PR Lighting XPar 1514 ZOOM User manual

1/20
XPar1514 ZOOM
PR-8210
The user manual contains important information about the safe installation and use of a projector. Please read
andfollowthese instructionscarefullyandkeepthemanual in asafeplaceforfuture reference.
PR LIGHTING LTD.
http://www.pr-lighting.com

2/20
INDEX
1.SAFETYANDWARNINGS
2. INSTUCTIONS
●CLEANINGANDMAINTENANCE
●TROUBLESHOOTING
3.APPEARANCE
4.INSTALLATION
●RIGGING
●PLACEAUNITONAFLATSURFACE
●INSTALLATIONOFBARNDOOR
●TRANSPORTATION
●POWERCONNECTIONS
●DMXCONTROLCONNECTION
●DMXTERMINATOR
5.SETUPANDCONFIGURATION
●FRONTPANELOPERATION
●DMXSTARTADDRESS
●STAND-ALONEMODE
●MASTER/SLAVEMODE
6.OPERATIONMENU
7.DMXPROTOCOL
8.TECHNICALDATA
9.CIRCUITDIAGRAMANDPCBCONNECTIONS
●CIRCUITDIAGRAM
●PCBCONNECTIONS
10.COMPONENTORDERCODES
3
4
4
4
5
5
5
5
6
6
6
7
7
8
8
8
8
8
10
12
15
17
17
18
19
ACCESSORIES
Thefollowing itemsare suppliedwith theprojectorandpleasecheck:
Name
Quantity
Unit
Remark
Gclamps
1
Pc
Power cord
1
Pc
XLRCable
2
Pcs
Safetycord
1
Pc
User manual
1
Pc
TransparentCover+seal+screws×6
1
Set
Optional
BarnDoor+ Frostpanel(Optional)
1
Set
Optional
Please note that as part of our ongoing commitment to continuous product development, specifications are subject to changewithout notice.
Whilst every care is taken in the preparation of the manual we reserve the right to change specifications in the course of product
improvement.Thepublisherscannotbeheldresponsiblefortheaccuracyoftheinformationherein,oranyconsequencearisingfromthem.
Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good
conditionbeforeinstallationanduse.Shouldtherebeany damagecausedbytransportation,consultyourdealeranddonotusetheunit.Any
damagecausedbyimproperusewillnotbeassumedbythemanufacturerand/ordealer.
Any future technical change in the user manual won’t be with any further notice.
Note: Forthe productsmade by GuangzhouPRlighting Ltd, thewarranty forthe whole product isoneyearstarting from the delivery date
butthelightsourceisnotwithinthewarranty.

3/20
1. SAFETYANDWARNINGS
.
NOTE
Before a projector’s installation, power-on,operationandmaintenance,pleasecarefullyread
thesafetyinformationhereinafter!
The followingsafetysignsareusedintheusermanual.
Warning
User
Manual
Electrical
shock
Goggles
Protective
Gloves
Flames
High
Temperature
● When unpacking , check if there is transportation damage before using the projector. Should there be
anydamagecausedbytransportation,consultyourdealeranddonotuseit.
●The manufacture is not responsible for loss caused by the user not following the manual or changing the
projectoras he/she likes
●Please be noted that the damage caused by changing the projector at willisnotwarranted.
●Donot hesitate to contactthedealerorthe manufacturer if anyquestionsoradvice.
●The unit with lower protection level is only used indoors, for those with IP65,theycan be used both indoorsand
outdoors.
● Use onlyindrylocations.Keep this unitawayfromrainand moisture,excessiveheat,humidityanddust.Donot
allowcontact withwateroranyotherliquids.
●It’s forbidden to make theunitwithlowerprotectionleveldirectlyorindirectlycontactwater or other liquids.
●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while
beingoperated
●The projector is only intended for installation, operation and maintenance by qualified personnel. And the
operationmuststrictlyfollowtheproceduresinthemanual
●No repairable parts in theprojectoranddo notopencoversfor maintenancebyyourself.
●Don’t look straightly intothelightsourcesespecially forepileptics,otherwiseeyeswillbeburned.
●Do not connect this device to any type of dimmerpack
●After lamp switched on, the minimumdistancebetween theprojector andilluminatedsurfaceis1.5m
●lens and other optical parts shall be replaced immediately if they have deformed or been damaged, otherwise the
lightoutput willbecompromised.
●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a
projectorwhilecovers(housing)are off
●Keep the lamp clean and do not touch it with bare hands.
●While operating it, wear protective items.
●Any electrical connection must be carried out by a qualified person .
●Before installation, please confirm the voltage supplied matches what is required for the projector
●Each projector must be properlyearthed and installedasperrelatedelectrical standards.
●Do not use power cord with its insulator damaged and connect the power cord with other cables.
●If the projector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it forcefully or
bypullingthepowercable.
●All powercords mustconformtorelatedsafetyandregulations
●While beingoperated,theprojector shouldnotbeunderrainsorinhumidity.
●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other
electricalparts’ lifewillbeshortened .
●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety cord

4/20
suppliedthroughthesafetycord holesforsafetysupport.
●Before any installation, maintenance and cleaning work, please ensure the projector is disconnected frompower
mains.
●Under normal temperature, the temperature of the housing will be 55℃; after being stable, the unit’s
surface temperaturewillbe70℃
●While the lamp isstricken for the first time, there will be smoke and strange smell.It’s normal and does not
meantheprojectorhassomedefects.
●While operated, do not touch the metallic housing. It is very hot during operation.
●Do not mount the projector directly on inflammable surface.
●Do not project the beam straightly on combustible items and the minimum distance between the projector
andilluminateditemsis10m.
●A projector should be installed with good ventilation and the minimum distance between the projector and
wallsis50cm.Atthesametime,pleaseensurethefansandairinletsandoutlets areworkable.
2. INSTRUCTIONS
●CLEANINGANDMAINTENANCE
For the units with optical lens, because of the accumulation of the smoke, oil and dust on lens, the light output will be
compromised. For the reliable use of the unit, it is very necessary to keep it clean. The unit is IP67 rating waterproof device.
Unless approval by some professional technician for necessary internal component replacement, it’s forbidden to dismantle the
unit.
Cleaning frequencyisto be decided byoperations and itsenvironment. Use soft cloth and normal detergent for glass for cleaning
work. It’s advised external optical system be cleaned every 20days. Keep lens clean and do not touch optical parts with bare
hands.
●Beforeanymaintenance and cleaning,pleaseensuretheprojectisoff thepower
●Onlyqualifiedpersonisallowedtodomaintenance
●During maintenanceandbeforemaintenance, the projectormustbeoff power.
●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens whether
itrunsornot
●Do not use alcohol or other organic solvent to clean the housing to avoid damage.
●Do not use any solvent with chemical elements to clean color filters or hot mirror.
●TROUBLESHOOTING
PROBLEM
ACTION
The projector doesn’t switchon
Checkthe powercord connection
Power Switch fails or is not connected well, call a professional
technicianforrepairingandchecking
Control board is not connected normally, call a professional technician
forrepairing andchecking,
Theprojectcanbe turnedon, butthe LED lamps
can’t be on
LED lamp board is notconnected well, call a professional technician for
repairing and checking
TheLEDlamps canbeon,butnotcontrolled
byDMX
CheckifDMXStartAddressisproperlyset
CheckifXLRcable failsornot
Thebrightnessdecreasesobviously
Ambient temperature is too hot which makes the projector too hot,
please takeappropriateventilationmeasures

5/20
3. APPEARANCE
4. INSTALLATION
●RIGGING
Take 1 clamp and 1 safety cord out from the package and tighten the clamp with the arm, and then mount the whole unit on the truss,
tighten the clamp’s retainers to keep the unit stable. (See the WARNING on the underside of the base as shown above) To pass the
SAFETYCORDthroughtheARM forsafety!Always ensurethatthe unitisfirmlyanchoredtoavoid vibrationand slippingwhilst
functioning. Always ensure thatthe structure that you are goingto mount the unitto is secureand strongenough to support the weight
ofthe unit Loosen thebigknob and adjust the head’s angle for the effect desired and the tighten it. The installation is completed.
(ifthe unitiswit wirelesscontrol,while beinghung,theantennashouldfacedown)
●PLACEAUNITONAFLATSURFACE
Before placing a unit on a flat surface, loosen the small knob with the support and make the angle between the arm and the support
60degrees.Tightenthesmallknob. Loosenhebigknobandadjusttheanglebetweenthe armand unitasdesiredandthentightenit.
.(Ifthe unitis with wireless control, after the unit isplaced ona flatsurface the antenna should face up)
Barn door
Body
Arm
Arm
Safety cord
Clamp
Warming:
For safety, please
run the safety cord
through the arm and
ensure it is tightened。

6/20
●INSTALLATION OFBARNDOOR
If barn doorselected, its installationisillustratedin thediagrambelow:
Loosen the screw in the shapeofa butterflyin thefrontpart of the unit, turn the clipping component in the shape of 7 by
a little amount, then place the barn door. Turn the clipping component backward and tighten the butterfly screws. Hook
the safetycord on the barn to the safety cord hole in the middle of the unit to finish the installationofthe barn door. Turn
thebarn door, and openorclosethe barn doorbladesto reach the effectdesired.
●TRANSPORTATION
Beforetransportation,tightenbothknobs after thearmand supportare overlapped.
WARNING:
●The projectorMUSTbeliftedorcarriedbythe HANDLESinsteadofclamps.
●.For safety the safety cord should afford 10 times the Projector’s weight.
●POWERCONNECTION
Connect thepowercordasfollows:
L(live)=brown
E(earth) =yellow/green
N(neutral)=blue
Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that each
projectorbe connectedwithpowerseparatelysothat theymaybeindividuallyswitchedonandoff.
Note: If projectors are connected in series, please connect POWERIN port of the 1st projector with the Power Mains, then
connectitsPOWEROUTwithPOWERINof the 2nd projector,and soontillall fixturesareconnected.Ifthevoltage supplied
is 200V-240V, the maximum projectors connected is 8pcs, if it is 100V-120V, the maximum is 4pcs. The diameter of the cores
ofthe wiresforthePowerin/outcablesmustbeequalorbiggerthan2.5mm2.
●Theearthwire(yellow/green) must beconnectedto theground. And electricalconnection must be in
accordancewiththe standardsconcerned.
●Ifanyquestionsabouttheelectricalinstallation, donotcontinue butconsulta qualifiedelectrician.

7/20
●DMXCONTROLCONNECTION:
Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with
each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the
projector)or5 pinXLRplugsand sockets.TheXLR'sareconnectedasshowninthefigureabove.
Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets
mustn’t be connected in any way other than mentioned in the above figure. The unit accepts digital control signals in protocol
DMX512 (1990).
Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second
fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX
terminatorasshowninthe figurebelow.
●DMXTERMINATOR
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents
electricalnoise fromdisturbingandcorruptingthe DMXcontrolsignals.
The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected across pins 2 and 3, which is then plugged
intotheoutputsocketonthe lastprojectorinthechain.The connectionsareillustratedbelow.
POWER
DMX CONTROLLER
DMX OUTDMX IN
POWER OUTPOWER IN
DMX OUTDMX IN
POWER OUTPOWER IN
DMX TEMINATOR

8/20
5. SETUPANDCONFIGURATION
●FRONTPANELOPERATION
To browse through or modify the projector’s functions, press key ENTER for more than 3 seconds to unlock the control panel and
enter the menus. To set or browse through the projector’s functions, press key UP or DOWN. Press the key ENTER to enter the
submenus andthecurrentparameterswillbedisplayedwhile flashing.Presskey UP or DOWN tochangevalues(plusor minus)
Presskey ENTER to save your changesand enterintothe upperlevel menuwhile flashingsstop;
Presskey FUNC, it will returntothe upper menu(parametersnot saved)orbrowsethrough1st levelmenus;
Presskey FUNC for1 secondor none keyispushed for1minute,the menu willbeescapedandcurrentoperationmodedisplayed.
●DMXSTARTADDRESS
EachProjectormustbe givena DMXstartaddressso thatthe correctprojectorrespondsto the correct controlsignals. ThisDMXstart
address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the
controller.TheUnithas5DMXmodes.Therearebasic,standard, extendedand HIS/HSICmodes.Forexample standard modehas9
channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 010, No. 3 projector’s address 019, No. 4 projector’s
address028,and soon.
Launchtheprojector. Pressbutton ENTER morethan2secondsto unlockpanel.
Pressbutton ENTER to displayDMXaddress;
Pressbutton UP and DOWN, youcansettheaddress;
Pressbutton ENTER to confirm;afterpoweredonnexttime,the defaultwillbelast value saved
Pressbutton FUNC, it willreturntotheuppermenu
IfDMX signalisavailable, LEDindicationison.Otherwiseitisoff.
.
●STAND-ALONEMODE
Operate the projector without connecting with a controller, enable the master mode through the operation panel, the
projector will run in Stand-Alone mode automatically.
DMX address can be set at any number within 512.
●MASTER/SLAVEMODE
Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,
connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR control cable and then connect the second
fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the
last fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.
StartAddressesofallSlavesare001; Operationmodeof the Master can be set any mode for a Master’ and Slaves’ operation mode can
21
3
120
DMX TERMINATOR
CONNECTION
Connect a 120 (OHM) resistor
across pins 2 and 3 in an XLR plug
and insert into the DMX out socket
on the last unit in the chain. PIN 3
PIN 2

9/20
besetaccordingly
After Poweredon,thegroup willrun in Master/SlaveMode
POWER
DMX CONTROLLER
DMX OUTDMX IN
POWER OUTPOWER IN
DMX OUTDMX IN
POWER OUTPOWER IN
DMX TEMINATOR
Slave Slave Master

10/20
6. OPERATION MENU
1stlevelmenu
2nd levelmenu
3rd levelmenu
4thlevel menu
DMXAddress
001 -501
DMX 地址
Reset
ZoomReset
Yes
ConfigSetup
DMX ChannelMode
Basic
Standard
Extended
HSI
HSIC
MasterSlave
Slave
Default：Slave
Master
ZOOM Position
000 - 255
Forpresetmemory
ColorOffset
Red
Green
Blue
LanguageSetup
English
Default：English
Chinese
LcdLightSetup
On
The LCDbacklightwill
beturned off3minutes
afternonekeyispushed.
Off
DisplayInvert
Yes
No
FactorySetting
Yes
PRMTransmit
Yes
cleanProgra
Yes
Information
LEDTemperature
XX
FixtureuseTime
XXXX
SoftwareVersion
X.X.X
TestMode
Red
Green
Blue
White
RGb
Rwb
RGbw
ZOOM
000 -255
Motorposition
OperationMode
DMX Mode
Yes
UserMemory
Yes

11/20
PresetMemory
（PR01~PR16）
UserPrograEdit
（ET01~ET16）
Dimmer
000 -255
Strob
000 -255
Red
000 -255
Green
000 -255
Blue
000 -255
White
000 -255
Zoom
000 -255
KeepTime
000 –200 (0-20S)
Note:
1. In one DMX chain, only one unit can be made as the master. Before master works, unplug its XLR cable connected with the
console.
2. The parameters transmitted from the master include after several units are synchronized: DMX channel mode, display
settings(display contrast excluded),operation mode(including user memory).During parameter transmission, set the unit
transmittingdataasmasterandothersasslave

12/20
7. DMXPROTOCOL
Basic
mode
Standard
mode
Extended
mode
HSI
HSIC
Function
DMXValue
Description
1
1
Hue
000-255
8bithue
2
2
HueFine
000-255
16bithue
3
3
Saturation
000-255
1
1
1
4
4
Brightness
000-255
Linear adjustment from
darktobright
2
2
BrightnessFine
0-255
Brightness adjustment in
16bit
2
3
3
5
5
Strobe
000-007
No
008-255
Strobe speed from slow to
fast
3
4
6
Colour
Temperature
000
No
001-255
CTfromhighto low
4
5
Macro
000-016
No
017-024
White（CT10000K）
025-032
White （CT7200K）
033-040
White （CT5600K）
041-048
White （CT3200K）
049-056
LightBlue
057-064
Yellow
065-072
Magenta
073-080
Red
081-088
Green
089-096
Blue
097-104
Cyan
105-112
Amber
113-120
Orange
121-128
Pink
129-255
Rainbow effect from slow
tofast
4
6
Red
000-255
Lineardimmerfromdarkto
bright
5
7
Green
000-255
Lineardimmerfromdarkto
bright
6
8
Blue
000-255
Lineardimmerfromdarkto
bright
7
9
White
000-255
Lineardimmerfromdarkto
bright
5
8
10
6
7
Zoom
000-255
Beam angle from big to
small
11
PresetMemory
000
No

13/20
001-015
Presetmemory1
016-031
Presetmemory2
032-047
Presetmemory3
048-063
Presetmemory4
064-079
Presetmemory5
080-095
Presetmemory6
096-111
Presetmemory7
112-127
Presetmemory8
128-143
Presetmemory9
144-159
Presetmemory10
160-175
Presetmemory11
176-191
Presetmemory12
192-207
Presetmemory13
208-223
Presetmemory14
224-239
Presetmemory15
240-255
Presetmemory16
12
UserMemory
000
No
001-015
UserMemory1
016-031
UserMemory2
032-047
UserMemory3
048-063
UserMemory4
064-079
UserMemory5
080-095
UserMemory6
096-111
UserMemory7
112-127
UserMemory8
128-143
UserMemory9
144-159
UserMemory10
160-175
UserMemory11
176-191
UserMemory12
192-207
UserMemory13
208-223
UserMemory14
224-239
UserMemory15
240-255
UserMemory16
`
13
PresetMemory
Speed
000-015
Speed1，fastest
016-031
Speed2
032-047
Speed3
048-063
Speed4
064-079
Speed5
080-095
Speed6
096-111
Speed7
112-127
Speed8
128-143
Speed9
144-159
Speed10
160-175
Speed11

14/20
Note:DMXchannelpriority: Preset memory> usermemory>Macros>CT>RGBWdimming
Whilehigherprioritychannelsarein use, lower priority channels don’t work.
176-191
Speed12
192-207
Speed13
208-223
Speed14
224-239
Speed15
240-255
Speed16，Slowest
6
9
14
7
8
Function
0-188
Reserved
180-189
ZoonReset
190-255
Reserved

15/20
8. TECHNICALDATA
INPUTVOLTAGES
100V~240VAC，50/60Hz
RATEDPOWER
220W@220V
LIGHTSOURCESPECIFICATIONS
Qty 14pcs, Osram,15WRGBWB,4in1, SMT LED
Power Consumption 15W ,14pcs
ManufacturersRated LampLife 50000hours
Colortemperature: 2700K~10000K，linearadjustment
COLORS
R/G/B/W, Macros, unlimited colormixings
DIMMER
Linear Dimmer from0-100%
STROBE
ElectronicStrobe0-25FP.S.withpresetstrobepulseeffect
BEAMANGLE
Fieldangle(1/10peak) θ: 12°～ 69°,linearadjustment
Beam Angle(1/2peak) θ1/2 6°～ 36°,linearadjustment
CONTROL
InternationalstandardDMX512 signalcontrolprotocol
DMX512 3pin and5pininterfaces
5controlmodes.Basic,standard,extendedandHIS/HSICmodes
Master/SlavesynchronizedMode
Standard alonemode,presetmode, selftest mode and singlescenemode
3operationmodes(DMX mode, user memory, presetmemory)
OTHERFUNCTIONS
LCDscreenanditsbrightnessadjustable
Wirelesscontrolfunction(Optional)
DMX512portforfirmware upgrade,a convenient and quickwayfor firmware upgradeviaDMXcable
Overtemperatureprotection
Fixturetime,DMX512channelvalueandsoftwareversionwillbedisplayed
Displaycanbeinverted
HOUSING:Hightensile castAluminum alloy, IP67
NETWEIGHT
10Kg

16/20
OPERATIONTEMPERATURE
Maximumambienttemperature: 40 ℃
SIZES:
LIGHTOUTPUT:
Note：The luminous flux is measured when the hotspot is 1m in diameter and the bean angle 69 degrees.
6.0°DIAMETER (m)
DISTANCE (m)
5m
6m
5m
6m 7m
4m
2m
4m
2m
0m 1m
1m
3m
3m
7m
0 2.5 5 7.5 10 12.5 15
0.52 1.05 1.57 2.09 2.62 3.14
6.0°Lux 23334 5834 2593 1458 933 6480
0
810 202 90 51 32 22 0
36.0°Lux

17/20
9. CIRCUITDIAGRAMANDPCBCONNECTIONS
●CIRCUITDIAGRAM

18/20
●PCBCONNECTIONS
MasterBoard
Diver board
序号
名称
1
Temperature
2
Empty
3
PWM dimming
4
MOTOR
5
Power
6
Fan
7
Empty
8
Empty
9
DMX signal
10
Empty
No
Name
1
LED Dimming
2
Power
3
Temperature

19/20
10. COMPONENTORDERCODES
No.
Name
CodeNo.
Qty
Remarks
1
STEPPING MOTOR
6030040235A
1
2
POWERSWITCH
6192010188
1
3
MASTERBOARDOFPR-8210
6230000001
1
4
LAMPBOARDOFPR-8210
6230000002
1
5
MIXINGROD OFPR-6200
6290000005
14

20/20
PR LIGHTING LTD.
1582 XingyeAvenue,Nancun Panyu
Guangzhou,511442 China
TEL:[phone]
PR lighting will try its best to offer accurate and overall information about a product’s technical data. Any changes won’t be notified if necessary. Patented Products.
CounterfeitingWillbeProsecuted!
P/N: 6320000001
Version: 20170830