ROLY RL-S380X User manual

Operating Manual
Laser projector
Thank you for purchasing this product.
Before using this product, please read this manual carefully, and save this
manual for future use.

Table of Contents
Important safety notice 1
Precautions for use 8
Part name and function 12
Terminal panel 13
Top control panel 14
Indicator 15
Remote control 16
Remote control operating range 17
Placing the projector 18
Front leg adjusters 18
Connecting the device 19
Network connection 20
Connecting the AC power cord 21
Turn ing on the projector 22
Projection method 25
How to operate the on-screen menu 26
Menu bar 27
Auto setup function 28
Keystone correction 29
Volume adjustment 31
Remote control operation 31
Freeze button 31
Input source button 31
Auto setup button 31
Energy saving button 31
Black screen button 32
Timer button 32
Image mode button 32
Aspect ratio button 32
Display button 32
Menu operation 33
Direct operation 33
Auto adjustment 34
Horizontal position 34
Vertical position 34
Phase adjustment 35
Image display mode 35
Clock adjustment 35
Screen size adjustment 36
Image display mode 36
Video system selection 37
Setup 38
Network control use 44
Security password 45
Cleaning the projector 46
Air filter cleaning 47
Air filter replacement 49
Specification parameters 50
Dimensions 51
Ceiling moun hole 51
Compatible input signal *1 52
Compatible input signal *2 53
Appendix 54

1
Important safety notice!
Warning ：
This equipment must be grounded.
Warning ：
To prevent damage that may result in fire or electric shocks, do not expose
this appliance to rain or moisture.
This device cannot be used in a direct field of view in a visual display workplace.
To avoid causing disturbing reflections in the visual display workplace, it is strictly
forbidden to place this device in the direct field of view.
According to ISO 7779, the sound pressure intensity at the operator's position
is equal to or less than 70 dB (A).
Warning ：1. When not using the device for an extended period of time, be sure to
disconnect the power plug from the power outlet.
2. To avoidelectric shocks, do not open the cover. Please contact a qualified
personfor repairs.
3. Do not remove the grounding pin on the power plug . This device is equipped
with a two-pin grounding type power plug. This plug will only fit a grounding-type
power outlet. This is a security function. If you are unable to insert the plug into
the outlet, contact an electrician. Do not defeat the purpose of the grounding plug.
This device complies with the Class A standard of CISPR32.
This is a Class A information technology equipment. When used in a residential
environment, it may cause radio frequency interference. In this case, the user
will be required to take some appropriate countermeasures.
Precautions: To assure continued compliance , follow the attached installation
instructions. Including: When connecting to a computer or peripheral
device, the attached power cord and shielded interface cables must be
used. In addition, any unauthorized changes and modifications to this
equipment could void the user's authority to operate this device.
Warning ：To avoid fire or electric shocks, do not expose this product to rain or moisture.
Warning ：Risk of electric shock, do not open
Marks on the projector
The lightning flash with arrowhead symbol, within an equilateral triangle
on the projector is intended to alert the user to the presence of uninsulated
[dangerous voltage] inside the product, which poses a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
Important safety tips
Warning ：

Important safety tips!
2
Warning: Do not look directly ino the light emitted from the lens while using the
projector.
Mark on the projector
Laser statement: This projector falls into the Class I laser products of IEC/EN
60825-1:2014.
2.This projector is comply with Class II laser products of IEC
64271-5: 2015
3.According to GB72471-2012“Safety of Laser Products Part 1:
Classification of equipment, Requirements”this product comply
with Class II laser products.
Precautions: Using control, adjustment, or executive programs other than those
specified herein may result in the release of harmful radiation.
Precautions:
Do not remove
This device is equipped with a two-pin grounding type power plug. Do not remove the
grounding pin on the power plug. This plug will only fit a grounding-type power outlet.
This is a safety feature. If you are unable to insert the plug into the outlet, contact an
electrician. Do not defeat the prupose of the grounding plug.
Emergency treatment method:
To prevent damage to users and others and loss of life and property, if an abnormality
occurs, immediately unplug the power plug and stop using it.
Taiwan-specific empty battery recycling logo
Recycle empty batteries
1類雷射產品
1類雷射產品

Insert the power plug securely into the wall outlet and ensure that the power connector is
securely plugged into the projector.
If the plug is not inserted correctly, electric shocks or overheating will result.
Do not use a broken power plugs which are damaged or wall outlets which are coming
loose from the wall.
When the hands are wet, do not touch the power plug or the power connector. Otherwise,
it will easily lead to electric shocks.
Do not overload the wall outlet.
If the power supply is overloaded (for example: inserting too many power plugs),
overheating may occur and fire will result..
Clean the power plug regularly to to prevent it from becoming covered in dust..
Failure to observe this will cause a fire.
If dust builds up on the power plug, the resulting humidity can damage the insulation.
Caution: If the device on the side of the power outlet is not grounded with the provided
power cord, it may lead to electric shocks.
Important safety tips!
3
Warning:
Power
The wall outlet or the circuit breaker shall be installed near the equipment and shall be
easily accessible when problems occur.. If the following problems occur, cut off the
power supply immediately.
Continued use of the projector in these conditions will result in fire or electric shocks or
visual impairment.
If foreign objects or water gets inside the projector, cut off the power supply.
If the projector is dropped or the cabinet is damaged, cut off the power supply.
If you notice smoke, strange smell, or noise coming from the projector, cut off the
power supply.
Please contact an Authorized Service Center for repairs. Do not attempt to repair the
projector yourself.
During a thunderstorm, do not touch the projector and cables. Electric shocks can result.
Do not do anything that might damage the power cord or the power plug. If the power
cord is used while damaged, electric shocks, short circuits, or fire will result.
Do not damage the power cord, make any modifications to it, bend it excessively, twist it,
pull it, or wrap it into a bundle, or place it near any hot objects or place heavy objects on
top of it.
Do not use the anything other than the ptovided power cord. Otherwise, it may result in
electric shocks or fire.

Important safety tips!
4
On use/installation
Do not place the projector on soft materials such as carpets or sponge mats. Doing so
will cause the projector to overheat, which can cause burns, fire, or damage to the projector.
Do not set up the projector in humid or dusty places, or in places where the projector
may come into contact with oily smoke or steam.
Using the projector under such conditions will result in fire, electric shocks, or components
deterioration. Oil may also deform the plastic and the projector may fall down, such as
when mounted on the ceiling.
Do not install the projector in a place which is not strong enough to take the full weight
of the projector or on top of a surface which is sloped or unstable. Failure to observe this
will cause the projector to fall down or tip over the projector, and personal injury or
equipment damage could result.
Do not install the projector in a place where people can pass.
People may bump into the projector or trip over the power cord, which may result in fire,
electric shocks, or injury.
Warning:
Do not cover the air intake/ the air exhaust port. Doing so will cause the projector to
overheat, which can cause fire or damage to the projector.
●Do not place the projector in narrow, badly ventilated places.
●Do not place the projector on cloth or papers, as thses materials could be easily
drawn into the air intake port.
●Keep at least 1m (39-3/8'') between the air exhaust port and any wall or object,
and keep at least 50cm (19-11/16'') between the air intake port and any wall or object.
Do not look or place your hands directly into the lights emitted from the lens, while the
projector is being used.
Do not use optical devices such as magnifiers or mirrors to enter the projection beam.
Doing so can cause burns or impaired vision.
●Strong light is emitted from the projector’s lens. Do not look or place your
hands directly into this light.
●Be especially careful not to let children look into the lens. In addition, turn off
the power and disconnect the power plug when you are away from the projector.
Never attempt to remodel or disassemble the projector.
High voltage can cause accidents such as fire or electric shocks.
●For any inspection, adjustment and repair work, please contact an Authorized
Service Center.
Avoid metal objects, flammable materials or liquids entering into the projector.
Do not get the projector wet. Otherwise, it may cause a short circuit or excessive
temperature, thus resulting in accidents such as fire, electric shocks, etc. or projector failure.
●Do not place liquid containers or metal objects near the projector.
●If liquid gets inside the projector, consult your distributor.
●Please pay special attention to children.
Use an authorized ceiling mount bracket.
Using an unauthorized ceiling mount bracket may cause the machine to fall.
●Install the attached safety cables on the ceiling mount bracket to avoid dropping of the

Important safety tips!
5
Installation work should only be carried out by a qualified technician, such as lifting
the projector to the ceiling.
Improper fixing during installation may result in personal injury or electric shocks.
●Accessories
Do not use or handle the batteries improperly, and refer to the instructions below.
Failure to observe this will cause burns, batteries to leak, overheat, explode, or catch fire.
●Do not use unspecified batteries.
●Do not charge dry cell batteries.
●Do not disassemble dry cell batteries.
●Do not heat the batteries or place them into water or fire.
●Do not allow the + and - terminals of the batteries to come into contact with metallic
objects such as necklaces or hairpins.
●Do not store or carry batteries with metallic objects.
●Store the batteries in a plastic bag and keep them away from metallic objects.
●Make sure the polarities (+ and -) are correct when inserting the batteries.
●Do not use a new battery together with an old battery or mix different types of batteries.
●Do not use batteries with the outer cover peeling away or removed.
If the battery fuild leaks, do not touch it with bare hands and take the following measures
if necessary.
●Battery fuild on your skin or clothing could recult in skin inflammation or injury. Rinse
with clean water and seek medical advice immediately.
●Battery fuild coming in contact with your eyescould recult in loss of sight. In this case, do
not rub your eyes. Rinse with clean water and seek medical advice immediately.
Do not allow children to reach the batteries.
Accidental swallowing of accessories can harm your body.
●If swallowed, seek medical advice immediately.
Remove the empty batteries from the remote control immediately.
●If the emptybatteries are left in the remote control, it may cause the batteries fluid to
leak, the internal temperature to rise abnormally, or even explode.
Precautions
●Power
When disconnectingthe power cord, hold the plug and power connector.
If the power cord is pulled, the lead will become damaged and fire, short circuits, or serious
electric shocks will result.
When not using the projector for an extended period of time, disconnect the power plugfrom
the wall outlet. Failure to observe this may result in fire or electric shocks.

6
Turn off the power and disconnect the power plug from the wall outlet before replacing
the projector lens.
●Accidental projections may cause eye damage.
●If the projector lens is replaced without disconnecting the power plug, electric shocks
will result.
Disconnect the power plug from the wall outlet before cleaning or replacing any components.
Electric shocks can result if this is not done..
●On use/installation
Do not place any heavy objects on top of the projector. Otherwise, it may cause the projector
to become unstable or fall, and result in personal injury or equipment damage, and the
projector will be damaged or deformed.
Do not put your weight on the projector. You could fall or the projector could break,
and personal injury will result.
●Do not allow children to stand or sit on the projector.
Do not place the projector in extremely hot locations. Doing so will cause the outer casing
or internal components to deteriorate, or result in fire.
●Take particular care in locations exposed to direct sunlight or near electric heater accessories.
When moving the lens, do not put your hand into the opening next to the optical lens.
Doing so may result in injury.
Do not place the projector in locations that may be affected by salt or corrosive gases.
Failure to observe this may result in falling due to corrosion. In addition, corrosion can
also cause failure.
When using the projector, do not stand in front of the lens. Doing so may cause damage
and burn clothes.
●The projector lens emits strong light.
When using the projector, do not place objects in front of the lens. Do not place objects
in front of the projector lens to avoid blocking the projection. Failure to observe this may
result in fire or object damage and may cause projector failure.
●The projector lens emits strong light.
Unplug all cables from the projector before moving the projector. Moving the projector
without unplugging the cables may damage the cables, thus resulting in fire or electric
shocks.
When installing the projector on the ceiling, do not allow the mounting screws and power
cord to come into contact with the metal components inside the ceiling. Contact with
metal components inside the ceiling may result in electric shocks.
Important safety tips!

7
Accessories
When not using the projector for an extended period of time, remove the
batteries from the remote control. Failure to observe thiswill cause the batteries
to leak, overheat, catch fire or explode, which may result in fire or contamination
of the surrounding area.
Important safety tips!

Important safety tips!
8
Lens protection material
To protect the projector lens from vibration during handling, the lens protection material
has been covered to the product at the time of purchase. Remove the lens protection
material before use and save it for future use. Move the lens to its original position and
cover it with the lens protection material when handling.
Lens protection material
Handling precautions
When handling the projector, hold the bottom of the projector to avoid excessive
vibration and impact. This can damage internal components and result in malfunctions.
When handling the projector, the front leg adjusters should be retracted, otherwise the
front leg adjusters may be damaged.
●Do not set up the projector outdoors. The projector is designed for indoor use only.
●Avoid setting up the projector in the following places.
●Placeswhich are subject to vibration and shocks: For example, in a vehicle such as a car.
Failure to observe this may damage internal parts or cause equipment failure.
●Places close to the sea or where corrosive gases may be present. The projector may
malfunction due to corrosion and the component life may be shortened, resulting in
malfunctions.
●Places near the air conditioning exhaust vent: Depending on the conditions of use, the
image may be affected by the high temperature air discharged from the exhaust vent or
the hot and cold air discharged from the air conditioner, and rare jitter occurs. Make sure
that the exhaust from the projector or other equipment or the air from the air conditioner
do not blow directly into the front of the projector.
●Places which are subject to sudden temperature changes: For example, near the light source
(the lamp). The service life of the light source may be shortened, or the projector may
malfunction due to deformation caused by hot air. The operating ambient temperature
of the projector should be followed.
●Places near high voltage cables or near motors: The projector may be exposed to
interference if doing so.
●Installation work such as installing the projector to the ceiling should be done by a qualified
technician or distributor. To ensure the performance and safety of the projector, when
installing it to the ceiling or high, it should be done by a qualified technician or distributor.
●Install the connection cable by a qualified technician or distributor. If the cable transmission
characteristics cannot be achieved due to improper installation, image and sound interruption
may occur.
●If there are strong radio waves from radio stations or radios around, the projector may
not function properly.If there are any facilities or equipment near the installation location
that output strong
Safety Precautions

Important safety tips!
9
radio waves, install the projector away from such radio sources. In addition, you can use
a piece of metal foil or a metal conduit that is grounded at both ends to warp the regional
network cable connected to the terminal
●Lens focus adjustment
The high clarity projector lens is easily affected by the light from the light source, making
the focus unstable in the period just after switching on. It is recommended to adjust the
lens focus after continuing to project the image for at least 30 minutes.
●Do not install the projector at an elevations 2,700M (8858”) or higher above sea level.
●Do not use the projector in places where the ambient temperature is above 45°C (113°F).
Using the projector in places where the altitude is too high or the operating environment
is too hot may shorten the service life of the components or cause equipment failure.
●Precautions when installing the projector
●The front leg adjusters are only used to mount on the floor and adjust the angle. Use
it for other purposes may damage the projector.
●When installing the projector, use the four screws of the ceiling mount bracket to
secure the projector, in addition to floor or ceiling installation with the front leg adjusters.
●(screw diameter: M4, screw hole depth inside the projector: 10mm (15/32’’),
●Screw locking torque: 4 ± 0.5 N.m.
Screw holes for
ceiling installation (M4)
Screw holes for
ceiling installation (M4)
Front leg adjusters
Front leg adjusters
Position of screw holes for ceiling installation and front leg adjusters
RL-A400X
RL-A500X
RL-A400W
RL-A500W
RL-A500U
RL-S380W
RL-S600W
RL-S380X
RL-S600X
RL-S380U
RL-S600U

Important safety tips!
10
Do not stack multiple projectors.
●Do not use the projector with the top as the support.
●Do not block the projector's ventilation openings (air intake and exhaust ports).
●Avoid blowing hot and cold air from the air conditioning system directly to the ventilation
openings (air intake and exhaust ports) of the projector.
●Do not install the projector in a confined space.
If the projector must be installed in a confined space, air conditioning or ventilation should
be installed separately. Accumulated waste heat may trigger the projector's protective
circuit when ventilation is poor.
●The company shall not bear any responsibility for any damage to the product due to
improper selection of the installation site, even if it is within the effective warranty period.
Safety
When using this product, take safety measures for the following events.
●Personal information being leaked via this product.
●Unauthorized operation of this product by a malicious third party.
●Interfering or stopping of this product by a malicious third party.
●Take adequate security measures.
●Try to set a password that is difficult to guess.
●Change the password regularly.
●The company and its affiliates do not directly inquire customers about passwords. Do not
say the password when receiving such information.
●The connecting network must be secured by a firewall or other software.
●Set a password for network control and place restrictions on the users who can log in.
Disposal
When discarding the product, please contact your local authorities or distributor and ask
for the correct product disposal method. In addition, do not disassemble this product when
discarding it.
Storage
Store the projector in a dry room.
Precautions for use
●In order to get the picture quality
When you create a suitable environment, you can see excellent pictures with higher contrast
ratio. Pull down the curtains or blinds and turn off any lights near the screen to prevent outside
light or light from indoor lamps from shining onto the screen.
●Do not touch the surface of the projector lens with you bare hand.
If the surface of the projector lens becomes dirty from fingerprints or anything else, this will
be magnified and projected onto the screen.
●LCD panel
LCD panels are precision-made, but in rare cases, pixels could be missing or always lit.

Important safety tips!
11
Please note that these phenomena are not failures.
In addition, when the same image is projected for long periods of time, the afterimage
may remain on the LCD panel, in which case the entire white picture may appear for 1 hour
or longer. Please note that the afterimage may not disappear completely.
Optical components
When used in environments with high ambient temperature or large amounts of dust or
cigarette smoke, the replacement cycle of optical components such as LCD panels or
polarizers may be reduced, even after less than one year of use. For more information,
consult your distributor.
Light source
The light source of this projector is laser.
●Computer and external device connection
When connecting a computer or an external device, read this manual carefully for details
on the use of the power cord and shielded cable.
Information on Disposal in other Countries outside the European Union
Such symbols are valid only in the EU. If you wish to discard this
product, contact your local authorities or distributor to get the proper
disposal method.
Restricted substance content indication
Pb Hg Cd Cr+6
PBB PBDE
—
—
—
1.
2. —
Unit Lead Mercury Cadmium Hexavalent
chromium
Polybrominated
biphenyl
Polybrominated
diphenyl ether
Printed circuit board
Projection lens
Projection light source
Enclosure
Mechanical parts
Remote control
Other accessories
Remark
Remark
“only refers to the percentage of the restricted substance not exceeding the
percentage content reference value.
“only refers to that the restricted substance is excluded.
Restricted substances and their chemical symbols

12
Do not place anything around he vents. Otherwise, it may cause internal heat
accumulation. Do not place your hands or deformable items (plastic, etc.) near
the vents or around he projector. Otherwise, it may result in damage or
personal injury.
Caution
part name and function
1
2
Adjustable foot
3
Air inlet
4
Zoom ring
Focusing ring
55
6
Remote control window
12 Horn hole
14
15
Power socket
Rear remote control window
13
Safety lock
7Status indicator
8
9Adjustable foot
10 Air inlet
11
Safety bar
Control panel
Lens
Air outlet
1
23
4
5
6
t
t
11 14
13
12
8
7
9
10

13
Do not place anything around he vents. Otherwise, it may cause internal heat
accumulation. Do not place your hands or deformable items (plastic, etc.) near
the vents or around he projector. Otherwise, it may result in damage or
personal injury.
Caution
part name and function
1
2
Adjustable foot
3
Air inlet
4
Zoom ring
Focusing ring
55
6
Remote control window
12 Horn hole
14
15
Power socket
Rear remote control window
13
Safety lock
7Status indicator
8
9Adjustable foot
10 Air inlet
11
Safety bar
Control panel
Lens
Air outlet
1
4
15
14
13
8
12
2
3
5
6
7
9
10 11

14
part name and function
RS-232C compatible control interface.
Connect the RS-232C interface of the
computer to the RS-232C straight-through
cable.
Connect the power cord to this connector.
Connect a network cable.
8
AC IN（~）jack
When using the “USB Display” function,
connect a USB storage device to this
terminal.
Connect HDM-compatible video devices and
computers.
1
Terminal panel
3
4
10
11
12
Connect HDM-compatible video devices and
computers.
Receive remote control signals
Remote control signal receiver
13
5
6
7
When using the “USB Display” function,
connect a USB storage device to this
terminal.
Connect the computer's RGB output signal
to this terminal.
9
— This terminal is used to output from the
RGB analog signals input from VGA1 to
other displays.
Connect an external audio amplifier to this
terminal. This terminal outputs the sound
from the AUDIO IN terminal.
Connect the video output signal or
component video output to this terminal.
Connect the audio output connecting the
video device to this terminal.
2
3456 7
12
810 11 12
9
13
8
345
26 7 1
10 11
9
13 12

15
Rear control panel
①
Open or close the on-screen menu.
②▲▼
▲
▲
- Select an item or adjust the data in the on-screen menu.
- Adjust the volume.
③AUTO SETUP button
④MENU button
Perform various auto settings, including “Input Source Search”.
⑤OK button
- Enter the menu operation.
- Execute the selected item.
⑥INPUT button
Select the input source.
Turn the projector on or off.
part name and function
/VOL+,VOL-

16
WARNING
Indicator
WARNING
Indicator
POWER
Indicator
POWER
Indicator
Indicator
Standby The projector is plugged in and in standby mode.
Power-on state The projector is ready to project.
Sleep mode Enter sleep mode after no signal input for
a period of time.
（off )
（red on)
part name and function
（off ）（ green on)
（off ）(green flashing）

17
Remote
control
Turn the projector on or off.
Turn the timer on or off.
③Input source button
Enter the input source selection.
④Freeze button
Enter freeze mode.
⑤Black screen button
Enter the black screen mode.
Open or close the on-screen menu.
Enter the energy saver mode.
Energy saving button
⑩
Enter the default mode.
Display the input source information.
Enter the auto setup.
Keystone correction button
11
Default setup button
12
Display the projector information
menu.
Select the aspect ratio mode.
Image mode button
15
Sound mode selection.
Info button
16
Enter test image mode.
Aspect ratio button
17
Enter the mute mode.
Sound mode button
18
Reduce the volume.
Test pattern button
19
Increase the volume.
Mute button
20
Select image mode.
Perform keystone correction.
Display button
13
Auto setup button
14
Volume -
21
Volume +
22
Return to the previous menu.
Exit button
⑨
Menu button
⑧
⑦OK button
Enter the selected menu or execute the
selected adjustment item.
⑥button
Select an item or adjust the data in the
on-screen menu.
②Timer button
① button
part name and function
13
14
①② ③
④ ⑤
⑥
⑨
⑦
⑩
⑧
11
12
15
16
22
21
20
19
17
18

18
Remote control operating range
To ensure safe operation, observe the following :
When operating, point the remote control at
the projector’s sensing remote control
window (front and back).
The maximum operating range of the
remote control is 7 meters in front
of and behind the projector and
30 degrees in angle.
Remote control operation
● Use 2 AAA alkaline batteries.
● Replace two batteries at the same time.
● Do not use a new battery and an old battery at the same time.
● Avoid contact with water or other liquids.
● Do not place the remote control in a damp or hot environment.
● Do not drop the remote control.
● If battery fluid leaks in the remote control, carefully clean the battery box and then
load a new one.
● There is a danger of explosion if you use a battery other than the one specified in
this manual.
● Dispose of used batteries according to the instructions on the battery or local disposal
regulations or instructions.
● Insert the battery and make sure that the polarity of the battery matches the (+) and
(-) marks in the battery compartment.
30°
30°
7M
30°
30°
7M
Placing the projector
●Since the brightness of the room can significantly affect the effect of the projected
image, it is recommended to limit the indoor light in order to obtain the best picture.
● The approximate values shown in the figure below may differ from the actual size.
Throw distance table