BlissLights PIXXI PX-1 User manual

User’s Guide
Model no. PX-1
Please ONLY use
manufacturer-provided
power supply
PIXXITM Laser Projector

TABLE OF CONTENTS
Notice ..............................................................................................................................1
Introduction ..................................................................................................................2
Before You Begin..........................................................................................................2
Parts List..........................................................................................................................2
Setting up the Laser Projector................................................................................3
List of Included Projections .....................................................................................3
Installation Tips ............................................................................................................4
Default Settings ...........................................................................................................4
Product Specications...............................................................................................4
Limited Warranty.........................................................................................................4
Troubleshooting ..........................................................................................................5
Caution............................................................................................................................5
Cleaning Instructions.................................................................................................5
Disposal...........................................................................................................................5

NOTICE
CAUTION—Use of controls or adjustments or performance of procedures other than those
specied herein may result in hazardous radiation exposure.
This laser product is certied as a Class 3R laser product and complies with FDA
performance standards for Laser Product Performance Standard (FLPPS) contained in the
regulations in 21 CFR Subchapter J.
Avoid direct eye contact of CLASS 3R laser energy as it can be hazardous. For reference,
the FLPPS requirements for demonstration laser products, like laser pointers, are limited
to CLASS 3R levels of laser energy. This product uses diractive optics to scatter the beam
energy. This scattering eect causes the energy concentration to drop below the exposure
limits for momentary or accidental viewing at a relatively short distance from the laser
aperture. As with all bright light-sources, when you operate this device in unsupervised
general public areas, it is recommended that up-close access to the light be restricted or
prevented.
This laser display device incorporates a CLASS 3B laser system which, by itself, may be
hazardous. However, this laser display device incorporates a protective housing in the
machine design so that there is no exposure or human access to laser radiation during
operation above the CLASS 3R limits. Each individual laser beamlet’s power is under 5 mW.
UNDER NO CIRCUMSTANCES shall attempts be made to open the protective housing or
operate the device if the aperture window is damaged.
All service to this laser display device requiring the protective housing to be opened and/
or removed shall be performed by service personnel or their authorized agents. Opening
the protective housing voids the warranty.
NO LASERS SHOULD BE POINTED INTO THE SKY WITHIN 10 NAUTICAL MILES
(18.5 km) OF AN AIRPORT. IF YOU ARE LOCATED WITHIN THIS SPECIFIC PERIMETER, WE
RECOMMEND THE LASERS BE POINTED DOWN AT THE GROUND SO NO STRAY BEAMS
ARE PROJECTED INTO THE AIR. CHECK WITH YOUR LOCAL AIRPORT OR PROVINCIAL
GUIDELINES FOR FURTHER INFORMATION.
1

INTRODUCTION
Thank you for purchasing the BlissLights PIXXI Laser Projector. This product is a unique
indoor/outdoor light xture that uses patented laser technology to project your favorite
images for year-round applications. We hope you enjoy this incredibly unique lighting
experience.
BEFORE YOU BEGIN
Immediately upon receiving the xture, carefully unpack and check the carton contents to
ensure that all parts are present and in good condition. Notify the retailer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the
carton itself shows signs of mishandling. Save the carton and all packing materials. In the
event that the xture must be returned, it is important that the xture be returned in the
original factory box. Please see parts list below for box contents.
PARTS LIST:
1. PIXXI Laser Projector
2. Tripod
3. Ground stake and 1/4-20 adapter
4. Remote Control
5. Power Adapter
6. Allen Key to adjust tripod
7. Cleaning cloth
8. Accessory carrying bag
2
1
3
2
5
6
4
MXK-013
+
-
Preset Timer
Reduce
Enlarge
PowerOrientation
Laser
ON/OFF
Off
60
120
180
240
78
Laser aperture
Safety label

1. Connect the power supply into an available standard electrical outlet.
2. Place the PIXXI on a at solid surface and aim toward desired ceiling/wall/tree.
3. Aim the remote control at the front window and press the POWER button.
4. To change the illumination angle on projection surfaces, adjust any leg of the tripod. If
tripod is loose, use the supplied Allen Wrench to tighten the screw on the underside of the
tripod screw-in knuckle.
5. Use the following buttons to control lighting eects:
a. Power – Use this button to turn the power on and o.
b. Orientation – use this button to rotate the image 90 degrees.
c. Enlarge – use this button to make the image bigger.
d. Reduce – Use this button to make the image smaller.
e. Right Arrow – use this button to select the next image projection.
f. Left Arrow – use this button to select the pervious image projection.
6. By default, the Pixxi will run continuously. The Preset Timer button sets a timer, which will
turn Pixxi o after a designated time. Press the button once to set the play time for an hour.
Double, triple, or quadruple press for 2, 3, or 4 hours respectively. Press and hold the button
for continuous play.
3
SETTING UP THE LASER PROJECTOR
LIST OF INCLUDED PROJECTIONS
Pixxi Dust
01. Bounce 1
02. Duet
03. Triplet
04. Bounce 2
05. Swirl 1
06. Sparkle 1
07. Sparkle 2
08. Sparkle 3
09. Swirl 2
10. Hovering reies
11. Pixxi show
(~2 min)
Abstract
12. Abstract 1
13. Abstract 2
14. Abstract 3
15. Abstract show
(~2 min)
16. Rain
Valentine’s Day
17. Love
18. Heart
19. Wedding
20. Flying hearts
21. Wedding bells
Occasions
22. Anniversary
23. Congratulations
24. Confetti
25. Graduation
Spring Holidays
26. Clovers
27. Pot of Gold
28. Bunny
29. Rabbit
30. Mother’s Day
31. Father’s Day
32. 4th of July
Birthday
33. Happy Birthday
34. Birthday show
(~2 min)
35. Birthday dino
36. Unicorn
37. Birthday car
38. Dump truck
39. Dance show
Halloween
40. Jack O’Lantern
41. Bats
42. Monster
43. Scary Eyes
44. Halloween show
(~4 min)
45. Falling leaves
46. Fire
Thanksgiving
47. Thanksgiving
48. Turkey
Hanukkah
49. Menorah
50. Happy
Hanukkah
51. Star of David
Christmas
52. Happy Holidays
53. Merry Christmas
54. Santa
55. Stocking
56. Snowman
57. Reindeer
58. Snowglobe
59. Santa sleigh
60. Penguin skater
61. Running deer
62. Christmas show
(~4 min)
New Year
63. Happy New Year
64. Firework
65. Champaigne
66. New Year show
(~2 min)
Misc
67. Basketball
68. Football
69. Soccer
70. Hockey
71. Golf
72. Surng
73. Undersea show
(~2 min)

1-YEAR LIMITED WARRANTY
This product carries a one (1) year warranty against defects in workmanship and materials. BlissLights,
LLC agrees to replace the defective product free of charge within the stated warranty period, when
returned by the original purchaser with proof of purchase. This product is not guaranteed against
wear or breakage due to misuse and/or abuse. For more detailed warranty information, please visit
www.blisslights.com/warranty
4
PRODUCT SPECIFICATIONS
Laser Classication Class 3R
Laser Wavelength 507 nm—Green
Housing Metal and ABS plastic
Power Consumption Less than 30 W
Power Input 120 V AC
Power Output < 5 mW per beamlet
Operation Indoor/Outdoor
Operating Temperature 32°F to 104°F (0°C to 40°C)
Maintenance Maintenance Free
Dimensions 6.5”L x 2.5”W x 6.5”H
Cord Length 3 ft (1 m)
Warranty Limited One Year
INSTALLATION TIPS
• Do not connect the light to a dimmer pack, as a dimmer accessory may damage
the laser component.
• Use only the manufacturer-provided CUL power supply.
• Limit the use of extension cords. If you need an extension cord, use only UL, CUL, or
CSA approved 3rd party extension cords.
• The darker the display area, the brighter your projection will appear. Try to avoid
display areas with strong ambient light sources, such as commercial street lights or
bright security ood lights.
DEFAULT SETTINGS
Once the laser projector is plugged in, it will enter the default mode where all eects
are on. Use the buttons to change the eect settings and brightness. This light runs
continuously by default, but has a built-in timer that can set the light to shut o after an
increment of 1 hour, 2 hours, 3 hours, or 4 hours.

CAUTION
This is not a toy. Young children must be supervised while using this device at all times.
TROUBLESHOOTING
We are always happy to help! To talk to a helpful team member, send an email to support@blisslights.
com or call our support line at 888-868-4603.
CLEANING INSTRUCTIONS
Surface clean only with a soft, dry cloth. Unplug unit before cleaning.
DISPOSAL
At the end of its serviceable life, this product should not be treated as household or general waste. It
should be handed over to the applicable collection point for the recycling of electrical and electronic
equipment.
5
Designed in the USA
By BlissLights LLC
Made in USA

6
www.blisslights.com