to use your blender
1 Fit the sealing ring into the blade
unit.
2 Screw the jug onto the blade unit.
3 Put your ingredients into the jug.
4 Put the filler cap in the lid, then
turn.
5 Screw the lid onto the jug so that
the thumb tab is over the handle.
(To unscrew the lid, push the
thumb tab .)
6 Place the blender onto the power
unit and turn to lock .
7 Select a speed.
●Use speed 1 for lighter blending
eg. batters, milkshakes and
scrambled eggs.
●Use speed 2 for soups, sauces,
pâtés and mayonnaise.
OR
●Use the pulse control to operate
the motor in a start/stop action.
The pulse control operates the
motor and keeps it running for as
long as the lever is held down -
this will allow you to control the
texture of various foods eg. pâtés.
Important
blender and mill
●To ensure long life of your blender,
never run it for longer than 60
seconds or the mill for longer than
30. Switch off as soon as you’ve
got the right consistency.
●Don’t process spices – they may
damage the plastic.
●The machine won’t work if the
blender or mill is fitted incorrectly.
blender only
●Don’t put dry ingredients into the
blender before switching on. If
necessary, cut them into pieces;
remove the filler cap; then, with the
machine running, drop them
through one by one. Keep your
hand over the opening. Empty
regularly.
●Don’t use the blender as a storage
container. Keep it empty before
and after use.
●Never blend more than 11⁄2litres
(2 pts 12 fl.oz) – less for frothy
liquids like milk shakes.
mill only
Use for dry ingredients only.
hints
●When making mayonnaise, put all
the ingredients, except the oil, into
the blender. Then, with the
machine running, pour the oil into
the filler cap and let it run through.
●Thick mixtures, eg pâtés and dips,
may need scraping down. If it’s
difficult to process, add more
liquid.
●When crushing ice, add 15ml
(1 tbsp) water to 6 ice cubes.
Operate the blender in short
bursts.
to use your mill
1 Put your ingredients into the jar. Fill
it no more than half full.
2 Fit the sealing ring into the blade
unit.
3 Turn the blade unit upside down.
Lower it into the jar, blades down.
4 Screw the blade unit onto the jar
until it’s finger-tight.
5 Place the mill onto the power unit
and turn to lock.
6 Select a speed or use the pulse
control.
7 After milling, you can replace the
blade unit with the sprinkler lid and
shake out your food.
●The sprinkler lid is not airtight.
Use your blender for soups,
sauces, drinks, pâtés, mayonnaise,
dressings etc. Use your mill (if
supplied) for milling herbs, nuts
and coffee beans.
safety
●CAUTION: Blending very hot
liquids may result in hot
liquid and steam being
forced suddenly past the lid
or filler cap. Allow the liquid
to cool or reduce the
quantity and select a lower
speed if available. Protect
your hands with a cloth or
oven gloves when handling
the hot goblet and lid.
●Switch off and unplug:
●●before fitting or removing parts
●●after use
●●before cleaning.
●Keep hands and utensils out of the
blender when it’s on the power
unit.
●Don’t touch the sharp blades.
●Don’t let children or infirm people
use the machine unsupervised.
●Never use a damaged machine.
Get it checked or repaired: see
‘service’.
●Never use an unauthorised
attachment.
●Never leave the machine on
unattended.
●Don’t let children play with the
machine.
●When removing the blender or mill
from the power unit:
●●wait until the blades have
completely stopped;
●●don’t accidentally unscrew the
jug or jar from the blade unit.
●Only use the machine for its
intended domestic use.
before plugging in
Make sure your electricity supply is
the same as the one shown on the
underside of the machine.
Important – UK only
●The wires in the cord are coloured
as follows:
Blue = Neutral, Brown = Live.
●The appliance must be protected
by a 3A approved (BS1362) fuse.
Note:
●For non-rewireable plugs the fuse
cover MUST be refitted when
replacing the fuse. If the fuse cover
is lost then the plug must not be
used until a replacement can be
obtained. The correct fuse cover is
identified by colour and a
replacement may be obtained from
your Kenwood Authorised Repairer
(see Service).
●If a non-rewireable plug is cut off it
must be DESTROYED
IMMEDIATELY. An electric shock
hazard may arise if an unwanted
non-rewireable pug is inadvertently
inserted into a 13A socket outlet.
●This machine complies with
European Economic Community
Directive 89/336/EEC.
before using for the first
time
1 Remove all packaging.
2 Wash the parts: see ‘cleaning’.
key
blender
filler cap
lid
jug
sealing ring
blade unit
pulse control
speed control
power unit
cord storage
mill (if supplied)
blade unit
sealing ring
jar
sprinkler lid
