� Allow the unit to dry�
Re-attach the water fitting to the water source�
6.2 LONG-TERM SANITATION
Shut off the water� Disconnect the water hose from the water source� Carefully pull the Rapid
Rinser away from the sink basin floor� Unscrew the spray nozzle from the bottom shell�
Carefully separate the two halves of the Rapid Rinser� DO NOT misplace the spring inside
the unit (see Figure 2)� Always clean and sanitize the unit as per the requirements of your
governing health department�
Thoroughly rinse the Rapid Rinser and all of its components after sanitation� Set the Rapid
Rinser and all of its components aside and allow them to dry completely� Reassemble the
Rapid Rinser by carefully placing the spring on top of the female threaded portion of the
water valve (Figure 2)� Place the top shell of the Rapid Rinser over the spring such that the
opening aligns with the spring� Insert the spray nozzle into the opening and thread until tight�
Replace the Rapid Rinser in the sink basin and reattach the water hose to the water source�
SECTION 7 - WARRANTY AND SERVICE
7.1 THE BLENDTEC RAPID RINSER IS WARRANTIED FOR A PERIOD
OF ONE YEAR FROM THE DATE OF PURCHASE / RECEIPT AGAINST
MANUFACTURING AND MATERIAL DEFECTS. THE STAINLESS STEEL
SPRAY NOZZLE HAS A LIFETIME WARRANTY
7.2 NOTE: OBVIOUS ABUSE OR MISTREATMENT OF THE RAPID RINSER
MAY VOID THE WARRANTY
7.3 SHOULD YOU NEED SERVICE, PLEASE CONTACT YOUR BLENDTEC
REPRESENTATIVE

8
forgetthe sink
Forget the mess
JUST let it do your dirty work
rapid
rinse
station

9
SECTION 8 – RAPID RINSE STATION
With the addition of the Rapid Rinse Station you will no longer need to place your Rapid
Rinser in a sink� With a water line and a drain line, you can put the Rapid Rinse Station in
the most convenient spot in the store� Most people like to put it right next to their Blendtec
blender to save time and make life smoother�
8.1 SPECIFICATIONS
DIMENSIONS: 20�2” L x 8�3” W x 6�5” H (51�3 cm x 21�1cm x16�5 cm)
WEIGHT: 5�3 lbs� (2�4 kg)
DRAIN CONNECTION: 3/4” Garden Hose Thread
8.2 DIRECTIONS
▶ Place the Rapid Rinser in the Rapid Rinse Station as shown below� If you already own the
Rapid Rinser, remove the four suction cups on the bottom before placing in the station�
▶ Connect a 3/4” garden hose drain line to the back of the rinse station and in accordance
with your local codes� We recommend using a licensed plumber for installation� Make sure
the drain line slopes away from the station since it is a gravityi-driven system�
▶ Do not allow the water line or drain line to hang over the edge of the work surface�
▶ Always shut the water off at the source before cleaning, moving, or servicing
FrontBack

10
8.3 CLEANING / SANITATION
▶ Using a mild soapy solution, wipe down all surfaces of the Rapid Rinse Station�
▶ Use clear, hot water to rinse the surfaces of the Rapid Rinse Station� A handheld spray
bottle will work best�
▶ To sanitize the surfaces of the Rapid Rinse Station either spray or wipe the surfaces of the
Rapid Rinse Station with the sanitizing solution diluted to the recommended level and left
on the unit per the manufacturer’s specification�
8.4 DRYING / STORAGE
▶ The area behind the Rapid Rinse Station is designed to store and dry your jars� See
picture below for example of how this works�

11

12
1206 South 1680 West
Orem, Utah 84058 U�S�A�
1-801-222-0888
commercial�blendtec�com
©2011 K-TEC, Inc�, All Rights Reserved� Blendtec is a registered trademark of K-TEC, Inc�
OWN-CE-070 Manual, Owner’s, Rapid Rinser and Rapid Rinse Station Rev 01 Jul 2011