BLK BOX 21-0577 User manual

OWNERS MANUAL & QUICK START GUIDE
CORNER POD
NOTE : PLEASE READ ALL THE INSTRUCTIONS
CAREFULLY BEFORE ASSEMBLING THIS PRODUCT.
BLK BOX
PRODUCT WEIGHT
MAX USER WEIGHT
DIMENSIONS
-167kg
150kg
2151mm x 786mm x 2408mm
-
-
21-0577
#MADEINBELFAST
PRODUCT SPECIFICATION

WARNING
xx
Nm
SPIRIT LEVEL
10MM MASONRY
TOOLS REQUIRED
17MM SPANNER X2
13MM SPANNER
HAMMER
HAMMER VACU-STEP LADDER
PARTS & ATTACHMENTS
No. Name SKU QTY
1 GOLIATH UPRIGHT 21-0036 4
2 0.7 BRANDING BOX 21-0578 1
3 CORNER POD ANGLED CM 21-0581 4
4 SLOTTED ANGLED CM 21-0582 2
5 CORNER POD FRONT CM 21-0583 1
6 BOLT ON ANGLED SIDE PLATE 20-0048 4
7 BOLT ON FLAT SIDE PLATE 20-0049 4
8 0.7 DB SHELF 21-0580 2
9 0.7 FLAT SHELF 21-0579 1
10 0.7 BALL SHELF 21-0586 1
11 DNA60 MULTIGRIPS 21-0151 1
12 MAT HANGER 21-0584 2
13 BAND HOLDER 20-0069 1
14 M10X30 BOLT 10-0001 16
15 M10 WASHER 10-0019 110
16 M10 NYLOCK NUT 10-0024 46
17 M10 WING NUT 10-0018 6
18 M10X80 BOLT 10-0006 6
19 M10X90 BOLT 10-0008 30
20 M10 SLEEVE ANCHOR 10-0031 6
21 M20X100 BOLT 10-0016 16
22 M20 NYLOCK NUT 10-0028 16
23 M20 WASHER 10-0023 32
1
2
3
4
11
6
SERIOUS OR FATAL INJURIES MAY OCCUR FROM INCORRECTLY ASSEMBLED EQUIPMENT. ALWAYS ENSURE
BOLTS ARE TIGHTENED CORRECTLY AND ALL PARTS ARE LEVEL AND PLUMB. TO FURTHER REDUCE RISK OF
INJURIES OR DEATH PLEASE USE OUR SUGGESTED TOOLS AND PERSONAL PROTECTIVE EQUIPMENT (PPE).
WE SUGGEST THAT A MINIMUM OF THREE PEOPLE ARE INVOLVED IN THE ASSEMBLY OF THIS PRODUCT.
EACH PERSON SHOULD BE EQUIPPED WITH SAFETY GLASSES, STEEL TOE CAP BOOTS AND EAR PLUGS.
PLEASE BE AWARE OF THIS SYMBOL AS AN INDICATION TO CHECK THAT A PART IS LEVEL
OR PLUMB.
THIS SYMBOL IS AN INDICATION OF THE RECOMMENDED TORQUE EACH
BOLT SHOULD BE TIGHTENED TO. THIS VALUE WILL BE DEPENDENT ON
THE BOLT TYPE. PLEASE HAND TIGHTEN ALL BOLTS UNTIL YOU SEE THIS SYMBOL.
#MADEINBELFAST
8
20
21
22
23
16 15
5
7
12 13
9
10
14
19
18
17

ASSEMBLY
1
BUILD UP EACH SHELF ASSEMBLY USING SIDE PLATES ( 20-0048 / 20-0049 ) AND M10X30 BOLTS
(10-0001). BUILD UP MIDDLE SECTION AS PICTURED BELOW PLACING 1QTY BRAND BOX (21-0578)
AND SHELF ASSEMBLIES BETWEEN 2QTY UPRGIHTS (21-0036) WITH BOLT ASSEMBLIES AS SHOWN.
ENSURE LOGO ON UPRIGHTS ARE FACING OUT.
10.0016
10.0023 x2
10.0028
10.0008
10.0019 x2
10.0024
#MADEINBELFAST

2
BOLT 1QTY MULTIGRIP ( 21-0151 ) TO 1QTY FRONT CM ( 21-0583 ) AND ATTACH BETWEEN 2QTY UPRIGHTS
(21-0036). CONNECT TO EXISTING ASSEMBLY USING BOLT ASSEMBLY AS SHOWN. ENSURE LOGO ON
UPRIGHTS ARE FACING OUT AND BOLTS ARE FACING INWARD.
#MADEINBELFAST
10.0016
10.0023 x2
10.0028
10.0008
10.0023 x2
10.0028

3
ENSURE ALL UPRIGHTS ARE PLUMB AND BOLT TO GROUND USING SLEEVE ANCHOR GUIDE
AS SHOWN BELOW. TIGHTEN ALL BOLTS TO 30NM AND ATTACH MAT HANGER (21-0584)
AND BAND HOLDER (20-0069) TO SLOTTED CM (21-0582) USING M10X80 BOLTS (10-0006)
AND WING NUTS (10-0018).
#MADEINBELFAST
30
Nm
-DRILL 10MM HOLE
THROUGH FLOOR
COVERING, 90MM
DEEP USING PLATE
AS A GUIDE.
-VACUUM OUT THE
DUST.
-HAMMERSLEEVE
ANCHOR DOWN
INTO THE HOLE.
-TIGHTEN SLEEVE
ANCHOR TO
SPECIFIED TORQUE
USING 13MM
SPANNER.
DRILL
HOLE
VACUUM
HAMMER
IN BOLT
TIGHTEN
90MM