BLK BOX 21-0875 User manual

OWNERS MANUAL & QUICK START GUIDE
BINARY RACK
NOTE : PLEASE READ ALL THE INSTRUCTIONS
CAREFULLY BEFORE ASSEMBLING THIS PRODUCT.
BLK BOX
21-0875
#MADEINBELFAST
628mm x 1450mm x 2212mm
2128mm x 2950mm x 3076mm
55kg
PRODUCT SPECIFICATION
PRODUCT WEIGHT
MAX USER WEIGHT
MAX USER
MAX TRAINING
WEIGHT
DIMENSIONS
-125kg
200kg
-
-
-
-
1
-

SERIOUS OR FATAL INJURIES MAY OCCUR FROM INCORRECTLY ASSEMBLED EQUIPMENT.
ALWAYS ENSURE BOLTS ARE TIGHTENED CORRECTLY AND ALL PARTS ARE LEVEL AND PLUMB.
TO FURTHER REDUCE RISK OF INJURIES OR DEATH PLEASE USE OUR SUGGESTED TOOLS AND
PERSONAL PROTECTIVE EQUIPMENT (PPE). WE SUGGEST THAT A MINIMUM OF THREE PEOPLE
ARE INVOLVED IN THE ASSEMBLY OF THIS PRODUCT. EACH PERSON SHOULD BE EQUIPPED WITH
SAFETY GLASSES, STEEL TOE CAP BOOTS AND EAR PLUGS.
PLEASE BE AWARE OF THIS SYMBOL AS AN INDICATION TO CHECK THAT A PART
IS LEVEL OR PLUMB.
WARNING
SPIRIT LEVEL
10MM MASONRY
DRILL BIT
TOOLS REQUIRED
2x 30MM SPANNER
2x 17MM SPANNER
1x 13MM SPANNER
HAMMER
HAMMER DRILL VACUUM STEP LADDER
PARTS & ATTACHMENTS
#MADEINBELFAST
1
2
3
4
8
67
910
11 12 13
14
TAPE MEASURE
5
No. Name SKU QTY
1 U-CHANNEL BRACKET 20-0703 2
2 GOLIATH FOLDING RACK
BOX
21-0551 4
3 GOLIATH FOLDING RACK
UPRIGHT
21-0557 2
4 GOLIATH FOLDING RACK
PU BAR
21-0553 1
5 M20X100 BOLT 10-0134 8
6 M20 NYLOCK NUT 10-0028 8
7 M20 WASHER 10-0023 16
8 M10 SLEEVE ANCHOR 10-0031 8
9 M10 WASHER 10-0019 16
10 HITCH PIN 16-0004 2
11 LOCATING PIN 10-0160 2
12 M10X100 BOLT 10-0067 4
13 M10 NYLOCK NUT 10-0271 4
14 J-HOOK PAIR 16-0001 1

ASSEMBLY
1MARK THE 8 LOCATIONS FOR THE WALL MOUNTED U- BRACKETS AS SHOWN
BELOW.
TIP: USE U-BRACKET AS TEMPLATE.
#MADEINBELFAST
GROUND
204mm
1929mm
MAX 400mm MAX 400mm
1150mm

#MADEINBELFAST
2CHECK THAT THE BRACKETS (20-0703) ARE LEVEL AND ALIGN WITH THE
HOLES THAT HAVE BEEN MARKED OUT. DRILL AND SECURE BRACKETS USING
SLEEVE ANCHOR GUIDE BELOW.
30
Nm
DRILL HOLE VACUUM HAMMER IN
BOLT TIGHTEN
90MM
SLEEVE ANCHOR BOLT FITTING
-DRILL 10MM HOLE IN WALL, 90MM DEEP
USING BRACKET AS A GUIDE.
-VACUUM OUT THE DUST.
-HAMMER SLEEVE ANCHOR INTO THE
HOLE.
-TIGHTEN SLEEVE ANCHOR TO SPECIFIED

#MADEINBELFAST
3BOLT 4 QTY BOX CM (21-0551) TO 2 QTY U-BRACKET (20-0703) USING BOLT ASSEMBLY
AS SHOWN. ENSURE YOU DON’T OVER TIGHTEN.
10.0067
10.0019 x 2
10.0271
1

5
BOLT 2 QTY UPRIGHT (21-0557) TO 4 QTY BOX CM (21-0551). ENSURE THE LOGOS
ON UPRIGHTS ARE FACING OUTWARDS AND ALL BOLTS FACING INWARDS.
#MADEINBELFAST
10.0134
10.0023 x 2
10.0028

#MADEINBELFAST
6
ATTACH 1 QTY PULL UP BAR (21-0553) WITH 2 QTY UPRIGHTS USING 2 QTY
HITCH PINS (16-0004)